Sony SLV-D271P / SLV-D370P (serv.man3) Service Manual ▷ View online
2-13
2-4-13 Ass’y Lever Brake S, T Removal
1) Release the Hook [A] and the Hook [B], [C] in the direction of
arrow as shown in Fig 2-25.
2) Lift the Ass’y Lever S, T Brake 1, 2 with spring brake 3.
Assembly:
1) Assembly the Ass’y Lever S Brake 1 on the Main Base.
2) Assembly the Ass’y Lever T Brake 2 with spring brake 3.
2) Assembly the Ass’y Lever T Brake 2 with spring brake 3.
Note:
Take extreme care not to be folded and
transformed Spring Brake at removing or reinstalling.
Fig. 2-25 Ass’y Lever Brake S, T Removal
2-4-14 Ass’y Gear Idle Removal
1) Push the Lever Idle 1 in the direction of arrow “A”, “B”.
2) Lift the Lever Idle 1.
2) Lift the Lever Idle 1.
Assembly:
1) Apply oil in two Bosses of Lever Idle 1.
2) Assemble the Gear Idle 2 with the Lever Idle 1.
2) Assemble the Gear Idle 2 with the Lever Idle 1.
Note:
When replacing the Gear Idle 2, be sure to add oil in the
boss of Lever Idle 1.
Fig. 2-26 Ass’y Gear Idle Removal
HOOK(A)
1
ASS'Y
LEVER S BRAKE
3
SPRING BRAKE
2
ASS'Y LEVER T
BRAKE
HOOK(B)
HOOK(C)
"A"
1
LEVER IDLE
2
GEAR IDLE
HOOK "C"
2
GEAR IDLE
"B"
2-14
2-4-15 Disk S, T Reel Removal
1) Lift the Disk S, T Reel 1, 2.
Fig. 2-27 Disk S, T Reel Removal
2-4-16 Ass’y Holder Clutch Removal
1) Remove the Washer Slit 1.
2) Lift the Ass’y Holder Clutch 2.
2) Lift the Ass’y Holder Clutch 2.
Note:
When you reinstall Ass’y Holder Clutch.
1) Check the condition of spring as shown in detail A.
2) Don't push Ass’y Holder Clutch down with excessive force Just
2) Don't push Ass’y Holder Clutch down with excessive force Just
insert Holder Clutch Ass’y into post center with dead force and
Rotate it smoothly.
Be sure to confirm that spring is in the slit of Ass’y Gear Center
as shown in detail B.
Rotate it smoothly.
Be sure to confirm that spring is in the slit of Ass’y Gear Center
as shown in detail B.
Fig. 2-28 Ass’y Holder Clutch Removal
1
WASHER SLIT
2
ASS
'
Y CLUTCH
DETAIL A
<BAD>
SPRING
<GOOD>
<BAD>
SPRING
<GOOD>
DETAIL B
1
REEL S
2
REEL T
2-15
1
GUIDE CASSETTE DOOR
HOOK [A]
2-4-17 Ass’y Lever Up Down, Ass’y Gear
Center Removal
1) Remove the 2 hooks in the direction of arrow as shown Fig. 2-
29 and lift the Ass’y Lever Up Down 1.
2) Lift the Ass’y Gear Center 2.
Assembly:
1) Insert the Ass’y Lever Up Down 1 in the rectangular holes on
Main Base as shown in Fig 2-30.
2) Lift the Lever Ass’y Up Down 1 about 35
°.
(Refer to Fig 2-30)
3) Insert Ring of the Ass’y Gear Center 2 in the Guide of the
3) Insert Ring of the Ass’y Gear Center 2 in the Guide of the
Ass’y Lever Up Down 1.
4) Insert the Ass’y Gear Center 2 in the post on Main Base.
5) Push down the Ass’y Lever Up Down 1 for locking of the Hook.
5) Push down the Ass’y Lever Up Down 1 for locking of the Hook.
Note:
1) Take care not to separate and sentence does not mark sense.
2) Be sure to confirm that Ring of the Ass’y Gear Center 2 is in
2) Be sure to confirm that Ring of the Ass’y Gear Center 2 is in
the Guide of the Ass’y Lever Up Down 1 after finishing
assembly of Ass’y Lever Up Down 1 and Ass’y Gear Center
2.
assembly of Ass’y Lever Up Down 1 and Ass’y Gear Center
2.
Fig. 2-29 Ass’y Lever Up Down Removal
Fig. 2-30 Ass’y Lever Up Down Removal
2-4-18 Guide Cassette Door Removal
1) Lift the Hook [A].
2) Rotate the Guide Cassette Door 1 in the direction of arrow.
2) Rotate the Guide Cassette Door 1 in the direction of arrow.
Note:
After reinstalling the Guide Cassette Door 1 sure the Hook
[A].
Fig. 2-31 Guide Cassette Door Removal
1
ASS'Y LEVER UP DOWN
2
ASS'Y GEAR CENTER
MAIN BASE
ASS'Y LEVER UP DOWN
GUIDE
ASS'Y GEAR CENTER
RING
GEAR
POST
POST
HOOK
35
2-16
"A"
"B"
2
ASS'Y LEVER #9 GUIDE
1
SPRING #9 GUIDE
2-4-19 Ass’y Lever Unit Pinch, Plate Joint,
Spring Pinch Drive Removal
1) Lift the Ass’y Unit Pinch 1.
2) Remove the Plate Joint 2 from Lever Pinch Drive.
3) Remove the Spring Pinch Drive 3.
2) Remove the Plate Joint 2 from Lever Pinch Drive.
3) Remove the Spring Pinch Drive 3.
Note:
1) Take extreme care not to touch the grease on the Roller Pinch.
2) When reinstalling, be sure to apply grease on the post pinch
roller.
2) When reinstalling, be sure to apply grease on the post pinch
roller.
Fig. 2-32 Ass’y Lever Unit Pinch, Plate Joint,
Spring Pinch Drive Removal
2-4-20 Ass’y Lever #9 Guide Removal
1) Remove the Spring #9 Guide 1.
2) Lift the Ass’y Spring #9 Guide 2 in the direction of arrow “A”.
2) Lift the Ass’y Spring #9 Guide 2 in the direction of arrow “A”.
Note:
1) Take extreme care not to get grease on the tape Guide Post.
2) After reinstalling, check the bottom side of the Post #9 Guide to
2) After reinstalling, check the bottom side of the Post #9 Guide to
the top side of Main Base.
Fig. 2-33 Ass’y Lever #9 Guide Removal
1 ASS'Y LEVER
UNIT PINCH
2
PLATE JOINT
3
SPRING PINCH
DRIVE
Click on the first or last page to see other SLV-D271P / SLV-D370P (serv.man3) service manuals if exist.