DOWNLOAD Harman Kardon HS 300 (serv.man2) Service Manual ↓ Size: 3.78 MB | Pages: 73 in PDF or view online for FREE

 

 

page 5 of  69 

Ref. No. : JSH006020709-002 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

6 HAZARDOUS 

RADIATION 

Pass 

6.1 

Ionizing radiation < 36 pA/kg (0,5 mR/h) 

No ionizing radiation 

N/A 

6.1 

EN 60065 

European Council Directive 96/29/Euratom of 13 
May 1996 10cm from outer surface of apparatus 
<1µSv/h (0,1mR/h) 

No ionizing radiation 

N/A 

6.2 

Laser radiation, emission limits to IEC 60825-1  .... : Class 1 

Pass 

 

Emission limits under fault conditions .................... : Laser Optical Pickup:Class 1 

Pass 

 

7 

HEATING UNDER NORMAL OPERATING CONDITIONS 

Pass 

7.1 

Temperature rises not exceeding specified values, 
no operation of fuse links 

(see appended table) 

Pass 

7.1.1 

Temperature rise of accessible parts 

(see appended table) 

Pass 

7.1.2 

Temperature rise of parts providing electrical 
insulation 

(see appended table) 

Pass 

7.1.3 

Temperature rise of parts acting as a support or as 
a mechanical barrier 

(see appended table) 

Pass 

7.1.4 

Temperature rise of windings 

(see appended table) 

Pass 

7.1.5 

Parts not subject to a limit under 7.1.1 to 7.1.4 

(see appended table) 

Pass 

7.2 

Softening temperature of insulating material 
supporting parts conductively connected to the 
mains carrying a current > 0,2 A at least 150

 o

C 

No such supporting parts 

N/A 

 
 

8 

CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION 
AGAINST ELECTRIC SHOCK 

Pass 

8.1 

Conductive parts covered by lacquer, paper, 
untreated textile oxide films and beads etc. 
considered to be bare 

PCB, windings 

Pass 

8.2 

No shock hazard when changing voltage setting 
device, fuse-links or handling drawers etc. 

Tools are required 

Pass 

8.3 

Insulation of hazardous live parts not provided by 
hygroscopic material 

No hygroscopic material used 

Pass 

8.4 

No risk of electric shock following the removal of a 
cover which can be removed by hand 

Tools are required 

Pass 

8.5 

Class I equipment 

 

N/A 

 

Basic insulation between hazardous live parts and 
earthed accessible parts 

 N/A 

 

Resistors bridging basic insulation complying with 
14.2.1 a) 

 N/A 

 

 

page 6 of  69 

Ref. No. : JSH006020709-002 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

8.6 

Class II equipment and Class II constructions 
within Class I equipment 

 Pass 

 

Reinforced or double insulation between 
hazardous live parts and accessible parts 

 Pass 

 

Components bridging reinforced or double 
insulation complying with 14.1 a) or 14.3 

T501, T502 

Pass 

 

Basic and supplementary insulation each being 
bridged by a capacitor complying with 14.2.1 a) 

 N/A 

 

Reinforced or double insulation being bridged with 
2 capacitors in series complying with 14.2.1 a) 

 N/A 

 

Reinforced or double insulation being bridged with 
a single capacitor complying with 14.2.1 b) 

CY1, CY2, CY501, CY502 

Pass 

 

Basic insulation bridged by components complying 
with 14.3.4.3 

 N/A 

8.7 

Basic insulation between parts at 35 V to 71 V 
(peak) a.c. or 60 V to 120 V d.c. and accessible 
parts 

No such voltage 

N/A 

 

Reinforced or double insulation between circuits 
operating at voltages between 35 V and 71 V 
(peak) a.c. or between 60 V and 120 V d.c. and 
hazardous live parts at higher voltage 

 N/A 

 

Separation by Class II isolating transformer 

 

N/A 

 

Separation by Class I transformer 

 

N/A 

 

Separation by earthed conductive part 

 

N/A 

8.8 

Basic or supplementary insulation > 0,4 mm (mm) :  

N/A 

 

Reinforced insulation > 0,4 mm (mm) .................... : T501 bobbin:> 0.8mm 

T502 bobbin: >0.8mm 

Optocoupler U502, U504, 
U505: 0.40mm 

Enclosure (front panel): 
>1.5mm 

Separation sheet on internal 
enclosure under power board: 
0.51mm. 

Pass 

 

Thin sheet insulation 

Inside T501, T502 

Pass 

 

Basic or supplementary insulation, at least two 
layers, each meeting 10.3 

Withstand 2120Vp test. 

Pass 

 

Basic or supplementary insulation, three layers any 
two of which meet 10.3 

 N/A 

 

Reinforced insulation, two layers each of which 
meet 10.3 

 N/A 

 

 

page 7 of  69 

Ref. No. : JSH006020709-002 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

 

Reinforced insulation, three layers any two which 
meet 10.3 

Withstand 4240Vp test. 

