Harman Kardon HKTS 7 (serv.man3) EMC - CB Certificate ▷ View online
Page 11 of 46
Report Ref No.: 615278
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
10 INSULATION
REQUIREMENTS
10.1
Insulation resistance (MΩ) at least 2 MΩ min.
after surge test for basic and 4 MΩ min. for
reinforced insulation .......................................... :
after surge test for basic and 4 MΩ min. for
reinforced insulation .......................................... :
No antenna terminal
N/A
10.2
Humidity treatment 48 h or 120 h ..................... : 48 h
P
10.3
Insulation resistance and dielectric strength
P
11 FAULT
CONDITIONS
11.1
No shock hazard under fault condition
P
11.2
Heating under fault condition
P
No hazard from softening solder
P
No flaming more than 10s
P
Soldered terminations not used as protective
mechanism
mechanism
N/A
11.2.1
Measurement of temperature rises
P
11.2.2
Temperature rise of accessible parts
P
11.2.3
Temperature rise of parts, other than windings,
providing electrical insulation
providing electrical insulation
P
Temperature rise of printed circuit boards
(PCB) exceeding the limits of table 3 by max.
100 K for max. 5 min
(PCB) exceeding the limits of table 3 by max.
100 K for max. 5 min
N/A
a) Temperature rise of printed circuit boards
(PCB) to 20.1.3, exceeding the limits of table 3
by not more than 100 K for an area not greater
than 2 cm²
(PCB) to 20.1.3, exceeding the limits of table 3
by not more than 100 K for an area not greater
than 2 cm²
N/A
b) Temperature rise of printed circuit boards
(PCB) to 20.1.3 up to 300 K for an area not
greater than 2 cm² for a maximum of 5 min
(PCB) to 20.1.3 up to 300 K for an area not
greater than 2 cm² for a maximum of 5 min
N/A
Meets all the special conditions if conductors on
printed circuit boards are interrupted
printed circuit boards are interrupted
At Uin=198V, voltage across
interruption <50Vp (see table 11)
interruption <50Vp (see table 11)
P
Class I protective earthing maintained
N/A
11.2.4
Temperature rise of parts acting as a support or
mechanical barrier
mechanical barrier
P
11.2.5
Temperature rise of windings
P
11.2.6
Temperature rise of parts not subject to the limits
of 11.2.1 to 11.2.5 Table 3 e) "Other Parts"
of 11.2.1 to 11.2.5 Table 3 e) "Other Parts"
P
Page 12 of 46
Report Ref No.: 615278
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
12 MECHANICAL
STRENGTH
12.1.1
Bump test where mass >7 kg
P
12.1.2
Vibration test (portable, metal, musical amps)
No connection or part which might
impair safety can become loose.
impair safety can become loose.
P
12.1.3
Impact hammer test
P
Steel ball test (for non-ventilated solid areas)
3.5J top, sides, back , front
P
12.1.4
Drop test for portable apparatus where mass ≤
7 kg
7 kg
N/A
12.1.5
Thermoplastic enclosures stress relief test
N/A
12.2
Fixing of knobs, push buttons, keys and levers
P
12.3
Remote controls with hazardous live parts
N/A
12.4
Drawers (pull test 50 N, 10 s)
N/A
12.5
Antenna coaxial sockets providing isolation
N/A
12.6
Telescoping or rod antennas construction
N/A
12.6.1
Telescoping or rod antennas securement
N/A
Page 13 of 46
Report Ref No.: 615278
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
13
CLEARANCE AND CREEPAGE DISTANCES
13.1
Clearances in accordance with 13.3
Prim – sec. >10mm
Prim – acc. metal parts : >10mm
Prim – acc. metal parts : >10mm
P
Creepage distances in accordance with 13.4
P
13.2
Determination of operating voltage
See TABLE 13
P
13.3
Clearances
13.3.2
Circuits conductively connected to the mains
comply with table 8 and, where applicable,
table 9
comply with table 8 and, where applicable,
table 9
P
13.3.3
Circuits not conductively connected to the
mains comply with table 10
mains comply with table 10
Circuits not conductively connected to
the mains cannot cause any shock
hazard.
the mains cannot cause any shock
hazard.
