Harman Kardon HK 990 (serv.man4) EMC - CB Certificate ▷ View online
Page 36 of 50
Report No. 902952-1
IEC
60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No.: IEC60065F
TRF Originator: ASTA BEAB
14.4.3
High voltage component part flame test
N/A
14.4.4
High voltage isolating component test
N/A
14.5.1.1
Thermal cut-outs comply with UL 873, UL 8730-2-9 or
UL 60730-2-9
UL 60730-2-9
N/A
14.5.1.2
Thermal links comply with UL 60691
P
14.5.1.3 Deleted
N/A
14.5.2.1
Fuse links comply with UL 248-14
P
14.5.2.2
Reference to IEC 60127 is deleted
P
Pre-arcing time/current characteristic and breaking
capacity marking requirements are deleted
capacity marking requirements are deleted
UL recognized fuse used
P
14.5.3
As an alternative, a PTC thermistor may comply with
requirements of UL 1434
requirements of UL 1434
N/A
14.5.4
Reference to fuse-links is deleted
P
Other protective devices directly connected to the
mains have adequate breaking capacity and comply
with UL 873, UL 1416, UL 1417 or UL 2111
mains have adequate breaking capacity and comply
with UL 873, UL 1416, UL 1417 or UL 2111
N/A
14.6.1
Switches and relays comply with UL 1054, UL 61058-1
or UL 508
or UL 508
UL 508
P
Mains switch or relay are rated for the total rated
current consumption of the apparatus
current consumption of the apparatus
12A
P
Rating of a mains switch or relay in audio apparatus
intended for commercial use
intended for commercial use
N/A
14.6.2-4 Deleted
N/A
14.6.5
A switch or relay that controls a mains socket-outlet
have a rating equal to the rated current consumption of
the apparatus plus the current rating of the socket-
outlet
have a rating equal to the rated current consumption of
the apparatus plus the current rating of the socket-
outlet
N/A
14.6.6
Mains switches comply with (a), (b) or (c)
b)
N/A
Mains relay contacts comply with (a), (b) or (d)
P
A switch that controls a mains receptacle complies with
(b) and a relay that controls a mains receptacle
complies with (b) or (d)
(b) and a relay that controls a mains receptacle
complies with (b) or (d)
N/A
14.6.6a
Switch or relay contacts have current rating equal to or
greater than 1.414 times the inrush current of the
apparatus
greater than 1.414 times the inrush current of the
apparatus
TV rated
N/A
14.6.6b
Switch or relay is TV rated
TV-8
P
14.6.6c
Switch is located on the back of apparatus and is not
operable from a emote control
operable from a emote control
N/A
14.6.6d
Relay subjected to the Relay Endurance Test
N/A
14.6.6.1
Peak inrush current test
P
14.6.6.2 Relay
endurance
test
N/A
14.6.7
Double pole switch controlling a.c. and d.c. circuits
N/A
Page 37 of 50
Report No. 902952-1
IEC
60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No.: IEC60065F
TRF Originator: ASTA BEAB
14.7
The jointed test finger (Fig 14) is used to determine
accessibility and operation of the interlock
accessibility and operation of the interlock
N/A
14.10.1
Internal rechargeable and non-rechargeable batteries
that are replaceable by the user or skilled persons
additionally comply with 14.10.2 – 14.10.5.
that are replaceable by the user or skilled persons
additionally comply with 14.10.2 – 14.10.5.
N/A
Test requirements from UL 2054 added for special
battery packs that are removable by the user from the
apparatus (Short circuit, Abnormal charging, Forced-
discharge, and 250-N steady force tests may be
carried separately from the apparatus)
battery packs that are removable by the user from the
apparatus (Short circuit, Abnormal charging, Forced-
discharge, and 250-N steady force tests may be
carried separately from the apparatus)
N/A
Note: Consumer grade, non-rechargeable carbon-zinc
or alkaline batteries are not subjected to the tests
specified in Clauses 14.10.2 – 14.10.5.
or alkaline batteries are not subjected to the tests
specified in Clauses 14.10.2 – 14.10.5.