Pass 

8.9 

Adequate insulation between internal hazardous 
live conductors and accessible parts 

           

N/A 

 

Adequate insulation between internal hazardous 
live parts and conductors connected to accessible 
parts 

           

N/A 

8.10 

Double insulation between conductors connected 
to the mains and accessible parts 

Live wires are double 
insulated, no secondary wire 
can come closer to live parts 

Pass 

8.11 

Detaching of wires 

      

N/A 

 

No undue reduction of creepages or clearance 
distances if wires become detached 

Mating lock connector used for 
mains. No risk of detached. 

N/A 

 Vibration 

test carried out  ........................................ : No, see above 

N/A 

8.12 

Adequate cross-sectional area of internal wiring to 
mains socket-outlets 

 N/A 

8.13 

Adequate fastening of windows, lenses, lamp 
covers etc. (pull test 20 N for 10 s) 

 Pass 

8.14 

Adequate fastening of covers (pull test 50 N for 
10 s) 

 Pass 

8.15 

No risk of damage to the insulation of internal 
wiring due to hot parts or sharp edges 

Internal wires secured and 
keep enough distance from 
sharp or hot parts. 

Pass 

8.16 

Only special supply equipment can be used 

 N/A 

8.17 

Insulated winding wire without additional 
interleaved insulation 

 N/A 

8.18 

Endurance test as required by 8.17 

 

N/A 

8.19 

Disconnection from the mains 

 

Pass 

8.19.1 

Disconnect device 

Mains plug or appliance 
coupler. 

Pass 

 

All-pole switch or circuit breaker with >3mm 
contact separation 

Not used as a disconnect 
device 

N/A 

8.19.2 

Mains switch ON indication 

Not used as a disconnect 
device 

N/A 

8.20 

Switch not fitted in the mains cord 

 

Pass 

8.21 

Bridging components comply with clause 14 

 

N/A 

 

 

page 8 of  69 

Ref. No. : JSH006020709-002 

 

IEC 60065 

Clause 

Requirement - Test 

Result - Remark 

Verdict 

 

9 

ELECTRIC SHOCK HAZARD UNDER NORMAL OPERATING CONDITIONS 

Pass 

9.1 

Testing on the outside 

Pass 

9.1.1 

For voltages >1000 V ac or >1500 V dc complies 
with clause 13.3.1 for basic insulation  

No such high voltage 

N/A 

9.1.1.1 

Touch current measured from terminal devices 
using the network in annex D ................................. :

U1<8.0Vp  
U2<0.10Vp 

Pass 

 

Discharge not exceeding 45 Μc <1μC Pass 

 

Energy of discharge not exceeding 350 Mj 

No voltage exceeding 15Kv 

N/A 

9.1.1.2 

Test with test finger and test probe 

 Pass 

9.1.2 

No hazardous live shafts of knobs, handles or 
levers 

 Pass 

9.1.3 

Ventilation holes and other holes tested by means 
of 4 mm x 100 mm test pin 

< 2 mm, no entering 

N/A 

9.1.4 

Terminal devices tested with 1 mm x 20 mm test 
pin (10 N); test probe D of IEC 61032 

 Pass 

 

Terminal devices tested with 1 mm x 100 mm 
straight wire (1 N); test probe D of IEC 61032 

 Pass 

9.1.5 

Pre-set controls tested with 2.5 mm x 100 mm test 
pin (10 N); test probe C of IEC 61032 

No pre-set control 

N/A 

9.1.6 

No shock hazard due to stored charge on 
withdrawal of the mains plug; voltage (V) after 2 s  :

< 5V 

Pass 

 

If C is not greater than 0,1 Μf no test needed 

> 0.2 μF 

N/A 

9.1.7 

Enclosure sufficiently resistant to external force 

 Pass 

 

Test probe 11 of IEC 61032 for 10 s (50 N) 

 Pass 

 

Test hook of fig. 4 for 10 s (20 N) 

 

Pass 

 

30 mm diameter test tool for 5 s (100 or 250 N) .... : 100N Pass 

9.2 

No hazard after removing a cover by hand 

Can not be removed by hand 

N/A 

 
 

10 INSULATION 

REQUIREMENTS 

Pass 

10.1 

Insulation resistance (MΩ) at least 2 MΩ min. after 
surge test for basic and 4 MΩ min. for reinforced 
insulation ................................................................. :

No antenna terminal. 

N/A 

10.2 Humidity 

treatment 48 h or 120 h ........................... : 120h, 40℃, 93%R.H. 

Pass 

10.3 

Insulation resistance and dielectric strength 

(See appended table) 

Pass