Sony GV-D300 Service Manual ▷ View online
5-21
10. S VIDEO Output Chroma Level Adjustment
(CB-61 Board)
(CB-61 Board)
Set the chroma signal level of the S video output signal.
Mode
VTR stop
Signal
No signal
Measurement Point
Chroma signal terminal of S VIDEO
jack (75
jack (75
Ω
terminated)
Measuring Instrument
Oscilloscope
Adjustment Page
D
Adjustment Address
94
Specified Value
A = 286 ± 6mV (NTSC)
A = 300 ± 6mV (PAL)
A = 300 ± 6mV (PAL)
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 15, after memorizing the data, set the
bit value of bit2 to “0”. (Refer to “4-3, 3. Bit value
discrimination” of “5-4. Service Mode”).
bit value of bit2 to “0”. (Refer to “4-3, 3. Bit value
discrimination” of “5-4. Service Mode”).
3)
Select page: D, address: 94, change the data and set the burst
signal level (A) to the specified value.
signal level (A) to the specified value.
4)
Press the PAUSE button of the adjustment remote commander.
5)
Select page: D, address: 15, and set the data memorized at step
2).
2).
6)
Press the PAUSE button of the adjustment remote commander.
7)
Select page: 0, address: 01, and set data: 00.
Fig. 5-3-15
11. AFC TC Adjustment (CB-61 Board)
Set the picture frame in recording.
Mode
VTR stop
Signal
75% color bar (VIDEO jack input)
Measurement Point
Y signal terminal of S VIDEO jack
(75
(75
Ω
terminated)
Measuring Instrument
Oscilloscope
Adjustment Page
D
Adjustment Address
A2
Specified Value
t
2
– t
1
= 0 ± 0.05
µ
sec
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 2, address: 13, and set data: FE.
3)
Check the delay time (t
1
).
4)
Select page: 2, address: 13, and set data: FF.
5)
Select page: D, address: A2, change the data so that the delay
time (t
time (t
2
) is equal to the delay time (t
1
) of step 3).
6)
Press the PAUSE button of the adjustment remote commander.
7)
Select page: 2, address: 13, and set data: 00.
8)
Select page: 0, address: 01, and set data: 00.
For NTSC model
For PAL model
Fig. 5-3-16
A
H
H
t
1
or t
2
H
t
1
or t
2
5-22
12. AFC f
0
Adjustment (CB-61 Board)
Set the free-run frequency of the AFC VCO.
Mode
VTR stop (GV-D900/D900E)
Recording (GV-D300/D300E)
Recording (GV-D300/D300E)
Signal
75% color bar (VIDEO jack input)
Measurement Point
Pin
@º of CN9928 (AFC ERR)
Measuring Instrument
Digital voltmeter
Adjustment Page
D
Adjustment Address
A1
Specified Value
A = 1.9 ± 0.1Vdc
Note:
Don’t insert any plug in the S VIDEO jack.
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: A1, change the data and set the AFC
error voltage (A) to the specified value.
error voltage (A) to the specified value.
3)
Press the PAUSE button of the adjustment remote commander.
4)
Select page: 0, address: 01, and set data: 00.
13. Decoder APC Adjustment (CB-61 Board)
Set the free-run frequency of the decoder VXO.
Mode
VTR stop (GV-D900/D900E)
Recording (GV-D300/D300E)
Recording (GV-D300/D300E)
Signal
No signal (VIDEO jack input) (Note)
Measurement Point
Pin
1 of CN9928 (DEC FSC)
Measuring Instrument
Frequency counter
Adjustment Page
D
Adjustment Address
9F
Specified Value
f = 3579545 ± 50Hz (NTSC)
f = 4433619 ± 50Hz (PAL)
f = 4433619 ± 50Hz (PAL)
Note:
Insert a plug in the VIDEO jack.
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 9F, change the data and set the DEC
FSC frequency (f) to the specified value.
FSC frequency (f) to the specified value.
3)
Press the PAUSE button of the adjustment remote commander.
4)
Select page: 0, address: 01, and set data: 00.
14. Decoder ACC Adjustment (CB-61 Board)
Set the decoder ACC gain.
Mode
VTR stop (GV-D900/D900E)
Recording (GV-D300/D300E)
Recording (GV-D300/D300E)
Signal
75% color bar (VIDEO jack input)
Measurement Point
Pin
!¶ of CN9928 (DEC B-Y)
Measuring Instrument
Oscilloscope
Adjustment Page
D
Adjustment Address
9E
Specified Value
A = 325 ± 20mV
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 9E, change the data and set the DEC
B-Y signal level (A) to the specified value.
B-Y signal level (A) to the specified value.
3)
Press the PAUSE button of the adjustment remote commander.
4)
Select page: 0, address: 01, and set data: 00.
Fig. 5-3-17
H
A
5-23
15. Decoder HUE Adjustment (CB-61 Board)
Set the decoder hue.
Mode
VTR stop (GV-D900/D900E)
Recording (GV-D300/D300E)
Recording (GV-D300/D300E)
Signal
75% color bar (VIDEO jack input)
Measurement Point
Pin
!¶ of CN9928 (DEC B-Y)
Measuring Instrument
Oscilloscope
Adjustment Page
D
Adjustment Address
A0
Specified Value
A-B = 0 ± 10mV (NTSC)
A = Minimum amplitude (PAL)
A = Minimum amplitude (PAL)
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
NTSC model
Select page: D, address: A0, change the data so that the voltage
(A) between the yellow and cyan is equal to the voltage (B)
between the green and magenta.
PAL model
Select page: D, address: A0, change the data so that the
waveform dose not appear double.
Select page: D, address: A0, change the data so that the voltage
(A) between the yellow and cyan is equal to the voltage (B)
between the green and magenta.
