Harman Kardon HKTS 200SUB (serv.man2) EMC - CB Certificate ▷ View online
Page 8 of 89
Report No.: 17029429 001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
3
General requirements
P
Safety class of the apparatus ................................: Class II
P
4
General test conditions
P
4.1.4
Ventilation instructions require the use of the test
box
box
Not used
N/A
5
Marking and instructions
P
Comprehensible and easily discernible
The rating label is easily
discernible
discernible
P
Permanent durability against water and petroleum
spirit
spirit
Compliance was checked by
rubbing the marking by hand
for 15 s with cloth soaked with
water and cloth soaked with
petroleum spirit, it was not
possible to remove marking
plate and no curling observed
after the test
rubbing the marking by hand
for 15 s with cloth soaked with
water and cloth soaked with
petroleum spirit, it was not
possible to remove marking
plate and no curling observed
after the test
P
5.1
a) Identification, maker ........................................ : Identification mark:
P
b) Model number or type reference ....................... : HKTS200SUB
P
c) Class II symbol if applicable ............................. :
Marked on rear panel of
subwoofer
P
d) Nature of supply ............................................... : ~
P
e) Rated supply voltage ....................................... : 100-120V~ or 220-240V~,
indication on PCB for the set
voltage by CN2
voltage by CN2
P
f) Mains frequency if safety dependant ................. : 50/60Hz
P
g) Rated current or power consumption for
apparatus supplied by supply apparatus for general
use ..................................................................... :
apparatus supplied by supply apparatus for general
use ..................................................................... :
N/A
Measured current or power consumption ............. :
N/A
Deviation % (max 10%) ....................................... :
N/A
h) Rated current or power consumption for apparat-
us intended for connection to an a.c. mains supply :
us intended for connection to an a.c. mains supply :
200W
P
Measured current or power consumption ............. : (see appended table 7.1)
P
Measured current or power consumption for
Television set ...................................................... :
Television set ...................................................... :
N/A
Deviation % (max 10%) ....................................... : (see appended table 7.1)
P
5.2
a) Earth terminal
Class II apparatus
N/A
b) Hazardous live terminals
N/A
Page 9 of 89
Report No.: 17029429 001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
c) Markings on supply output terminals
N/A
5.3
a) Use of triangle with exclamation mark
Marked on the circuit diagram
P
b) marking on loudspeaker grille, IEC 60417-5036
N/A
5.4
Instructions for use
English & French
(Version in other language will
be provided when submitted
for national approval)
(Version in other language will
be provided when submitted
for national approval)
P
5.4.1
a) Mains powered equipment not exposed to
dripping or splashing. Warning concerning objects
filled with liquid, etc.
dripping or splashing. Warning concerning objects
filled with liquid, etc.
Indoor use only and warning
mentioned in user manual
mentioned in user manual
P
b) Hazardous live terminals, instructions for wiring
No such terminals.
N/A
c) Instructions for replacing lithium battery
N/A
d) Class I earth connection warning
Class II apparatus
N/A
e) Instructions for multimedia system connection
P
f) Special stability warning for attachment of the
apparatus to the floor/wall
apparatus to the floor/wall
N/A
g) Warning: battery exposure to heat
N/A
h) Warning: protective film on CRT face
N/A
5.4.2
a-b) Disconnect device: plug/coupler or all-pole
mains switch location, accessibility and markings
mains switch location, accessibility and markings
Mains plug on non-detachable
power cord used as disconnect
device and user manual
provided regarding being
readily operable
power cord used as disconnect
device and user manual
provided regarding being
readily operable
P
c) Instructions for permanently connected equipment No such equipment
N/A
Marking, signal lamps or similar for completely
disconnection from the mains
disconnection from the mains
N/A
6
Hazardous radiation
N/A
6.1
Ionizing radiation < 36 pA/kg (0,5 mR/h)
No such device
N/A
Ionizing radiation under fault condition
N/A
6.2
Laser radiation, emission limits to IEC 60825-1:2007
............................................................................:
............................................................................:
No laser, only optical port used
for optical input.
for optical input.
N/A
Emission limits under fault conditions ....................:
N/A
7
Heating under normal operating conditions
P
7.1
Temperature rises not exceeding specified values;
fuse links and other protective devices defeated
fuse links and other protective devices defeated
(see appended table 7.1)
P
7.1.1
Temperature rise of accessible parts
(see appended table 7.1)
P
7.1.2
Temperature rise of parts providing electrical
insulation
insulation
(see appended table 7.1)
P
Page 10 of 89
Report No.: 17029429 001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
7.1.3
Temperature rise of parts acting as a support or as a
mechanical barrier
mechanical barrier
(see appended table 7.1)
P
7.1.4
Temperature rise of windings
(see appended table 7.1)
P
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
N/A
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
o
C
Bobbin of switching isolating
transformers TR1, TR2 and
TR3 made from phenolic
material and considered to be
sufficient in regard to the
temperature characteristic (150
transformers TR1, TR2 and
TR3 made from phenolic
material and considered to be
sufficient in regard to the
temperature characteristic (150
C). see appended table 7.2
only for bobbin of Line Filter
LF2.
