Sony KV-HG29M80 Service Manual ▷ View online
– 4 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
[+B overcurrent $OCP%]
Occurs when an overcurrent on the +B(135V) line is detected by pin 32 of IC001 (A board).
If the voltage of pin 32 of IC001 (A board) is more than 4V, the unit will automatically go to
standby.
If the voltage of pin 32 of IC001 (A board) is more than 4V, the unit will automatically go to
standby.
[V-PROTECT]
Occurs when an absence of the vertical deflection pulse is detected by pin 13 of IC001
(A board).
(A board).
[IK $AKB%]
If the RGB levels* do not balance within 15 sec after the power is turned on, this error will be
detected by IC001 (A board). TV will stay on, but there will be 5 times LED blinking.
detected by IC001 (A board). TV will stay on, but there will be 5 times LED blinking.
Occurs when IC001 internal HV protect detects an abnormal H-Pulse (frequency) due to
improper power supply to IC001. TV cuts off high voltage power of anode CRT. No picture will be
detected. eg: IC602, IC604 go faulty.
improper power supply to IC001. TV cuts off high voltage power of anode CRT. No picture will be
detected. eg: IC602, IC604 go faulty.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
A BOARD
IC001
Y/CHROMA JUNGLE
A BOARD
IC503
V.OUT
A BOARD
IC001
SYSTEM
A BOARD
IC003
MEMORY
FROM
CV BOARD
IC751 PIN 5
IK
EHT0
RED LED
DISPLAY
SDA1
V.GUARD
SDA
5
F.B-PLS
3
13
84
32
122
A BOARD
FROM
Q816
COLLECTOR
99
POWER SUPPLY NG (+5V)
for VIDEO PROCESSOR
for VIDEO PROCESSOR
4. SELF DIAGNOSTIC SCREEN DISPLAY
5. HANDLING SELF DIAGNOSTIC SCREEN DISPLAY
6. SELF-DIAGNOSTIC CIRCUIT
2 :
000
3 :
N/A
4 :
000
5 :
001
8 :
002
101 :
N/A
"0" means no fault has been detected.
"1" means a fault has been detected.
"2" means two faults has been detected.
"2" means two faults has been detected.
"N/A" means not available for this models.
SELF DIAGNOSTIC
5
8
No.
Description
Method
1.
Display self diagnostic screen
[Display] t [Channel ] t [Volume ] t [Power / TV]
Note: The above must be performed while TV is on standby mode.
2.
Stop standby flash
i) Turn off power switch on main.
ii) Unplug power cord from the outlet.
ii) Unplug power cord from the outlet.
3.
Clear fault result
In self diagnostic screen, press
[Channel ] t
-
Note: Diagnostic results display on screen is not automatically cleared. Therefore,
clear result after completion of repair.
clear result after completion of repair.
4.
Quit self diagnostic screen
Turn off power switch of remote commander or main unit.
– 5 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
SECTION 1
DISASSEMBLY
1-2.
SPEAKER REMOVAL
1-3.
CHASSIS ASSY REMOVAL
1-4.
SERVICE POSITION
1-5.
K BOARD AND P BOARDS REMOVAL
(KV-HG29M64K/L,M86K/L)
1-1.
REAR COVER REMOVAL
1
Eleven screws
(+BVTP 4
×
16 TYPE2 IT-3)
2
Rear cover
2
Two screws
TAPPING
SCREW
(+PWH
4
×
16)
1
Two screws
(+BVTP
3
×
12
TYPE2 IT-3)
P Board
K Board
A Board
H2 Board
1-6.
A AND H2 BOARDS REMOVAL
– 6 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
1-7.
PICTURE TUBE REMOVAL
Note:
•
Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom
right and left.
right and left.
1) Remove the rear cover.
2) Unplug all interconnecting leads from the Deflection yoke, Neck assy, Degaussing Coil and CRT grounding strap.
2) Unplug all interconnecting leads from the Deflection yoke, Neck assy, Degaussing Coil and CRT grounding strap.
Remove Chassis Assy.
3) Place the TV set with the CRT face down on a cushion jig.
• REMOVAL OF ANODE-CAP
Note:
• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or
carbon paint on the CRT.
