DOWNLOAD Harman Kardon HS 2X0 (serv.man2) Service Manual ↓ Size: 6.3 MB | Pages: 70 in PDF or view online for FREE

 

          Page 8 of 69 

      Report No.: SH10011244-002 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  TTRF_IECEN 60065I 

       TRF originator Intertek ETL SEMKO shanghai 

 

 

 

 

 

9 

ELECTRIC SHOCK HAZARD UNDER NORMAL OPERATING CONDITIONS 

 

9.1 

Testing on the outside 

 

9.1.1 

For voltages >1000 V ac or >1500 V dc complies 
with clause 13.3.1 for basic insulation  

No voltages exceeding 
1000Vac or 1500Vdc 

N/A 

9.1.1.1 

Touch current measured from terminal devices 
using the network in annex D ................................. :

U1=10.3Vp  
U2=0.30Vp 

Pass 

 

Discharge not exceeding 45 μC 

Less than 45

μC 

Pass 

 

Energy of discharge not exceeding 350 mJ 

No voltage exceeding 15kV 

N/A 

9.1.1.2 

Test with test finger and test probe 

 Pass 

9.1.2 

No hazardous live shafts of knobs, handles or 
levers 

 Pass 

9.1.3 

Ventilation holes and other holes tested by means 
of 4 mm x 100 mm test pin 

No enter. 

Pass 

9.1.4 

Terminal devices tested with 1 mm x 20 mm test 
pin (10 N); test probe D of IEC 61032 

Test probe did not become 
hazardous live parts after test. 

Pass 

 

Terminal devices tested with 1 mm x 100 mm 
straight wire (1 N); test probe D of IEC 61032 

Test probe did not become 
hazardous live parts after test. 

Pass 

9.1.5 

Pre-set controls tested with 2.5 mm x 100 mm test 
pin (10 N); test probe C of IEC 61032 

No such pre-set control used. 

N/A 

9.1.6 

No shock hazard due to stored charge on 
withdrawal of the mains plug; voltage (V) after 2 s  :

Less than the limit. 
Discharging resistor 
R501=R502=560 kΩ max 

Pass 

 

If C is not greater than 0,1 μF no test needed 

 N/A 

9.1.7 

Enclosure sufficiently resistant to external force 

 

Pass 

 

Test probe 11 of IEC 61032 for 10 s (50 N) 

No damage of enclosure and 
no hazardous live parts are 
accessible. 

Pass 

 

Test hook of fig. 4 for 10 s (20 N) 

No hazardous live parts are 
accessible. 

Pass 

 

30 mm diameter test tool for 5 s (100 or 250 N) .... : 100N 

Pass 

9.2 

No hazard after removing a cover by hand 

Tools required. 

N/A 

 

 

 

10 INSULATION 

REQUIREMENTS 

 

10.1 

Insulation resistance (MΩ) at least 2 MΩ min. after 
surge test for basic and 4 MΩ min. for reinforced 
insulation ................................................................. :

 Pass 

10.2 Humidity 

treatment 48 h or 120 h ........................... : 48h, 30℃, 95%R.H. 

Pass 

 

          Page 9 of 69 

      Report No.: SH10011244-002 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  TTRF_IECEN 60065I 

       TRF originator Intertek ETL SEMKO shanghai 

 

10.3 

Insulation resistance and dielectric strength 

(see appended table) 

Pass 

 

Insulation Resistance and dielectric strength 
across BASIC or SUPPLEMENTARY insulation 
(Class 1) 

Class II 

N/A 

 

Insulation resistance and dielectric strength across 
REINFORCED insulation (Class II) 

(see appended table) 

Pass 

 

 

 

11 FAULT 

CONDITIONS 

 

11.1 

No shock hazard under fault condition 

Single fault did not cause 
excessive voltage in output 
circuits. 

Pass 

11.2 

Heating under fault condition 

 

Pass 

 

No hazard from softening solder 

No softening of solder point 
and becoming fluid 

Pass 

11.2.1 

Measurement of temperature rises 

(see appended table) 

Pass 

11.2.2 

Temperature rise of accessible parts 

(see appended table) 

Pass 

11.2.3 

Temperature rise of parts, other than windings, 
providing electrical insulation 

(see appended table) 

Pass 

 

Temperature rise of printed circuit boards (PCB) 
exceeding the limits of table 3 by max. 100 K for 
max. 5 min 

(see appended table) 

Pass 

 

a) Temperature rise of printed circuit boards (PCB) 
to 20.1.3, exceeding the limits of table 3 by not 
more than 100 K for an area not greater than 2 cm²

         

 N/A 

 

b) Temperature rise of printed circuit boards (PCB) 
to 20.1.3 up to 300 K for an area not greater than 
2 cm² for a maximum of 5 min 

         

 N/A 

 

Meets all the special conditions if conductors on 
printed circuit boards are interrupted 

         

 N/A 

 

Class I protective earthing maintained 

Class II 

N/A 

11.2.4 

Temperature rise of parts acting as a support or 
mechanical barrier 

(see appended table) 

Pass 

11.2.5 

Temperature rise of windings 

(see appended table) 

Pass 

11.2.6 

Temperature rise of parts not subject to the limits 
of 11.2.1 to 11.2.5 

(see appended table) 

Pass 

 

 

 

12 MECHANICAL 

STRENGTH 

 

12.1.1 

Bump test where mass >7 kg 

Mass weight : 3.53 kg. 

