DOWNLOAD Sony GV-D300 Service Manual ↓ Size: 27.72 MB | Pages: 127 in PDF or view online for FREE

5-1

• Oscilloscope

• Regulated power supply

• Vectorscope

• Frequency counter

• Adjustment screwdriver

• Monitor TV

• Digital voltmeter

• Pattern signal generator

J-1

J-2

J-6

J-3

J-7

J-8

J-4

J-5

Fig. 5-1-1.

J-9

Refer to section “5-4. SERVICE MODE” for the adjustment
remote commander.

If the microprocessor IC in the adjustment remote commander is not the new microprocessor (UPD7503G-C56-12), the pages cannot be switched.
In this case, replace the IC with the new microprocessor (8-759-148-35).

J-1

J-2

J-3

J-4

J-5

J-6

J-7

J-8

J-9

Adjustment remote commander (RM-95 upgraded). Note

CPC-6 jig

CPC-6 terminal board jig

Power cable

IR receiver jig

Extension cable (80P, 0.5mm)

Extension cable (50P, 0.5mm 

→

 48P, 0.8mm)

Extension cable (18P, 0.5 mm)

CPC-10 jig

J-6082-053-B

J-6082-370-A

J-6082-371-A

J-6082-223-A

J-6082-383-A

J-6082-421-A

J-6082-422-A

J-6082-423-A

J-6082-424-A

For adjusting the video section

For adjusting the video section

For correction between the battery terminal and DC power
supply unit

For adjusting the IR transmitter

For extension between the CB-61 board (CN9921) and
the RJ-77 board (CN9901)

For extension between the CB-61 board (CN9930) and
the RJ-77 board (CN9904)

For extension between the RJ-77 board (CN3100) and
capstan motor

For adjusting the LCD system

5-2

For details of mechanism section adjustments, checks, and
replacement of mechanism parts, refer to the separate volume “DV
MECHANICAL ADJUSTMENT MANUAL      D Mechanism
and  DV  MECHANICAL  ADJUSTMENT  MANUAL  
 D200 Mechanism ”.

1)

Refer to “2. Removal” and supply the power with the cabinet
assembly removed.

2)

Connect the adjustment remote commander to the LANC jack.

3)

Turn on the HOLD switch of the adjustment remote
commander.

4)

Close the cassette compartment without the cassette.

5)

Select page: 0, address: 01, and set data: 01.

6)

Select page: C, address: 52, and set data: FD, and press the
PAUSE button of the adjustment remote commander.

7)

Select page: D, address: 10, and set data: 10, and press the
PAUSE button of the adjustment remote commander.

8)

Turn off the HOLD switch of the adjustment remote
commander.

9)

Turn the power off and then on.

The above procedure enables the mechanism to operate without the
cassette. After checking operations be sure to perform “Procedure
After Checking Operations”.
To use the “No-Cassette Operation Mode” and “Forced Power ON
Mode” together, set the following data to page: D, address:10.

Forced power ON mode ...................................................... 12

1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: C, address: 52, and set data: FF, and press the
PAUSE button of the adjustment remote commander.

3)

Select page: D, address: 10, and set data: 00, and press the
PAUSE button.

4)

Select page: 0, address: 01, and set data: 00.

5)

Disconnect the power supply of the unit.

1)

Clean the tape running side (tape guide, drum, capstan shaft,
pinch roller).

2)

Connect the adjustment remote commander to the LANC jack.

3)

Turn on the HOLD switch of the adjustment remote
commander.

4)

Select page: 3, address: 3C, and set data: 07 (NTSC), 27 (PAL).

5)

Connect the oscilloscope.
Channel 1: CB-61 board, CN9928 Pin !¢ (RF MONITOR)

(Note 1)

External trigger: CB-61 board, CN9928 Pin !§

Connect the oscilloscope via CPC-6 jig (J-6082-370-A),
CPC- 6 terminal board jig (J-6082-371-A).

Connect Pins !¢ and !£ (GND) of CN9928 with a 75 

Ω

 resistor.

6)

Playback an alignment tape (XH2-1) for tracking.

7)

Check that the oscilloscope RF waveform is flat at the entrance
and exit. If not flat, adjust according to the separate volume
“DV MECHANICAL ADJUSTMENT MANUAL 
D Mechanism and DV MECHANICAL ADJUSTMENT
MANUAL     D200 Mechanism  ”.

8)

After completing the adjustment, perform “2. Procedure after
checking operations”.

1)

Connect the adjustment remote commander, and turn on the
HOLD switch.

2)

Select page: 3, address: 3C, and set data: 00.

3)

Disconnect the power supply of the unit.

Fig. 5-2-1

1

3

5

7

9

11

13

15

17

19

DEC FSC

GND

ENV OUT

LOCK

VCC1

VCC2

GND

GND

DEC B-Y

CPC VGL –18V

2

4

6

8

10

12

14

16

18

20

GND

XCHG

GND

RF OUT

EQ IN

AGC IN

RF MONITOR

JSWP

DEC R-Y

AFC ERR

CH1

CH2
(Trigger)

Must be flat

3.3msec

5-3

Use the following measuring instruments for video section
adjustments.

