DOWNLOAD Sony KV-HG21M85 Service Manual ↓ Size: 11.17 MB | Pages: 69 in PDF or view online for FREE

– 16 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:

Picture control ......................................................... NORMAL
Brightness control ................................................... NORMAL

Perform the adjustments in order as follows:
1. Beam Landing
2. Convergence
3. Focus
4. G2 (SCREEN)
5. White Balance

Note: Test Equipment Required
1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.

• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's

picture tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loosen the deflection yoke mounting screw, and set the

purity control to the center as shown below.

3. Set the raster signal of the pattern generator to green.
4. Move the deflection yoke (DY) backward and adjust the

purity control so that green is in the center and blue and
red are at the sides evenly.

5. Then move the DY forward and adjust so that the entire

screen becomes green.

6. Now switch over raster signal to red then blue and

confirm the condition.

...................................................................................................................................................................................................................... ...........

5. Oscilloscope
6. Landing Checker
7. XCV Adjuster

Purity control

Red

Blue

Green

7. When the position of the DY is determined, tighten it

with the DY mounting screw.

8. If the beam does not land correctly in all corners of the

screen, use magnet disc to correct it.

Preparation :
• Before starting, perform FOCUS adjustment.

• Picture mode STANDARD.

• Receive dot/cross hatch pattern.

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

Center dot

R    G    B

R

G

B

4 pole magnet

C/CV Board

– 17 –

1. (Moving vertically), adjust the 4 pole magnet to

converge red, green and blue dots in the center of the
screen.

2. Tilt the 4 pole magnet and adjust static convergence to

open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow A and B, the red, green and blue dots moves as
shown below:

If the blue dots does not converge with the red and green
dots, use the 6 pole magnet to adjust in the manner
described below.

R

R

G

G

B

B

A

B

B

A

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

6 Pole Magnet

4 Pole Magnet

DY pocket

Purity

6 Pole

Magnet

4 Pole

Magnet

Preparation :
• Before starting this adjustment, adjust the horizontal

and vertical static convergence.

Input cross hatch pattern.
i)

TLH
Adjust the horizontal convergence of red and blue dots
by inserting TLH Correction Plate to the DY pocket (left
or right).

ii)

YCH
Adjust YCH to balance Y axis.

iii) TLV

Adjust the vertical convergence of red and blue dots.

iv) XCV

Adjust XCV to balance X-axis.

Affix a Piece A (90), Convergence Correct/Permaloy Assy
Correction to the misconverged areas.

TLV

R B

YCH

R

B

XCV

B

R

TLH

B

R

TLV

ON DY:

TLV

XCV

YCH

DY pocket

DY pocket

TLH Plate

XCV

b

a

c

d

a-d : screen-corner
        misconvergence

a1~d1:Piece A (90), Convergence Correct

or

Permaloy Assy Correction

a1

b1

c1

d1

B

R

G

G

R

B

– 18 –

FOCUS adjustment should be completed before W/B
adjustment.

1. Receive digital monoscope pattern.
2. Set Picture Mode to "VIVID".
3. Adjust focus VR to obtain a just focus at the center of

the screen.

4. Change the receiving signal to white pattern and blue

back.

5. Confirm magenta ring is not noticeable. In case magenta

ring is obvious, then adjust FOCUS VR to balance
magenta ring and FOCUS.

1. Set the following condition:

– Picture and Brightness to "STANDARD".
– TV to Video mode.
– WHBL 016 "RGBB" to 01

2. Connect R, G, B of the C/CV board cathode to

oscilloscope.

3. Adjust Brightness to obtain the cathode value to the

value stated below.

4. Adjust SCREEN VR on the FBT until the scanning line

disappears.

5. Finally set WHBL 016 "RGBB" back to 00.

170 – 2VDC

1. Set to Service Mode.
2. Input white raster signal using signal generator.
3. Set the following condition:

Picture "VIVID", PICT 006 "WTS" to 00.

4. At Highlight condition, select WHBL 02 "RDRV" and 03

"GDRV" with 1 and 4 button of the remote
commander then adjust the data with 3 and 6 button.

5. At Cutoff, select WHBL 000 "BKOR" and 001 "BKOG"

and adjust the data.

6. Perform adjustment at Highlight and Cutoff condition

until it reaches its target.

