DOWNLOAD Sony JMECHA Service Manual ↓ Size: 1.29 MB | Pages: 41 in PDF or view online for FREE

— 21 —

1)

Remove the screw (M1.4 

×

 1.4) 1.

2)

Remove the LS cam plate.

3)

Remove the tension coil spring (brake-S).

4)

Remove the brake-S.

5)

Remove the screw (M1.4 

×

 2) 2.

6)

Remove the torsion coil spring (brake arm).

7)

Remove the cassette position set-S from groove of the LS block
assy in the direction of the arrow A.

8)

Remove the brake-S drive arm assy from groove of the LS
block assy in the direction of the arrow B.

1)

Insert the brake-S drive arm assy under groove of the LS chassis
block assy.  Attach the brake-S drive arm assy to the brake-S
arm shaft and to the brake-S pivot shaft.

2)

Insert the cassette position set-S under the groove of the LS
chassis block assy.  Attach the cassette position set-S to the
brake-S arm shaft.

3)

Attach the torsion coil spring (brake arm).

4)

Attach the screw (M1.4 

×

 2) 2 to the brake-S arm shaft.

5)

Attach the brake-S to the brake-S arm bearing and to the brake-
S pivot shaft.

6)

Hook the tension coil spring (brake-S) to the spring stay of the
cassette position set-S and the spring stay of the brake-S.

7)

Align the slot of the LS cam plate with the dowel.  Move then
in the direction toward the arrow C and attach the screw (M1.4

×

 1.4) 1.

8)

Perform the LS cam plate position adjustment referring to
section 3-11.

2

×

×

1

×

1

×

A

B

B

C

C

— 22 —

1)

Remove the TG7 block assy in the direction of the arrow A.

2)

Remove the torsion coil spring (TG7 return) 1.

3)

Remove the pinch arm assy in the direction of the arrow B.

4)

Remove the torsion coil spring (pinch roller return) 2.

1)

Install the torsion coil spring (pinch roller return) 1.  (Insert
the 90-degree-bent portion of the torsion spring into the square
hole of the LS chassis block assy.)

2)

Attach the pinch arm assy to the pinch arm bearing.

3)

Attach the torsion coil spring (TG7 return) 1.

4)

While aligning the TG7 block assy with the groove of the LS
chassis block assy, install the TG7 block assy into the TG7
block assy bearing.

2

2

1

1

B

A

— 23 —

1)

Remove the sensor holder-T from groove of the LS chassis
block assy in the direction of the arrow A.

2)

Remove the cassette holder-S by pushing out the hook under
the LS chassis block assy towards the direction of the arrow
B

.

B

A

— 24 —

1)

Remove the TG1 cam slider.

2)

Remove the LS arm.  (At this moment, be careful that the LS
roller can come out of cam gear A groove.)

3)

Remove the LS roller from the LS arm.

4)

Remove the LS guide roller.

1)

Coat inside the LS guide roller with grease (1/4 drop of grease)
and insert it into the LS guide shafts S1 and S2.

2)

Coat outside the LS guide roller with grease (1/2 drop of grease)
at the two points as shown.

3)

While aligning dowel of the TG1 drive arm with groove of the
mode gear assy, insert the TG1 drive arm into the LS guide
shaft S1.

4)

Coat the portion A of the LS arm with grease (1/4 drop of
grease) and insert the LS guide roller.

5)

Coat both sides of the groove of the cam gear A with grease (1/
2 drop of grease).  Insert the LS guide roller into groove of the
cam gear A and insert the LS arm into the LS guide shaft S2.

6)

Insert the TG1 cam slider into the three positions of the LS
guide shaft S1, S2 and slider guide shaft.  Insert dowel of the
TG1 cam slider into groove of the cam gear A.

7)

Be careful that greasing points are correct, amount of grease is
correct and the LS arm and the TG1 drive arm are not floating.

LS R

J

M AA a

Œ Ø B

A