1)

TV monitor

2)

Oscilloscope (dual-phenomenon, band above 30 MHz with
delay mode) (Unless specified otherwise, use a 10 : 1 probe.)

3)

Frequency counter

4)

Pattern generator with video output terminal

5)

Digital video camera recorder
DCR-VX1000 (NTSC)
DCR-VX1000E (PAL)

6)

Vectorscope

7)

Digital voltmeter

8)

Audio generator

9)

Audio level meter

10) Audio distortion meter
11) Audio attenuator
12) Regulated power supply
13) Alignment tapes

• Tracking standard (XH2-1)

Parts code: 8-967-997-01

• SW/OL standard (XH2-3)

Parts code: 8-967-997-11

• Audio operation check for NTSC (XH5-3)

Parts code: 8-967-997-51

• System operation check for NTSC (XH5-5)

Parts code: 8-967-997-61

• BIST check for NTSC (XH5-6)

Parts code: 8-967-997-71

• Audio operation check for PAL (XH5-3P)

Parts code: 8-967-997-55

• System operation check for PAL (XH5-5P)

Parts code: 8-967-997-66

• BIST check for PAL (XH5-6P)

Parts code: 8-967-997-76

14) Adjustment remote commander (J-6082-053-B)
15) IR receiver jig (J-6082-383-A)
16) CPC-6 jig (J-6082-370-A)
17) CPC-6 terminal board jig (J-6082-371-A)
18) Extension cable (50P, 0.5 mm — 48P, 0.8mm)

For extension between the CB-61 board (CN9930) and the RJ-
77 board (CN9904) (J-6082-422-A)

19) Extension cable (80P, 0.5 mm)

For extension between the CB-61 board (CN9921) and the RJ-
77 board (CN9901) (J-6082-421-A)

20) Extension cable (18P, 0.5 mm)

For extension between the RJ-77 board (CN3100) and the
capstan motor. (J-6082-423-A)

21) CPC-10 jig (J-6082-424-A)

For details of the adjustment remote commander, refer to
“5-4. SERVICE MODE”.

5-4

1)

Removing the CB-61 board CN9926 means removing the
lithium 3V power supply (FP-571 board BT001) , data such as
date, time, user-set menus will be lost. After completing
adjustments, reset these data. If the CB-61 board CN9926 has
been removed, the self-diagnosis data, data on history of use
(total drum rotation time etc. ) will be lost. Before removing,
note down the self-diagnosis data and the data on the history
use (data of page: 2, address: 35 to 3D). (Refer to the “5-4.
Service Mode” for the data on the history use.)

2)

The LCD block and EASY connector need not be connected
except during “Battery End Adjustment” and “LCD system
Adjustments”. To remove, disconnect the following connectors.

1. CB-61 board CN9923 (32P, 0.5mm)
2. CB-61 board CN9931 (40P, 0.5mm)

3)

IR-29 board (PANEL CLOSE switch, LASER LINK
transmitter) need not be connected except during “IR
Transmitter Adjustment”. To remove, disconnect the following
connectors.

1. CB-61 board CN9924 (10P, 0.5mm)

4)

If opening the CB-61 board, use the following extension cable
between the CB-61 board CN9921/CN9930 and RJ-77 board
CN9901/CN9904.

1. J-6082-421-A (80P, 0.5mm)
2. J-6082-422-A (50P, 0.5mm — 48P, 0.8mm)

5)

If opening the RJ-77 board, use the following extension cable
between the RJ-77 board (CN3100) and capstan motor.

1. J-6082-423-A (18P, 0.5mm)

1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE

button of the adjustment remote commander.

The above procedure will enable the VTR power to be turned on
with the power switch block (FP-575) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.

1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE

button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

Some of the adjusting points (except for that of the LCD system
adjustments) are concentrated at CB-61 board CN9928 and CN9932.
Connect the measuring instruments via the CPC-6 jig (J-6082-370-
A) , CPC-6 terminal board jig (J-6082-371-A). The following tables
list the pin numbers and signal names of CN9928 and CN9932.

1

3

5

7

9

11

13

15

17

19

DEC FSC

GND

ENV OUT

LOCK

VCC1

VCC2

GND

GND

DEC B-Y

CPC VGL –18V

2

4

6

8

10

12

14

16

18

20

GND

XCHG

GND

RF OUT

EQ IN

AGC IN

RF MONITOR

JSWP

DEC R-Y

AFC ERR

1

3

5

7

9

11

13

15

17

19

GND

TDI

TCK

GND

GND

GND

NPS B-Y

GND

NPS PLL

GND

2

4

6

8

10

12

14

16

18

20

GND

TDAA

TMS

GND

NPS C

GND

NPS R-Y

GND

NPS Y

GND