N/A
13.3.4
Measurement of transient voltages
P
13.4
Creepage distances
Creepage distances greater than table 11
minima
minima
P
13.5
Printed boards
13.5.1
Clearances and creepage distances between
conductors on printed circuit boards, one of
which may be conductively connected to the
mains, as in fig. 10
conductors on printed circuit boards, one of
which may be conductively connected to the
mains, as in fig. 10
N/A
13.5.2
Type B coated printed circuit boards complying
with IEC 60664-3 (basic insulation only)
with IEC 60664-3 (basic insulation only)
N/A
13.6
Conductive parts along uncemented joints
clearances and creepage distances comply
with 13.3 and 13.4
clearances and creepage distances comply
with 13.3 and 13.4
N/A
Conductive parts along reliably cemented joints
comply with 8.8
comply with 8.8
N/A
13.7
Enclosed, enveloped or hermetically sealed
parts: not conductively connected to the mains:
clearances and creepage distances as in
table 12
parts: not conductively connected to the mains:
clearances and creepage distances as in
table 12
N/A
13.8 Parts
filled with insulating compound, meeting
the requirements of 8.8
N/A
Page 14 of 46
Report Ref No.: 615278
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
14 COMPONENTS
14.1
Resistors
a) Resistors between hazardous live parts and
accessible metal parts
accessible metal parts
N/A
b) Resistors, other than between hazardous live
parts and accessible parts
parts and accessible parts
N/A
Resistors separately approved ......................... :
N/A
14.2
Capacitors and RC units
Capacitors separately approved
N/A
14.2.1
Y capacitors tested to IEC 60384-14, 2
nd
edition ................................................................ :
N/A
14.2.2
X capacitors tested to IEC 60384-14, 2
nd
edition ................................................................ :
N/A
14.2.3
Capacitors operating at mains frequency but
not connected to the mains: tests for X2 .......... :
not connected to the mains: tests for X2 .......... :
N/A
14.2.5
a)
a)
Capacitors with volume exceeding 1750 mm³,
where short-circuit current exceeds 0,2 A:
compliance with IEC60384-1, 4.38 category B
or better ................................................................
where short-circuit current exceeds 0,2 A:
compliance with IEC60384-1, 4.38 category B
or better ................................................................
N/A
b)
Capacitors with volume exceeding 1750 mm³,
mounted closer to a potential ignition source
than table 5 permits: compliance with
IEC 60 384-1, 4.38 category B or better ........... :
mounted closer to a potential ignition source
than table 5 permits: compliance with
IEC 60 384-1, 4.38 category B or better ........... :
N/A
Shielded by a barrier per Table 21 .................... :
N/A
14.3
Inductors and windings
Comply with IEC 61558-1, IEC 61558-2
(as relevant) and clause 20.1.4
(as relevant) and clause 20.1.4
P
14.3.1
Transformers and inductors marked with
manufacturer's name and type ......................... :
manufacturer's name and type ......................... :
Transtec TT0869803320 alt.
TT0869803320-E
TT0869803320-E
P
Transformers and inductors separately
approved ............................................................ :
approved ............................................................ :
No
N/A
14.3.2
General
14.3.3
Constructional requirements (complete
appended tables or include manufacturers
constructional insulation descriptions)
appended tables or include manufacturers
constructional insulation descriptions)
P
14.3.3.1
Clearances and creepage distances comply
with clause 13
with clause 13
P
14.3.3.2
Transformers meet the constructional
requirements
requirements
P
14.3.4.1
Class II transformers have adequate separation
between hazardous live parts and accessible
parts (double or reinforced insulation)
between hazardous live parts and accessible
parts (double or reinforced insulation)
Prim.-sec: 8.1mm
P
Click on the first or last page to see other HKTS 7 (serv.man3) service manuals if exist.