Harman Kardon GO AND PLAY (serv.man4) EMC - CB Certificate ▷ View online
- Page 12 of 58 -
www.nemko.com
Report No. 70512
TRF No.:IECEN60950_1B
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
1.5.8
Components in equipment for IT power systems
Class III equipment.
N/A
1.6 Power
interface
P
1.6.1
AC power distribution systems
Class III equipment.
N/A
1.6.2
Input current
Refer to appended table 1.6.2.
P
1.6.3
Voltage limit of hand-held equipment
The equipment is not hand-
held.
held.
N/A
1.6.4
Neutral conductor
Class III equipment.
N/A
1.7 Markings
and
instructions
P
1.7.1
Power rating
Marking not required, however
the marking is located on the
outside surface of the
equipment.
the marking is located on the
outside surface of the
equipment.
P
Rated voltage(s) or voltage range(s) (V) ........... : 18Vdc
P
Symbol for nature of supply, for d.c. only ........... : IEC 60417-1, symbol No. 5031,
is used.
P
Rated frequency or rated frequency range (Hz) : DC rated.
N/A
Rated current (mA or A) ..................................... : 3.3A
P
Manufacturer’s name or trademark or
identification mark .............................................. :
identification mark .............................................. :
P
Type/model or type reference ............................. : Go+Play
P
Symbol for Class II equipment only ................... : The equipment is Class III.
N/A
Other symbols .................................................... : The additional marking does
not give rise to
misunderstandings.
misunderstandings.
P
Certification marks ............................................. : Refer to copy of markings.
P
1.7.2
Safety instructions
Provided with marking
regarding use of specified
power supply (Not required),
refer to Copy of marking plate.
regarding use of specified
power supply (Not required),
refer to Copy of marking plate.
N/A
1.7.3
Short duty cycles
The equipment is intended for
continuous operation.
continuous operation.
N/A
1.7.4
Supply voltage adjustment ................................. : No voltage selector.
N/A
1.7.5
Power outlets on the equipment ........................ : No standard power outlet.
N/A
1.7.6 Fuse
identification
.............................................. :
No
fuses.
N/A
1.7.7
Wiring terminals
Class III equipment.
N/A
- Page 13 of 58 -
www.nemko.com
Report No. 70512
TRF No.:IECEN60950_1B
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
1.7.7.1
Protective earthing and bonding terminals ........ :
N/A
1.7.7.2
Terminal for a.c. mains supply conductors
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
N/A
1.7.8
Controls and indicators
Refer below:
P
1.7.8.1
Identification, location and marking ................... : No controls or figures affecting
safety provided.
N/A
1.7.8.2
Colours ............................................................... : No controls or indicators us
color.
N/A
1.7.8.3
Symbols ............................................................ : There are no switches in the
equipment. Control is marked
with “+” and “-“.
with “+” and “-“.
P
1.7.8.4
Markings using figures ...................................... : Refer to Copy of marking, the
manufacturer includes
explanation of graphic symbols
in the instruction manual.
explanation of graphic symbols
in the instruction manual.
P
1.7.9
Isolation of multiple power sources .................... : Class III equipment.
N/A
1.7.10
IT power distribution systems
Class III equipment.
N/A
1.7.11
Thermostats and other regulating devices
No thermostats or other
regulating devices.
regulating devices.
N/A
1.7.12
Language ........................................................... : Instructions and markings shall
be in a language acceptable for
the country where the
equipment is to be sold.
English manual verified.
the country where the
equipment is to be sold.
English manual verified.
—
1.7.13 Durability
The
marking withstands
required tests.
P
1.7.14
Removable parts
No removable parts, except
batteries.
batteries.
P
1.7.15
Replaceable batteries
Normal D-cell batteries to be
used in the equipment.
(See summary of testing).
used in the equipment.
(See summary of testing).
P
Language ............................................................ :
—
1.7.16
Operator access with a tool ................................ : No hazardous voltages or
energy levels in the equipment
in normal or single fault
condition.
(See appended table 5.3)
in normal or single fault
condition.