PAL model
Select page: D, address: A0, change the data so that the
waveform dose not appear double.
3)
Press the PAUSE button of the adjustment remote commander.
4)
Select page: 0, address: 01, and set data: 00.
For NTSC model
For PAL model
Fig. 5-3-18
H
B
A
A
H
16. Y AD Clamp Adjustment (CB-61 Board)
Set the IC9004 clamp level of the Y AD OUT.
Mode
VTR stop (GV-D900/D900E)
Recording (GV-D300/D300E)
Recording (GV-D300/D300E)
Signal
75% color bar (VIDEO jack input)
Measurement Point
DDS display of LCD or TV monitor
(Note1), or Page: 2, address: 1C
display data of the adjustment remote
commander
(Note1), or Page: 2, address: 1C
display data of the adjustment remote
commander
Measuring Instrument
Adjustment Page
D
Adjustment Address
B6
Specified Value
0F to 11
Note1:
The two digits of the display data of the LCD and TV monitor is
the object data.
the object data.
HI XX XXXX
Object data
Note2:
How to connect the TV monitor.
1) Use the LASER LINK function.
2) Connect the TV monitor to S VIDEO jack.
1) Use the LASER LINK function.
2) Connect the TV monitor to S VIDEO jack.
In this case, select page: 2, address: 13, and set data: FE. After
completing adjustments, set data: 00 to the address.
completing adjustments, set data: 00 to the address.
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 11, set data: 24, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
3)
Select page: 2, address: 96, and set data: 40.
4)
Select page: 2, address: 97, and set data: 18.
5)
Select page: D, address: B6, change the data and adjust the
DDS display data (or the display data of page: 2, address: 1C)
to the specified value. (The data of address: B6 should be “00”
to “99”.)
DDS display data (or the display data of page: 2, address: 1C)
to the specified value. (The data of address: B6 should be “00”
to “99”.)
6)
Press the PAUSE button of the adjustment remote commander.
Processing after Completing Adjustments
1)
1)
Select page: D, address: 11, set data: 00, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
2)
Select page: 0, address: 01, and set data: 00.
3)
Select page: 2, address: 96, and set data: 00.
4)
Select page: 2, address: 97, and set data: 00.
5-24
17. CR AD Clamp Adjustment (CB-61 Board)
Set the clamp level of the IC9004 CR AD OUT.
Mode
VTR stop (GV-D900/D900E)
Recording (GV-D300/D300E)
Recording (GV-D300/D300E)
Signal
75% color bar (VIDEO jack input)
Measurement Point
DDS display of LCD or TV monitor
(Note), or Page: 2, address: 1D
display data of the adjustment remote
commander
(Note), or Page: 2, address: 1D
display data of the adjustment remote
commander
Measuring Instrument
Adjustment Page
D
Adjustment Address
B4
Specified Value
FF or 00 or 01
Note:
Note: The two digits of the display data of the LCD and TV monitor
is the object data.
is the object data.
HI XX XXXX
Object data
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 11, set data: 24, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
3)
Select page: 2, address: 96, and set data: 40.
4)
Select page: 2, address: 97, and set data: 18.
5)
Select page: D, address: B4, set data: 4C, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
6)
Select page: D, address: B5, set data: 4C, and press the PAUSE
button.
button.
7)
Select page: D, address: B4, change the data and adjust the
DDS display data (or the display data of page: 2, address: 1D)
to the specified value. (The data of address: B4 should be “00”
to “99”.)
DDS display data (or the display data of page: 2, address: 1D)
to the specified value. (The data of address: B4 should be “00”
to “99”.)
8)
Press the PAUSE button of the adjustment remote commander.
9)
Perform “CB AD Clamp Adjustment”.
Processing after Completing Adjustments
1)
1)
Select page: D, address: 11, set data: 00, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
2)
Select page: 0, address: 01, and set data: 00.
3)
Select page: 2, address: 96, and set data: 00.
4)
Select page: 2, address: 97, and set data: 00.
18. CB AD Clamp Adjustment (CB-61 Board)
Set the clamp level of the IC9004 CB AD OUT.
Mode
VTR stop (GV-D900/D900E)
Recording (GV-D300/D300E)
Recording (GV-D300/D300E)
Signal
75% color bar (VIDEO jack input)
Measurement Point
DDS display of LCD or TV monitor
(Note1), or Page: 2, address: 1E
display data of the adjustment remote
commander
(Note1), or Page: 2, address: 1E
display data of the adjustment remote
commander
Measuring Instrument
Adjustment Page
D
Adjustment Address
B5
Specified Value
FF or 00 or 01
Note1:
Note: The two digits of the display data of the LCD and TV monitor
is the object data.
is the object data.
HI XX XXXX
Object data
Note2:
Perform “CR AD Clamp Adjustment” before this adjustment.
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: D, address: 11, set data: 24, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
3)
Select page: 2, address: 96, and set data: 40.
4)
Select page: 2, address: 97, and set data: 18.
5)
Select page: D, address: B5, change the data and adjust the
DDS display data (or the display data of page: 2, address: 1E)
to the specified value. (The data of address: B5 should be “00”
to “99”.)
DDS display data (or the display data of page: 2, address: 1E)
to the specified value. (The data of address: B5 should be “00”
to “99”.)
6)
Press the PAUSE button of the adjustment remote commander.
Processing after Completing Adjustments
1)
1)
Select page: D, address: 11, set data: 00, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
2)
Select page: 0, address: 01, and set data: 00.
3)
Select page: 2, address: 96, and set data: 00.
4)
Select page: 2, address: 97, and set data: 00.
Click on the first or last page to see other GV-D300 service manuals if exist.