Pass 

12.1.2 Vibration 

test 

 

N/A 

 

          Page 10 of 69 

      Report No.: SH10011244-002 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  TTRF_IECEN 60065I 

       TRF originator Intertek ETL SEMKO shanghai 

 

12.1.3 

Impact hammer test 

0.5J, no hazards after the test 

Pass 

 

Steel ball test 

2J, no hazards after the test 

Pass 

12.1.4 

Drop test for portable apparatus where mass < 7 
kg 

 N/A 

12.1.5 

Thermoplastic enclosures strain relief test 

70°C / 7 hours 

Pass 

12.2 

Fixing of knobs, push buttons, keys and levers 

 

Pass 

12.3 

Remote controls with hazardous live parts 

No remote control device with 
hazardous live parts 

N/A 

12.4 

Drawers (pull test 50 N, 10 s) 

No drawer is provided 

N/A 

12.5 

Antenna coaxial sockets providing isolation 

No antenna coaxial socket is 
provided as isolation 

N/A 

12.6 

Telescoping or rod antennas construction 

No such device 

N/A 

12.6.1 

Telescoping or rod antennas securement 

 

N/A 

 

13 

CLEARANCE AND CREEPAGE DISTANCES 

 

13.1 

Clearances in accordance with 13.3 

 Pass 

 

Creepage distances in accordance with 13.4 

 

Pass 

13.2 

Determination of operating voltage 

T502: 254Vrms, 536Vp 
T503: 275Vrms, 560Vp 

Pass 

13.3 Clearances 

 

Pass 

13.3.2 

Circuits conductively connected to the mains 
comply with table 8 and, where applicable, table 9

(see appended table) 

Pass 

13.3.3 

Circuits not conductively connected to the mains 
comply with table 10 

Such circuits are secondary 
circuit and do not include 
hazardous voltage, no basic, 
supplementary or reinforced 
insulation required. 

N/A 

13.4 Creepage 

distances 

 

Pass 

 

Creepage distances greater than table 11 minima  (see appended table) 

Pass  

13.5 Printed 

boards 

 

N/A 

13.5.1 

Clearances and creepage distances between 
conductors on printed circuit boards, one of which 
may be conductively connected to the mains, as in 
fig. 10 

 

N/A 

13.5.2 

Type B coated printed circuit boards complying 
with IEC 60664-3 (basic insulation only) 

 N/A 

13.6 

Conductive parts along uncemented joints 
clearances and creepage distances comply with 
13.3 and 13.4 

 N/A 

 

          Page 11 of 69 

      Report No.: SH10011244-002 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  TTRF_IECEN 60065I 

       TRF originator Intertek ETL SEMKO shanghai 

 

 

Conductive parts along reliably cemented joints 
comply with 8.8 

 N/A 

13.7 

Enclosed, enveloped or hermetically sealed parts: 
not conductively connected to the mains: 
clearances and creepage distances as in table 12

 N/A 

13.8 

Parts filled with insulating compound, meeting the 
requirements of 8.8 

Optocoupler are approved 
components.                      

Pass 

 

 

 

14 COMPONENTS 

 

14.1 Resistors 

 

 

a) Resistors between hazardous live parts and 
accessible metal parts 

R558 Pass 

 

b) Resistors, other than between hazardous live 
parts and accessible parts 

 N/A 

 

b) Resistors separately approved  .......................... : R558 approved by VDE

 

Pass 

14.2 

Capacitors and RC units 

 

Pass 

 

Capacitors separately approved 

Yes  

Pass 

14.2.1 

Y capacitors tested to IEC 60384-14, 2

nd

 edition  .. : Y1: CY501, CY502, CY503, 

CY504 

Pass 

14.2.2 

X capacitors tested to IEC 60384-14, 2

nd

 edition  .. : X2: CX501, CX502, CX503 

Pass 

14.2.3 

Capacitors operating at mains frequency but not 
connected to the mains: tests for X2  ..................... :

No such component 

N/A 

14.2.5 

Capacitors with volume exceeding 1750 mm³, 
where short-circuit current exceeds 0,2 A: 
compliance with IEC60384-1, 4.38 category B or 
better ....................................................................... :

Such capacitors with metal 
cased 

N/A 

 

Capacitors with volume exceeding 1750 mm³, 
mounted closer to a potential ignition source than 
table 5 permits: compliance with IEC 60 384-1, 
4.38 category B or better ........................................ :

Such capacitors with metal 
cased 

N/A 

 

Shielded by a barrier to V-0 or metal  ..................... :  N/A 

14.3 

Inductors and windings 

 

Pass 

 

Comply with IEC 61558-1, IEC 61558-2 
(as relevant) and clause 20.1.4 

 N/A 

14.3.1 

Transformers and inductors marked with 
manufacturer’s name and type .............................. :

Power transformer T502, T503 

Line filter LF501, LF502  

(See appended table14) 

Pass 

 

Transformers and inductors separately approved . : No 

N/A 

14.3.2 General 

 

Pass