LF2.
P
8
Constructional requirements with regard to the protection against electric
shock
shock
P
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
untreated textile oxide films and beads etc.
considered to be bare
No such material
N/A
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
device, fuse-links or handling drawers etc.
It is not possible for user to
access fuse-link. No user or
service accessible voltage
setting device. No such
indicators or drawers
access fuse-link. No user or
service accessible voltage
setting device. No such
indicators or drawers
P
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
hygroscopic material
168h, 40°C, RH 93% (for wood
material by client request)
material by client request)
P
8.4
No risk of electric shock from accessible parts or
from parts rendered accessible following the
removal of a cover which can be removed by hand
from parts rendered accessible following the
removal of a cover which can be removed by hand
No such cover which can be
removed by hand
removed by hand
N/A
8.5
Class I equipment
Class II apparatus
N/A
Basic insulation between hazardous live parts and
earthed accessible parts
earthed accessible parts
N/A
Resistors bridging basic insulation complying with
14.1 a)
14.1 a)
N/A
Capacitors bridging basic insulation complying with
14.2.1 a)
14.2.1 a)
N/A
Protective earthing terminal
N/A
8.6
Class II equipment and Class II constructions within
Class I equipment
Class I equipment
Class II equipment
P
Double or reinforced insulation between hazardous
live parts and accessible parts
live parts and accessible parts
Reinforced or double insulation
used between hazardous live
parts and accessible parts
used between hazardous live
parts and accessible parts
P
Components bridging double or reinforced insulation
complying with 14.1 a) or 14.3
complying with 14.1 a) or 14.3
Switching isolating transformer
complied with clause 14.3
complied with clause 14.3
P
Page 11 of 89
Report No.: 17029429 001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
Basic insulation bridged by components complying
with 14.3.4.3.
with 14.3.4.3.
No such components
N/A
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.1 a)
bridged by a capacitor complying with 14.1 a)
No such capacitors
N/A
Double or reinforced insulation being bridged with 2
capacitors in series complying with 14.2.1 a)
capacitors in series complying with 14.2.1 a)
No such capacitors
N/A
Double or reinforced insulation being bridged with a
single capacitor complying with 14.2.1 b)
single capacitor complying with 14.2.1 b)
Approved Y1 capacitor bridged
between primary and
secondary circuits/metal
enclosure
between primary and
secondary circuits/metal
enclosure
(see appended table 14)
P
8.7
This clause is void
--
8.8
Basic or supplementary insulation > 0,4 mm (mm) :
Thickness of transformer
bobbin, see appended table 14
bobbin, see appended table 14
P
Reinforced insulation > 0,4 mm (mm) ...................:
See appended table 14 for
below information:
below information:
- thickness of enclosure
P
Thin sheet insulation (excluding non-separable thin
sheet insulation. See 8.22)
sheet insulation. See 8.22)
P
Basic or supplementary insulation, at least two
layers, each meeting 10.3
layers, each meeting 10.3
N/A
Basic or supplementary insulation, three layers any
two of which meet 10.3
two of which meet 10.3
N/A
Reinforced insulation, two layers each of which meet
10.3
10.3
N/A
Reinforced insulation, three layers any two which
meet 10.3
meet 10.3
(see appended table 10.3 and
clause 8.17)
clause 8.17)
P
8.9
Adequate insulation between internal hazardous live
conductors and accessible parts
conductors and accessible parts
Double/reinforced insulation
between primary live parts and
accessible parts
between primary live parts and
accessible parts
P
Adequate insulation between internal hazardous live
parts and conductors connected to accessible parts
parts and conductors connected to accessible parts
Basic insulated secondary
wires cannot touch hazardous
live parts, wire near to primary
side of power board already
fixed by ties.
wires cannot touch hazardous
live parts, wire near to primary
side of power board already
fixed by ties.
P
8.10
Double insulation between conductors connected to
the mains and accessible parts.
the mains and accessible parts.
P
Double insulation between internal hazardous live
parts and conductors connected to accessible parts.
parts and conductors connected to accessible parts.
P
8.11
Detaching of wires
P
Click on the first or last page to see other HKTS 200SUB (serv.man2) service manuals if exist.