Sony KV-HG29M80 Service Manual ▷ View online
– 8 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
2-5. Dress Conn Assy, 5P Video2 and Conn Assy, 6P Karaoke using pin, wire A013 (For HG PiP models)
2-4. Wire Dressing at A, K and H2 board (HG29 PiP models)
3) Insert Conn Assy, 5P Video2 into CN4105.
4) Insert and dress Conn Assy, 6P Karaoke (Red) into holder.
5) Insert Conn Assy, 3P SCL (Red) into CN8209.
4) Insert and dress Conn Assy, 6P Karaoke (Red) into holder.
5) Insert Conn Assy, 3P SCL (Red) into CN8209.
1) Insert and dress Conn Assy, 4P into hook.
2) Next, dress Conn Assy, 6P MicSW into the 2 holders.
2) Next, dress Conn Assy, 6P MicSW into the 2 holders.
Conn Assy, 4P
Conn Assy, 7P
CN4113
CN3102
CN4110
CN2105
CN4106
CN8108
Conn Assy, 6P
MicSW
1
2
2
AC Power Cord is
behind Lead Assy,
Speaker
behind Lead Assy,
Speaker
TVSR:
Connector assy must be kept away from primary area
(10mm minimum).
Connector assy must be kept away from primary area
(10mm minimum).
CN4105
CN8208
3
Conn Assy,
6P
Conn Assy, 5P
Video 2
4
CN8209
5
CN606
Lead Assy, Speaker
Conn Assy, 3P
SCL (Red)
Dress Conn Assy, 3P SCL (Red) using pin, wire A8101
as shown.
as shown.
Note: Dress while chassis is halfway docked into beznet.
Pin, wire A013
Keep wires away from heatsinks
Conn Assy, 6P AFT and Conn Assy, 6P
Karaoke (Red) are dressed using pin, wire A013.
Karaoke (Red) are dressed using pin, wire A013.
Conn Assy, 6P AFT
Conn Assy, 6P Karaoke (Red)
Pin, Wire A013
Pin, wire A8101
Conn Assy, 3P SCL (Red)
Conn Assy, 6P Karaoke (Red)
Conn Assy, 6P AFT
– 9 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
2-6. Dressing of Conn Assy, 4P VH
(all HG29 models)
2-7. Dressing of Conn Assy, 5P YUV
(HG
(HG
Non-PiP)
2-8. Dressing of Conn Assy, 4P VM and
Connector Assy, 5P Video2 (HG Non-PiP)
2-9. Dressing of Conn Assy, 5P YUV
(HG PiP models)
Dress Conn Assy, 4P VH into holder as shown.
Dress Conn Assy, 5P YUV around shield case.
Use pin, wires A019 and A017 to dress Conn Assy,
5P YUV as shown.
Use pin, wires A019 and A017 to dress Conn Assy,
5P YUV as shown.
Dress Conn Assy, 4P VM behind Conn Assy, 5P Video2 as shown.
Conn Assy, 5P Video2 is used to prevent Conn Assy, 4P VM from
bending towards T504, R579 and R5032 (high temperature parts).
Conn Assy, 5P Video2 is used to prevent Conn Assy, 4P VM from
bending towards T504, R579 and R5032 (high temperature parts).
CAUTION:
Keep Conn Assy, 5P Video2 away from deflection area
(T504, R5032, etc.) when dressing.
Keep Conn Assy, 5P Video2 away from deflection area
(T504, R5032, etc.) when dressing.
CN6101
CN4102
Pull wires to the left while
inserting it into hook. Keep it
away from touching T603.
T603
CN007
CN905
Pin, wire A019
Pin, wire A017
Dress Conn Assy, 5P YUV
around shield case
Make sure the UL tape is positioned at
the sharp edge of shield case to prevent
wire from being scratched
the sharp edge of shield case to prevent
wire from being scratched
CN9201
Conn Assy, 5P YUV
Insert Connector Assy,
4P VH into holder
Keep wires away
from R121
Dress Conn Assy, 5P YUV to the right as shown.
R5032
T504
CN003
Conn Assy, 5P
Video2
R579
Lead Assy, Earth is
above Conn Assy, 5P Video2
Deflection area
CN9201
Dress Conn Assy, 5P YUV to the right
CN007
Dress Conn Assy, 4P VM behind
Conn Assy, 5P Video2
Conn Assy, 4P VM
– 10 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
2-10. Dressing of Conn Assy, 4P VM and
Connector Assy, 5P Video2 (HG PiP models)
2-11. Installation and dressing of Earth Assy,
Coating
Coating
2-12. Installation and dressing of Earth Assy,
Coating
Coating
2-13. Insertion of Lead Assy, H Static
Earth Assy, Coating is installed as shown
Dress Conn Assy, 4P VM behind Conn Assy, 5P Video2 as shown.
Conn Assy, 5P Video2 is used to prevent Conn Assy, 4P VM from
bending towards T504, R579 and R5032 (high temperature parts).
