DOWNLOAD Sony SLV-D300P (serv.man2) Service Manual ↓ Size: 13.67 MB | Pages: 123 in PDF or view online for FREE

2-17

1) Remove the screw 1.
2) Lift the FE Head 2.

Fig. 2-34 FE Head Removal

1) Pull out the FPC from connector of ACE Head Ass’y 2.
2) Remove the screw 1.
3) Lift the ACE Head Ass’y 2.

Fig. 2-35 ACE Head Removal

1

FE HEAD

1

SCREW

2

HEAD ACE ASS`Y

2-18

1) Move the Slider S, T Ass’y 1, 2 to slot, and then lift it to remove.

(Refer to arrow)

Fig. 2-36 Slider S, T Ass’y Removal

1) Remove the 3 Screws 1.
2) Lift the Plate Ground Deck 2.
3) Lift the Cylinder Ass’y 3.

1) Match the 3 holes in the bottom of Cylinder Ass’y 3  to the 3

holes of Main Base as attending not to drop or knock the Cylinder
Ass’y 3.

2) Tighten the 1 Screw 1.
3) Match the Plate Ground Deck 2 to the Hole of Base Main.
4) Tighten the other 2 Screws 1.

1) Take care not to touch the Cylinder Ass’y 3 and the tape guide

post at reinstalling.

2) When reinstalling, Don't push down too much on Screw Driver.

Fig. 2-37 Plate Ground Deck, Cylinder Ass’y Removal

1

SLIDER S ASS`Y

2

SLIDER T ASS`Y

1

3 SCREWS

2

PLATE GROUND DECK

3

CYLINDER ASS'Y

2-19

1) Remove the Belt Pulley 1.

  Take extreme care not to get grease on Belt Pulley 1  at

assembling or reassembling.

Fig. 2-38 Belt Pulley Removal

1) Remove the Damper Capstan 1 in the direction
of arrow.
2) Remove the 3 Screws 2.
3) Remove the Motor Capstan Ass’y 3.

1) Match the 3 holes of Motor Capstan Ass’y 3 to the 3 holes of

Main Base. Be careful not to drop or knock the Motor Capstan
Ass’y 3.

2) Tighten the 3 Screws 2 in the direction of arrow as shown detail

drawing.

3) Assemble the Damper Capstan 1.

 After tightening screws, check if there is gap between the head

of screws and the top side of Main Base. There should have no gap
between the head of screws and the top side of Main Base.
After reinstalling, adjusting the tape transport
system again.

Fig. 2-39 Motor Capstan Ass’y Removal

1

BELT PULLEY

1

3 SCREWS

2

MOTOR CAPSTAN ASS'Y

2-20

1) Rotate the Post #8 Guide Ass’y 1 in the direction of arrow to lift

up.

Fig. 2-40 Post #8 Guide Ass’y Removal

1) Release the Hook 1.
2) Lift the Lever Head Cleaner Ass’y 2.

Fig. 2-41 Lever Head Cleaner Ass’y Removal

1) Turn the Gear worm 1  clockwise with screw driver.(Refer to

arrow)
(Other method: Remove the Screw of Motor Load Ass’y, Separate
the Motor Load Ass’y)

Fig. 2-42

2) When Slider S,T are approched in the position of unloading, rotate

holder Clutch counterclockwise after inserting screw driver in the
hole of frame's bottom in order to wind the unwinded tape.
(Refer to Fig.2-43)
(If you rotate Gear Worm 1 continuously when tape is in state of
unwinding, you may cause a tape contamination by grease and
tape damage.
Be sure to wind the unwinded tape in the state of set horizently.)

3) Rotate Gear Worm 1 clockwise using screw driver again up to

the state of eject mode and then pick out the tape.(Refer to Fig.2-
42)

Fig. 2-43

1

POST #8 GUIDE ASS'Y

1

HOOK

2

LEVER HEAD CLEANER ASS'Y

SLEEVE-HEAD CLEANER

1

GEAR WORM

FRAME