7. Write data into memory by pressing [MUTING] 

t -.

8. Finally set PICT 006 "WTS" back to its original data.

1. Set TV to RF mode.
2. Input PAL monoscope to RF mode.
3. Set Brightness 50% and Picture to "MINIMUM".
4. Select WHBL 010 "SBRT" with 1 and 4 button of the

remote commander and adjust its data with 3 and 6
so that cut-off level is 10 IRE, slightly glimmer: 20 IRE
Then +2 steps offset.

5. Write into the memory by pressing [MUTING] 

t -.

VIVID : 45000K + 8 MPCD

Center data :

X : 0.2444
Y : 0.2466

– 19 –

ii.

PIP Model (KV-HG21M86)

line 1 and line 2 is same as above. Only line 3 is different same as SP model. Refer as below:

When VIF category is selected

Service adjustments to this model can be performed using the supplied remote commander RM-GA002.

With the unit on standby
i.

NON PIP Model (KV-HG21M81/M85)

service data

NVM

field

channel no./

category

in decimal

item name

in decimal

NG

service command

frequency

video input name

GEOM

006

HSIZ

031

x

SERVICE

60

S VIDEO 1

software

service data

reserved

power on time

release ID

version

in binary

for factory

color system

(decimal)

SGA01

0.69 *

0001 1111

FF FF

NTSC3

65535

Status SID,LOCK,SL

status

status

status

0:not locked

IVW,

WBC,

status

S/N LEVEL status status

DCXO Flash

Status Display

(no signal)

IVWF

HBC

BCF

(0-7)

GL

PTW

Value

Area

111

11

11

1

7

1

1

FG

xy 111 000000   000000

S _ _ : BX1S Sony
A _ _ : BX1S Aiwa
L _ _ : BX1L Full
B _ _ : BX1L Basic
D _ _ : DVD Combo
Z _ _ : Sound Special
_ U S :  US
_ N T : Taiwan/Philippines
_ T R : Latin/Brazil
_ G A :General Area

Serial no. of the M/P release
for each destination :
0X: use for FY03
1X: use for FY04
2X: use for FY05
3X: use for FY06
4X: use for FY07

U : USA - English/Spanish/French/Portuguese (typically)
A : GA - English/Arabic/Persian
M : GA - English/Simplified Chinese/Thai
R : GA - English/Russian/Vietnamese
H : NTSC - English/Complicated Chinese

1 1

1

Needed for Nicam DCXO alignment Purpose

x

y

Value of x=0 -Unknown, 1-NICAM, 2-A2, 3-KOREAN, 4-US, 5-Japan, 6-AV Stereo
Value of y=0 -Mono, 1-Stereo, 2-Bilingual, 4-SAP/Single

F G

DCXO Flash Value

N

NR table status (0-9) NR Table Indication

Disp. Table

Condition

0

NR0

3D Intell Pic Off + PAL4.43

1

NR1

3D Intell Pic On + PAL4.43 + SN=6,7 (Video)

2

NR2

3D Intell Pic On + PAL4.43 + SN=5

3

NR3

3D Intell Pic On + PAL4.43 + SN=4,3

4

NR4

3D Intell Pic On + PAL4.43 + SN=2,1

5

NTSC0

3D Intell Pic Off + NTSC3.58

6

NTSC1

3D Intell Pic On + NTSC3.58 + SN=6,7 (Video)

7

NR1_RF

3D Intell Pic On + PAL4.43 + SN=6,7 (RF)

8

NTSC1_RF 3D Intell Pic On + NTSC3.58 + SN=6,7 (RF)

9

NR_NA

Not PAL4.43 NTSC3.58

line 1

line 2

line 3

Status SID,

NR

LOCK,SL

status

status

table

status

0:not locked

IVW,

WBC,

status status S/N LEVEL status status

DCXO Flash

Status Display

(no signal)

IVWF

HBC

(0-9)

BCF

(0-7)

GL

PTW

Value

Area

111

11

11

N

1

7

1

1

FG

xy 111 000000   000000

Signal

S/N

Booster

before

Status

signal

0:Off;1:On

booster on.

111

11

11

1

7

1

1

FG

xy 111

1

A

F

2

5

AGC value

S/N

captured

after signal

before

booster

signal

on

line 3

line 3

Same as other category