DOWNLOAD Sony SLV-D300P (serv.man2) Service Manual ↓ Size: 13.67 MB | Pages: 123 in PDF or view online for FREE

2-13

1) Release the Hook [A] and the Hook [B], [C] in the direction of

arrow as shown in Fig 2-25.

2) Lift the Lever S, T Brake Ass’y 1, 2 with spring brake 3.

1) Assembly the Lever S Brake Ass’y 1 on the Main Base.
2) Assembly the Lever T Brake Ass’y 2 with spring brake 3.

 Take extreme care not to be folded and

transformed Spring Brake at removing or reinstalling.

Fig. 2-25 Lever Brake S, T Ass’y Removal

1) Push the Lever Idle 1 in the direction of arrow “A”, “B”.
2) Lift the Lever Idle 1.

Assembly :
1) Apply oil in two Bosses of Lever Idle 1.
2) Assemble the Gear Idle 2 with the Lever Idle 1.

 When replacing the Gear Idle 2, be sure to add oil in the boss

of Lever Idle 1.

Fig. 2-26 Gear Idle Ass’y Removal

1

LEVER S BRAKE ASS'Y

2

LEVER T BRAKE ASS`Y

3

SPRING BRAKE

HOOK(B)

HOOK(C)

HOOK(A)

2

GEAR IDLE

2

GEAR IDLE

1

LEVER IDLE

"A"

HOOK "C"

"B"

2-14

1) Lift the Disk S, T Reel 1, 2.

Fig. 2-27 Disk S, T Reel Removal

1) Remove the Washer Slit 1.
2) Lift the Holder Clutch Ass’y 2.

Note: When you reinstall Holder Clutch Ass’y
1) Check the condition of spring as shown in detail A.
2) Don't push Holder Clutch Ass’y down with excessive force Just

insert Holder Clutch Ass’y into post center with dead force and
Rotate it smoothly.
Be sure to confirm that spring is in the slit of Gear Center Ass’y as
shown in detail B.

Fig. 2-28 Holder Clutch Ass’y Removal

1

DISK S REEL

2

DISK T REEL

1

WASHER SLIT

2

HOLDER CLUTCH ASS`Y

DETAIL  A

<BAD>

SPRING

<GOOD>

<BAD>

SPRING

<GOOD>

DETAIL  B

2-15

1) Remove the 2 hooks in the direction of arrow as shown Fig. 2-28

and lift the Lever Up Down Ass’y 1.

2) Lift the Gear Center Ass’y 2.

1) Insert the Lever Up Down Ass’y 1 in the rectangular holes on

Main Base as shown in Fig 5-30.

2) Lift the Lever Up Down Ass’y 1 about 35

°.

    (Refer to Fig 2-30)
3) Insert Ring of the Gear Center Ass’y 2 in the Guide of the Lever

Up Down Ass’y 1.

4) Insert the Gear Center Ass’y 2 in the post on Main Base.
5) Push down the Lever Up Down Ass’y 1 for locking of the Hook.

1) Take care not to separate and sentence does not mark sense.
2) Be sure to confirm that Ring of the Gear Center Ass’y 2 is in the

Guide of the Lever Up Down Ass’y 1 after finishing assembly of
Lever Up Down Ass’y 1 and Gear Center Ass’y 2.

Fig. 2-29 Lever Up Down Ass’y Removal

Fig. 2-30 Lever Up Down Ass’y Removal

1) Lift the Hook [A].
2) Rotate the Guide Cassette Door 1 in the direction of arrow.

 After reinstalling the Guide Cassette Door 1 sure the Hook

[A].

Fig. 2-31 Guide Cassette Door Removal

1

LEVER UP DOWN ASS`Y

2

GEAR CENTER ASS`Y

MAIN BASE

LEVER UP DOWN ASS'Y 

GUIDE

GEAR CENTER ASS'Y 

RING

GEAR
POST

HOOK

35

1

GUIDE CASSETTE DOOR

HOOK [A]

2-16

1) Lift the Unit Pinch Ass’y 1.
2) Remove the Plate Joint 2 from Lever Pinch Drive.
3) Remove the Spring Pinch Drive 3.

1) Take extreme care not to touch the grease on the Roller Pinch.
2) When reinstalling, be sure to apply grease on the post pinch roller.

Fig. 2-32 Lever Unit Pinch Ass’y, Plate Joint,

Spring Pinch Drive Removal

1) Remove the Spring #9 Guide 1.
2) Lift the Spring #9 Guide Ass’y 2 in the direction of arrow “A”.

1) Take extreme care not to get grease on the tape Guide Post.
2) After reinstalling, check the bottom side of the Post #9 Guide to

the top side of Main Base.

Fig. 2-33 Lever #9 Guide Ass’y Removal

3

SPRING PINCH DRIVE

1

LEVER UNIT PINCH ASS`Y

2

PLATE JOINT

1

SPRING #9 GUIDE

2

LEVER #9 GUIDE ASS`Y

"A"

"B"