N/A
14.10.5
Alternatively, one sample subjected to three drops
N/A
14.10.6
Location of overcurrent protective device
N/A
Alternatively, the overcurrent protective device in the
apparatus battery-supply circuit is not required if the
apparatus is to be connected to a vehicle power outlet
via UL 2089 vehicle battery adapter
apparatus battery-supply circuit is not required if the
apparatus is to be connected to a vehicle power outlet
via UL 2089 vehicle battery adapter
N/A
14.11
Component power supplies and their optocouplers
complying with UL 1310, UL 1950 Third Edition, or UL
60950 are considered to fulfill the clause.
complying with UL 1310, UL 1950 Third Edition, or UL
60950 are considered to fulfill the clause.
N/A
Optocouplers comply with UL 1577
N/A
Optocouplers bridging reinforced insulation comply with
requirements for double protection as specified in UL
1577
requirements for double protection as specified in UL
1577
N/A
External clearances and creepage distances of
optocouplers comply with 13.1
optocouplers comply with 13.1
N/A
14.12
Reference to IEC 61051-2 replaced by UL 1449
N/A
Reference to IEC 60707 replaced by UL 94
N/A
All references to IEC 60151 are deleted
N/A
15.1.1
Attachment plug current rating (no less than 125% of
the current drawn under normal operating conditions)
and voltage rating
the current drawn under normal operating conditions)
and voltage rating
10A
P
Configuration and electrical rating of an attachment
plug for apparatus for use on more than one supply
voltage by means of a voltage selector
plug for apparatus for use on more than one supply
voltage by means of a voltage selector
P
Polarized attachment plug
P
Wire gauge of conductors and internal wiring
connecting mains socket-outlets
connecting mains socket-outlets
N/A
15.1.3.1
Means of output connections on an audio amplifier
having an opencircuit audio output voltage not limited
to 120 V that is permanently connected to the mains
having an opencircuit audio output voltage not limited
to 120 V that is permanently connected to the mains
N/A
Quick
Connect
Terminals:
N/A
a) Male tabs firmly mounted in place;
N/A
b) Mating female connectors provided with the
apparatus;
apparatus;
N/A
Page 38 of 50
Report No. 902952-1
IEC
60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No.: IEC60065F
TRF Originator: ASTA BEAB
c) Strain Relief Test of Clause 16.5;
N/A
d) Installation instructions provided for assembly of
terminal to a conductor and strain relief
terminal to a conductor and strain relief
N/A
e) Terminals are appropriate for use with the size and
type of wire specified
type of wire specified
N/A
15.1.3.2
Audio amplifiers having an audio output not limited to
120 V that are connected to the mains by a flexible
cord
120 V that are connected to the mains by a flexible
cord
N/A
15.2
Cross-sectional area of the earthing conductor in a
supply cord or in an interconnecting cable
supply cord or in an interconnecting cable
N/A
Earthing conductors may have green or green/yellow
insulation
insulation
N/A
15.3.5
Reference to IEC 60950 is replaced by Article 310 of
the National Electrical Code, ANSI/NFPA 70
the National Electrical Code, ANSI/NFPA 70
P
Table 15 - "AWG" replace mm2 values
16AWG/2C
P
15.4
Component power supply adaptors complying with UL
1310, UL 1950 Third Edition, or UL 60950 fulfill the
clause
1310, UL 1950 Third Edition, or UL 60950 fulfill the
clause
N/A
16.1
Reference in the first paragraph to “sheathed” flexible
cords Is deleted
cords Is deleted
P
References to IEC 60227 and IEC 60245 deleted
P
Ampacity and VW-1 marking of mains supply flexible
cords
cords
P
Table 17A - Cords for apparatus
P
16.2
Power supply cord earthing conductor size
P
Reference to IEC 60950, Table 3B is replaced by
Article 400 of the National Electrical Code
Article 400 of the National Electrical Code
P
Table 18 - Upper current limit in column 1 increased
from 16 to 30 A and "AWG" wire sizes
from 16 to 30 A and "AWG" wire sizes
P
16.3
c) Flexible cords not complying with 16.1, used as
connection between the apparatus and other apparatus
are marked VW-1
connection between the apparatus and other apparatus
are marked VW-1
N/A
16.5
When polymeric materials are involved, strain and twist
testing is to be conducted before and after the sub-
clause 12.1.5 stress relief test.
testing is to be conducted before and after the sub-
clause 12.1.5 stress relief test.
