DOWNLOAD Sony GV-D300 Service Manual ↓ Size: 27.72 MB | Pages: 127 in PDF or view online for FREE

5-17

In some adjustments, the color bar signal generated by DCR-
VX1000(NTSC) or DCR-VX1000E(PAL) is used for the video input
signal.

1)

Connect the adjustment remote commander to DCR-
VX1000(NTSC) or DCR-VX1000E(PAL).

2)

Set the power switch to CAMERA.

3)

Select page: 5, address: 02, and set data: 09.
By carrying out the above procedure, DCR-VX1000(NTSC)
or DCR-VX1000E(PAL) generates the color bar signal. After
completing adjustments, set data: 00 to the address.

Set the NPS PLL free-run frequency.

Mode

VTR stop

Signal

Color bar signal generated by DCR-
VX1000(NTSC) or DCR-
VX1000E(PAL) (DV jack input)

Measurement Point

Pin 

!¶ of CN9932 (NPS PLL)

Measuring Instrument

Frequency counter

Adjustment Element

CT1200

Specified Value

f = 14318180 ± 100Hz (NTSC)
f = 17734480 ± 100Hz  (PAL)

Adjusting method:
1)

Set the frequency (f) to the specified value using CT1200.

Set the IC1103 PB Y input signal level.

Mode

VTR stop

Signal

Color bar signal generated by DCR-
VX1000(NTSC) or DCR-
VX1000E(PAL) (DV jack input)

Measurement Point

Pin 

!• of CN9932 (NPS Y)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

59

Specified Value

A = 125 ± 3mV (NTSC)
A = 140 ± 3mV (PAL)

Connection: Connect Pin 

!• of CN9932 and Pin !ª (GND) of

CN9932 with a 470 

Ω

 resistor (Parts code: 1-249-413-11)

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 59, change the data and set the sync
signal level (A) to the specified value.

3)

Press the PAUSE button of the adjustment remote commander.

4)

Select page: 0, address: 01, and set data: 00.

5)

Perform “Video Output Y Level Adjustment”.

Fig. 5-3-8

H

A

5-18

Set the Y signal level of the Video output signal.

Mode

VTR stop

Signal

No signal

Measurement Point

VIDEO jack (75 

Ω 

terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

96

Specified Value

A = 286 ± 6mV (NTSC)
A = 300 ± 6mV (PAL)

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 15, after memorizing the data, set the
bit value of bit2 to “0”. (Refer to “4-3, 3. Bit value
discrimination” of “5-4. Service Mode”).

3)

Select page: D, address: 96, change the data and set the sync
signal level (A) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: D, address: 15, and set the data memorized at
step 2).

6)

Press the PAUSE button of the adjustment remote commander.

7)

Select page: 0, address: 01, and set data: 00.

8)

Perform “VIDEO Output Chroma Level Adjustment”.

Fig. 5-3-9

Set the Y signal level of the S video output signal.

Mode

VTR stop

Signal

No signal

Measurement Point

Y signal terminal of S VIDEO jack
(75 

Ω 

terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

95

Specified Value

A = 286 ± 6mV (NTSC)
A = 300 ± 6mV (PAL)

 Insert a plug in the S VIDEO jack.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 15, after memorizing the data, set the
bit value of bit2 to “0”. (Refer to “4-3, 3. Bit value
discrimination” of “5-4. Service Mode”).

3)

Select page: D, address: 95, change the data and set the sync
signal level (A) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: D, address: 15, and set the data memorized at
step 2).

6)

Press the PAUSE button of the adjustment remote commander.

7)

Select page: 0, address: 01, and set data: 00.

Fig. 5-3-10

A

H

A

H

5-19

Set the IC9004 AGC gain.

Mode

VTR stop

Signal

Color bar (VIDEO jack input)

Measurement Point

Y signal terminal of S VIDEO jack
(75 

Ω 

terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

9A

Specified Value

A = 1.00 ± 0.02V

Before perform this adjustment, check that the specified value of “S
VIDEO Output Level Adjustment” is satisfied.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 13, and set data: FE.

3)

Select page: D, address: 9A, change the data and set the Y
signal level (A) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 2, address: 13, and set data: 00.

6)

Select page: 0, address: 01, and set data: 00.

Fig. 5-3-11

H

A

White (100%)

A

White (100%)

H

Set the IC1101 CB OUT level.

Mode

VTR stop

Signal

Color bar signal generated by DCR-
VX1000(NTSC) or DCR-
VX1000E(PAL) (DV jack input)
(Note)

Measurement Point

VIDEO jack (75 

Ω

 terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

99

Specified Value

A = 450 ± 10mV (NTSC)
A = 460 ± 10mV (PAL)

How to generate the color bar signal.
1) Connect the adjustment remote commander to DCR-

VX1000(NTSC) or DCR-VX1000E(PAL).

2) Set the power switch to CAMERA.
3) Select page: 5, address: 02, and set data: 09.

By carrying out the above procedure, DCR-VX1000(NTSC) or
DCR-VX1000E(PAL) generates the color bar signal. After
completing adjustments, set data: 00 to the address.

Adjusting method:
1)

Check that RV1200 is the mechanical center.

2)

Select page: 0, address: 01, and set data: 01.

3)

Select page: D, address: 99, change the data and set the blue
level (A) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 0, address: 01, and set data: 00.

6)

Perform “VIDEO Output Burst Level Adjustment”.

Fig. 5-3-12

A

H

Blue

5-20

Set the composite output burst signal level.

Mode

VTR stop

Signal

Color bar signal generated by DCR-
VX1000(NTSC) or DCR-
VX1000E(PAL) (DV jack input)

Measurement Point

VIDEO jack (75 

Ω 

terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

A6

Specified Value

A = 286 ± 6mV (NTSC)
A = 300 ± 6mV (PAL)

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: A6, change the data and set the burst
level (A) to the specified value.

3)

Press the PAUSE button of the adjustment remote commander.

4)

Select page: 0, address: 01, and set data: 00.

Fig. 5-3-14

A

H

Adjust the IC1101 CR OUT level, and set the chroma phase.

Mode

VTR stop

Signal

Color bar signal generated by DCR-
VX1000(NTSC) (DV jack input)

Measurement Point

VIDEO jack

Measuring Instrument

Vectorscope

Adjustment Page

D

Adjustment Address

97

Specified Value

All color luminance points should
settle within each specified frame( ).

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Adjust the GAIN and PHASE of the vectorscope, and set the
burst luminance point to the burst position (75% position).

3)

Select page: D, address: 97, change the data and settle each
color luminance point in each specified frame ( ).

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 0, address: 01, and set data: 00.

Adjust the IC1101 CR out level.

Mode

VTR stop

Signal

Color bar signal generated by DCR-
VX1000E(PAL) (DV jack input)

Measurement Point

VIDEO jack (75 

Ω 

terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

97

Specified Value

A = 640 ± 10mV

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 97, change the data and set the red
level (A) to the specified value.

3)

Press the PAUSE button of the adjustment remote commander.

4)

Select page: 0, address: 01, and set data: 00.

Fig. 5-3-13

Red

A

H