Sony SLV-D271P / SLV-D370P (serv.man3) Service Manual ▷ View online
2-5
Fig. 2-9 Top Parts Location-2
1
FE HEAD
2
ASS’Y CYLINDER
3
ASS’Y ACE HEAD
4
ASS’Y LEVER UNIT PINCH
5
ASS’Y LEVER #9 GUIDE
6
ASS’Y LEVER TENSION
7
ASS’Y BAND BRAKE
8
DISK S REEL
9
ASS’Y LEVER S BRAKE
0
GEAR IDLE
qa
LEVER IDLE
qs
ASS’Y LEVER T BRAKE
qd
DISK T REEL
1
2
6
7
8
9
qa 0
qs
qd
0
3
4
5
2-6
2-3-2 Bottom View
Fig. 2-10 Bottom Parts Location
1
GEAR JOINT 1
2
GEAR JOINT 2
3
BRAKET GEAR
4
ASS’Y MOTOR CAPSTAN
5
ASS’Y LEVER T LOAD
6
GEAR LOADING DRIVE
7
ASS’Y LEVER S LOAD
8
ASS’Y CLUTCH
9
BELT PULLEY
0
SLIDER CAM
1
2
3
4
5
6
7
8
9
0
2-7
2-4 VCR DECK
2-4-1 Ass’y Holder Cassette Removal
1) Pull the Ass’y Holder Cassette 1 to the eject position.
2) Pull the Ass’y Holder Cassette 1 as grasping the Ass’y Holder
2) Pull the Ass’y Holder Cassette 1 as grasping the Ass’y Holder
Cassette 1 and Lever Lock2 in the same time to release hooking
from Main Base until the Boss [A] of Ass’y Holder Cassette 1
is taken out from the Rail [B].
from Main Base until the Boss [A] of Ass’y Holder Cassette 1
is taken out from the Rail [B].
3) Lift the Ass’y Holder Cassette 1, in this time, you have to grasp
the Lever Lock 2 Continuously until the Ass’y Holder Cassette
1 is taken out completely.
1 is taken out completely.
Note:
Be sure to insert Lever Lock 2 in the direction of “A” to
prevent separation and breakage of the Lever Lock 2 at
disassembling and reassembling.
disassembling and reassembling.
Fig. 2-11 Ass’y Holder Cassette Removal
2-4-2 Ass’y Lever Arm Removal
1) Push the hole “A” in the direction of arrow “B” use the pin.(about
Dia. 2.5)
2) Pull out the Ass’y Lever Arm 1 from the Boss of Main Base.
3) Remove the Ass’y Lever Arm 1 in the direction of arrow “C”.
3) Remove the Ass’y Lever Arm 1 in the direction of arrow “C”.
Fig. 2-12 Ass’y Lever Arm Removal
"A"
1
ASS'Y HOLDER
CASSETTEE
BOSS [A]
2
LEVER LOCK
RAIL [B]
PIN
HOLE "A"
1
ASS'Y LEVER ARM
"C"
"B"
2-8
2-4-4 Slider FL Drive, Gear FL Cam Removal
1) Pull the Slider FL Drive 1 to the front direction.
2) Remove the Slider FL Drive 1 in the direction of arrow. (Refer
2) Remove the Slider FL Drive 1 in the direction of arrow. (Refer
to Fig. 2-14)
3) Remove the Gear FL cam 2.
Note:
When reinstalling be sure to reassemble Slider FL drive 1
after you insert the Boss of Lever ARM-R in Groove of Slider FL
drive 1.
drive 1.
Assembly:
Align the Gear FL Cam 1 with the Gear worm wheel
Post as shown drawing.
(Refer to Timing point)
(Refer to Timing point)
Fig. 2-14 Slider FL Drive Removal
Fig. 2-15 Gear FL Cam, Gear Worm
2-4-3 Lever Door Removal
1) Release the Hook 2 and Remove the Lever Door 1 in the
direction of arrow “A”.
Fig. 2-13 Lever Door Removal
"B"
"C"
"A"
2
LEVER FL DOOR
1
SLIDER FL DRIVE
1
SLIDER FL DRIVE
2
GEAR FL CAM
2
GEAR FL CAM
GEAR WORM WHEEL
POST
TIMING POINT
Click on the first or last page to see other SLV-D271P / SLV-D370P (serv.man3) service manuals if exist.