N/A
17.8
Expanded to include all cart/stand parts supplied by
themanufacturer, such as casters and brackets.
Suitable assembly instructions are required.
themanufacturer, such as casters and brackets.
Suitable assembly instructions are required.
N/A
Relevant fixing means are not required when
installation is to be done by a skilled person
installation is to be done by a skilled person
N/A
17.10
Termination of aluminum conductors used as internal
wiring
wiring
N/A
Page 39 of 50
Report No. 902952-1
IEC
60065
Clause
Requirement – Test
Result - Remark
Verdict
TRF No.: IEC60065F
TRF Originator: ASTA BEAB
17.11
An accessory was investigated to determine that: a).
The accessory, and the combination of the accessory
and the apparatus presents no hazard in the sense of
this standard, and
The accessory, and the combination of the accessory
and the apparatus presents no hazard in the sense of
this standard, and
b). The accessory is provided with installation
instructions.
instructions.
N/A
17.11.1
Installation of an accessory by a skilled person:
a) The mechanical positioning is accomplished by
means of tools normally available or by means of
special tools provided as part of the installation kit,
means of tools normally available or by means of
special tools provided as part of the installation kit,
N/A
b) The electrical connections are made by using
existing terminals and connections in the apparatus or
the building wiring
existing terminals and connections in the apparatus or
the building wiring
N/A
18
Non-intrinsically protected picture tubes comply with
18.1, 18.2.2 and 18.3. Intrinsically protected picture
tubes with a maximum face dimension exceeding 7.5
cm comply with UL 61965.
18.1, 18.2.2 and 18.3. Intrinsically protected picture
tubes with a maximum face dimension exceeding 7.5
cm comply with UL 61965.
N/A
A bulb of a picture tube having a face diameter of 7.5
cm or more are mounted in an enclosure
cm or more are mounted in an enclosure
N/A
Enclosure opening dimensions
N/A
18.1
All tubes are mounted such that the enclosure of the
apparatus protects the tube against the effects of
implosion.
apparatus protects the tube against the effects of
implosion.
N/A
18.2
Clauses 18.2, 18.2.1 and 18.2.3 are deleted
N/A
19
The tests in 19.1, 19.2 and 19.3 do not cause the
apparatus to overturn.
apparatus to overturn.
N/A
The test in 19.2.1 does not cause the apparatus to
slide
slide
N/A
When polymeric materials are involved, testing is to be
conducted before and after the sub-clause 12.1.5
stress relief test.
conducted before and after the sub-clause 12.1.5
stress relief test.
N/A
19.1
References to an apparatus in combination with a
supplied cart or recommended stand are deleted
supplied cart or recommended stand are deleted
N/A
19.2
References to an apparatus in combination with a
supplied cart or recommended stand are deleted
supplied cart or recommended stand are deleted
N/A
19.2.1 Slide
test
N/A
19.3
Horizontal force stability test using Table 20A values
from UL 60065
from UL 60065
N/A
19.5
Reference to the impact hammer in the first compliance
paragraph is deleted
paragraph is deleted
N/A
19.6
Equipment rack mounting test
N/A
20.1a Deleted
N/A
20.1b
Exception for parts such as protection TV lenses,
loudspeaker parts, external accessories, and fibrous
materials
loudspeaker parts, external accessories, and fibrous
materials
N/A
Reference to IEC 60707 replaced by UL 94
N/A
Click on the first or last page to see other HK 990 (serv.man4) service manuals if exist.