•
REMOVING PROCEDURES
1
Turn up one side of the rubber cap in the direction
indicated by the arrow
indicated by the arrow
a
.
2
Using a thumb pull up the rubber cap firmly in the direction
indicated by the arrow
indicated by the arrow
b
.
3
When one side of the rubber cap is separated from the
anode button, the anode-cap can be removed by turning
up the rubber cap and pulling it up in the direction of the
arrow
anode button, the anode-cap can be removed by turning
up the rubber cap and pulling it up in the direction of the
arrow
c
.
•
HOW TO HANDLE AN ANODE-CAP
1
Do not damage the surface of anode-caps with sharp
shaped objects.
shaped objects.
2
Do not press the rubber too hard so as not to damage
the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built
into the rubber.
the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built
into the rubber.
3
Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the
rubber.
The shatter-hook terminal will stick out or damage the
rubber.
a
a
b
b
c
Anode Button
4
Anode Cap Removal
9
Degaussing Coil
6
Loosen the Neck Assembly
fixing screw and remove
VM
coil
7
Loosen the Deflection Yoke
fixing screw and remove
5
CV Board Removal
0
Earth Coating Assy
8
Band, DGC Removal (x1)
qa
Spring Extension
Removal
(x2)
qd
Screw Tapping 7+ Crown Washer (x4)
qs
Supports, CRT
Removal
(x2)
– 7 –
KV-HG29M50,M60/L,M64K/L,M80,M86K/L,N60
RM-GA002
CAUTION:
1. Do not overpull the wire during dressing
_> avoid disconnection of wires.
2. Make sure wires are kept away from
sharp edges, heatsinks & other
hight-temperature parts.
1. Do not overpull the wire during dressing
_> avoid disconnection of wires.
2. Make sure wires are kept away from
sharp edges, heatsinks & other
hight-temperature parts.
Legend:
Hook
SECTION 2
WIRE DRESSING
2-1. Lead Assy, Jumper wire dressing at A board
(for non-PiP models)
2-2. Lead Assy, Jumper wire dressing at A board
(for HG PiP models)
2-3. Wire Dressing at A and H2 board (HG29 non-PiP models)
1) Insert and dress Conn Assy, 4P into hook.
2) Insert Conn Assy, 5P into CN4105.
Insert Conn Assy, 5P into hook.
Make sure AC Power Cord is behind Lead
Assy, Speaker at CN4106.
Insert Conn Assy, 5P into hook.
Make sure AC Power Cord is behind Lead
Assy, Speaker at CN4106.
W054
W077
W010
W083
C903
Dress wires far away from C514 and T501.
CN010
W065
Lead Assy, Earth
T501
C514
CN905
Keep wires close to
shield case and
away from R121.
Also keep it to the
right of CN9201.
shield case and
away from R121.
Also keep it to the
right of CN9201.
R121
Press wires down
towards board
towards board
W081
W082
Lead Assy, Jumper
CN9201
W082
W077
W010
W084
W065
For HG-non PiP
Dress Lead Assy, Jumper
P/N 1-910-026-28 &
1-923-512-11 around CN905,
C903 and below Conn Assy,
5P YUV.
P/N 1-910-026-28 &
1-923-512-11 around CN905,
C903 and below Conn Assy,
5P YUV.
CN905
P/N 1-923-512-11
C514
Dress both Lead Assy, Jumpers
along edge of shield case
along edge of shield case
Dress Lead Assy,
Jumper far away from
C514 and T501.
Jumper far away from
C514 and T501.
T501
Conn Assy, 4P
Conn Assy, 7P
Insert Conn Assy,
4P into hook
4P into hook
CN4113
CN3102
CN4110
CN2105
1
TVSR:
Connector assy must be kept away from
primary area (10mm minimum).
Connector assy must be kept away from
primary area (10mm minimum).
CN4105
CN4106
Lead Assy, Speaker
2
W016
P/N 1-910-026-28
Keep Lead Assy, Jumper
away from R121
away from R121
C903
P/N 1-923-512-11
W016
Dress wire W081-W082
around CN905, C903.
around CN905, C903.
AC Power Cord is behind
Lead Assy, Speaker
Lead Assy, Speaker
Conn Assy, 5P
Conn Assy, 5P YUV
Click on the first or last page to see other KV-HG29M80 service manuals if exist.