DOWNLOAD Sony JMECHA Service Manual ↓ Size: 1.29 MB | Pages: 41 in PDF or view online for FREE

— 5 —

Tape running surface cleaning

Rotary drum cleaning and
degaussing

Capstan bearing

Loading motor

Abnormal sound

Back-tension measurement

Brake system

Brake system

FWD/RVS torque measurement

500

a

a

—

—

✩

—

—

—

—

1000

a

a

✩
✩
✩
✩
✩
✩
✩

1500

a

a

—

—

✩

—

—

—

—

2000

a

a

✩
✩
✩
✩
✩
✩
✩

2500

a

a

—

—

✩

—

—

—

—

3000

a

a

✩
✩
✩
✩
✩
✩
✩

3500

a

a

—

—

✩

—

—

—

—

4000

a

a

✩
✩
✩
✩
✩
✩
✩

4500

a

a

—

—

✩

—

—

—

—

5000

a

a

✩
✩
✩
✩
✩
✩
✩

Be careful not to attach oil

Be careful not to attach oil

a: Cleaning, ✩: Check

When the machine is overhauled, replace the parts referring to the
above list.

Grease
• Be sure to use the specified grease only.  (If grease of different

viscosity is used, it can cause various troubles.)

• The grease used for bearings must not contain any dust or other

matter, otherwise  excessive abrasion and seizure of the bearing
could occur.

• A drop of grease means the amount of grease as shown in the

illustration, which is the amount that is attracted to the tip of a
rod of 2 mm diameter.

• FLOIL grease (SG-941): Part No. 7-662-001-39

— 6 —

J-1

J-2

J-3

J-4

J-5

J-6

J-7

J-8

J-9

J-10

J-11

J-12

J-13

J-14

J-15

J-16

Cleaning fluid

Wiping cloth

Super-fine applicator
(made by Nippon Applicator (P752D))

Mirror (small oval type)

Tracking tape (XH2-1) (NTSC, PAL)

Mini DV torque cassette

TG1 adjustment jig (FWD position adjustment)

TG1 FWD adjustment screwdriver

Dummy drum (for TG36) (J mechanism)

TG36 gauge

Torque screwdriver

Tape path screwdriver

Adjustment remote commander
(RM-95 upgraded) * Note 1

Mode Selector II

Mode Selector II conversion board (J)

Mode Selector II ROM (supporting J mechanism)
* Note 2

Y-2031-001-0

7-741-900-53

—

J-6080-840-A

8-967-997-01

J-6082-360-A

J-6082-492-A

J-6082-364-A

J-6082-490-A

J-6082-491-A

J-9049-330-A

J-6082-026-A

J-6082-053-B

J-6082-282-B

J-6082-493-A

J-6082-314-E

GD-2038

Tape path

Tape path

For TG1 FWD position adjustment

For tape path adjustment

General adjustment (ROM version 1.7)

ROM for Mode Selector II

 Oscilloscope

If the microprocessor in the adjustment remote commander is not
the new one  (UPD7503G-C56-12), the pages cannot be switched.
In this case, replace it with the new microprocessor (8-759-148-
35).

This is the ROM used for upgrading the version of Mode Selector
II to enable it to be used for the J mechanism.

— 7 —

— 8 —

The Mode Selector II is a mechanism drive tool that assists
maintenance work of the various mechanism decks.  It has the
following functions.

In this mode, the motor of the mechanism deck is powered only
during the period while the switch is turned on manually.  Using the
Manual Test, the operator can freely control the motor of the
mechanism deck.

In this mode, the motor of the mechanism deck is kept turned on
until the mechanical status is changed from the present mechanical
status that is obtained from the sensor information.  The Step Test is
used to confirm a series of movements of the mechanism deck.

The Mode Selector II stores the status transition table in its memory
as data indicating the respective modes of the mechanism deck.
The status transition table can be used to confirm whether a
mechanism deck is operating normally or has abnormality from a
series of movements of a mechanism deck.  If an abnormal status
transition is detected during operation, the “NG” indication appears
and the mechanism stops moving.

RVS

FF

SEL