(See appended table 5.3)
P
1.7.17
Equipment for restricted access locations .......... : Equipment not intended for
installation in RAL.
N/A
- Page 14 of 58 -
www.nemko.com
Report No. 70512
TRF No.:IECEN60950_1B
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
2
PROTECTION FROM HAZARDS
N/A
2.1
Protection from electric shock and energy hazards
N/A
2.1.1
Protection in operator access areas
Refer below:
N/A
2.1.1.1
Access to energized parts
Class III equipment.
Output from the external PSU is
considered to be below 240VA
(Energy from batteries are
below 240VA)
(See appended table 2.1.1.5
c1)
Output from the external PSU is
considered to be below 240VA
(Energy from batteries are
below 240VA)
(See appended table 2.1.1.5
c1)
N/A
Test by inspection ..............................................:
N/A
Test with test finger ............................................:
N/A
Test with test pin ................................................:
N/A
Test with test probe ............................................:
N/A
2.1.1.2
Battery compartments ........................................: No TNV circuits in the
equipment.
N/A
2.1.1.3
Access to ELV wiring
No internal wiring at ELV.
N/A
Working
voltage
(V);
minimum distance (mm)
through insulation
—
2.1.1.4
Access to hazardous voltage circuit wiring
Class III equipment.
N/A
2.1.1.5
Energy hazards ..................................................: Class III equipment.
The external SELV source is
considered to be below 240VA
(Energy from batteries are
below 240VA)
considered to be below 240VA
(Energy from batteries are
below 240VA)
N/A
2.1.1.6
Manual controls
No shafts or knobs.
N/A
2.1.1.7
Discharge of capacitors in equipment
Class III equipment.
N/A
Time-constant (s); measured voltage (V) ...........:
—
2.1.2
Protection in service access areas
Class III equipment.
N/A
2.1.3
Protection in restricted access locations
Equipment not intended for
installation in RAL.
installation in RAL.
N/A
2.2 SELV
circuits
P
2.2.1
General requirements
SELV limits are not exceeded
under normal condition and
after a single fault. Equipment
is powered from a SELV
source.
under normal condition and
after a single fault. Equipment
is powered from a SELV
source.
P
- Page 15 of 58 -
www.nemko.com
Report No. 70512
TRF No.:IECEN60950_1B
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
2.2.2
Voltages under normal conditions (V).................: Powered by SELV source.
P
2.2.3
Voltages under fault conditions (V) .....................: Powered by SELV source.
P
2.2.3.1
Separation by double insulation or reinforced
insulation (method 1)
insulation (method 1)
N/A
2.2.3.2
Separation by earthed screen (method 2)
N/A
2.2.3.3
Protection by earthing of the SELV circuit
(method 3)
(method 3)
N/A
2.2.4
Connection of SELV circuits to other circuits....... : SELV circuits are only
connected to other SELV
circuits and protective earth.
circuits and protective earth.
P
2.3 TNV
circuits
N/A
2.3.1 Limits
No
TNV
circuits.
N/A
Type of TNV circuits............................................:
—
2.3.2
Separation from other circuits and from
accessible parts
accessible parts
N/A
Insulation
employed ............................................:
—
2.3.3
Separation from hazardous voltages
N/A
Insulation
employed ............................................:
—
2.3.4
Connection of TNV circuits to other circuits
N/A
Insulation
employed ............................................:
—
2.3.5
Test for operating voltages generated externally
N/A
2.4 Limited
current
circuits
P
2.4.1
General requirements
Bridging capacitor (Y1) across
insulation in the specified
external power supply (See
copy of marking plate).
insulation in the specified
external power supply (See
copy of marking plate).
P
2.4.2 Limit
values
49mA,
73.7nF
P
Frequency
(Hz) ................................................... :
70kHz
—
Measured current (mA) ....................................... : 1.8mA peak
—
Measured voltage (V).......................................... : 610Vp
—
Measured capacitance (
µF) ................................ : 3300pF
—
Click on the first or last page to see other GO AND PLAY (serv.man4) service manuals if exist.