Conn Assy, 5P Video2 is used to prevent Conn Assy, 4P VM from
bending towards T504, R579 and R5032 (high temperature parts).
R5032
T504
CN003
CN9201
Conn Assy, 5P Video2
Conn Assy, 4P
R579
Dress Conn Assy, 4P VM behind
Conn Assy, 5P Video2
R121
Right side
Left side
i) Insert the 2 Earth Assy, Coating wires to CN705 & CN707 as shown.
ii) Insert Conn Assy, 7P RGB into CN701.
ii) Insert Conn Assy, 7P RGB into CN701.
Insert Lead Assy, H Static into CRT socket and RV750 as shown.
Make sure the wire is naturally curved, to avoid touching CRT neck.
Make sure the wire is naturally curved, to avoid touching CRT neck.
CV
CN701
Heatsink A751
Conn Assy, 7P RGB
BLK+BLK
to CN707
to CN707
BLK+BLK
to CN705
to CN705
Earth Assy, Coating
CV board
CN707
CN705
Lead Assy, H Static
RV750
CRT socket
CRT neck
CN707
Earth Assy,Coating
wires
wires
CN705
CAUTION:
Keep Conn Assy, 5P Video 2 and Conn Assy, 4P VM wire away
from deflection area (T504, R5032, etc.) when dressing.
Keep Conn Assy, 5P Video 2 and Conn Assy, 4P VM wire away
from deflection area (T504, R5032, etc.) when dressing.
– 11 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
2-14. CV board Connector Assy wire dressing
2-15. Dressing of Conn Assy, 5P Video2
2-16. Dress Lead Assy, Earth and Conn Assy, 5P
VIdeo2 with purse lock Ø 5
2-17. P board Installation (HG PiP models)
i) Dress Conn Assy, 6P and Conn Assy, 4P VM using tie, cable at
alignment hole 'B' on CV board as shown.
ii) Dress Conn Assy, 4P 200V; Conn Assy, 6P; Conn Assy, 4P VM; Lead
Assy, G2 and Lead Assy, Focus with purse lock Ø 5
alignment hole 'B' on CV board as shown.
ii) Dress Conn Assy, 4P 200V; Conn Assy, 6P; Conn Assy, 4P VM; Lead
Assy, G2 and Lead Assy, Focus with purse lock Ø 5
Make a 'S' shaped loop on Conn Assy, 5P Video2 as shown.
Keep wires away from heatsink A010.
Keep wires away from heatsink A010.
Conn Assy, 6P
Pin, wire A707
Lead Assy,
Focus
Purse lock Ø 5
Tie, cable at alignment hole 'B'
Conn Assy, 4P 200V
Conn Assy, 4P VM
Lead Assy,Focus
Conn Assy, 6P
Conn Assy, 4P 200V
Conn Assy, 4P VM
Lead Assy, G2
Purse lock Ø 5
Heatsink A010
Lead Assy, Earth
Lead Assy, Speaker
Lead Assy, G2
Conn Assy, 5P
Video2
1) Once chassis has been docked into bottom cover, proceed
to install P board into bottom cover.
to install P board into bottom cover.
2) Insert P-P cable into tuner.
3) Insert Conn Assy, 6P Karaoke (White) from A board to CN1402 on P board.
4) Insert Conn Assy, 5P YUV from CN1404 on P board to to CN905 on A board.
Dress Conn Assy, 6P Karaoke (White) and Conn Assy, 5P YUV behind P-P cable.
5) Insert Conn Assy, 3P SCL (White) from A board to CN1409 on P board.
4) Insert Conn Assy, 5P YUV from CN1404 on P board to to CN905 on A board.
Dress Conn Assy, 6P Karaoke (White) and Conn Assy, 5P YUV behind P-P cable.
5) Insert Conn Assy, 3P SCL (White) from A board to CN1409 on P board.
Note: Dress wires while chassis is halfway docked into beznet.
*Only HG29 PiP models use Conn Assy, 6P Karaoke (Red)
and Conn Assy, 6P AFT.
Conn Assy, 5P Video2
Heatsink A010
Conn Assy, 6P AFT*
Conn Assy, 6P Karaoke (Red)*
Make a 'S' shaped loop on Conn
Assy, 5P Video2 and dress
together with Lead Assy,Earth
using purse lock Ø 5.
Assy, 5P Video2 and dress
together with Lead Assy,Earth
using purse lock Ø 5.
Conn Assy, 5P Video2
Lead Assy, Earth
Purse lock Ø
Chassis docked into bottom cover
1
Lead Assy, Speaker is not dressed together with purse lock.
Keep Lead Assy, Speaker away from heatsink A010 by
dressing it close to the CRT.
Keep Lead Assy, Speaker away from heatsink A010 by
dressing it close to the CRT.
Lead Assy,
Earth
2
P-P cable
3
P-P cable
Conn Assy, 6P
Karaoke (White)
CN1402
CN905
CN010
CN1404
5
CN1409
4
Conn Assy, 5P YUV
Conn Assy, 3P SCL (White)
Click on the first or last page to see other KV-HG29M80 service manuals if exist.