DOWNLOAD Sony KV-DA292M86 Service Manual ↓ Size: 17.27 MB | Pages: 127 in PDF or view online for FREE

– 16 –

If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will be
reset to its original setting (shipping condition)

There are 2 ways to access to the "RESET" Function:-

a) By pressing "RESET" button on the Remote Commander.
b) By pressing "MENU" button on the Front Key Input and hold it down for 5 seconds.

(DAXXMXX doesn't have this function anymore.)
(DAXXNXX, DAXXKXX still have it.)

Sequential to the resetting operation, TV set would shut down once and automatically turn on again. The power-off
duration is expected to be about 500msec. Initial Setup Menu is displayed.
As a result, some items will be reset to an initial condition (shipment condition) wheareas some other remains at
the last selection by user.

Items that remains at the last selection by user

Reset Items

Program No., PICTURE POSITION (included PICTURE

ROTATION and PICTURE V-POSITION), OSD Language, Fine

tuning,TV System, Skip, Program label, Program sorting, Video

label, Program block (NTSC model)

Video input

RF user last setting

Volume

25

DRC-MF

DRC1250

Picture mode

DYNAMIC

3D Intelligent Picture

ON

Sound mode

DYNAMIC

Intelligent volume

OFF

Surround

OFF

Wide mode

4.3

Auto wide

ON

Twin

OFF

Program Index

OFF

* Program Block

Reset particular channel to
unblock

WEGA Theatre Setup

Direct Input

Video 1

Speaker

Main

Game mode

OFF (Video) *Not available in RF
mode

Color System

Reset to Auto at the CH, others
keep user setting

Eco mode

OFF

Wide mode

Wide zoom

Auto wide

ON

4.3 Default

Wide zoom

V Center

00

V Size

00

Picture mode

RF user last setting

Mute

OFF

OSD Display status

OFF

Main volume

25

Center-in volume

25

(Remote button)
Center speaker

Main or center in (No menu display)

(UNDER WEGA

(Selected only when WTM turns on)

THEATRE SETUP MENU)
Initial setup menu

Reactivate/ON

Twin size

Center

*= Reset only during watching time

- For Multi model only
- Not reset for NTSC model

Category

Default

Category

Default

– 17 –

• The following adjustments should be made when a

complete realignment is required or a new picture tube is
installed.

• These adjustments should be performed with rated

power supply voltage unless otherwise noted.

Controls and switches should be set as follows unless
otherwise noted:
PICTURE control ..................................................  normal
BRIGHTNESS control ..........................................  normal

Perform the adjustments in the following order :

1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note :  Test Equipment Required.

1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope

Preparation :
• In order to reduce the influence of geomagnetism on the

set's picture tube, face it east or west.

• Switch on the set's power and degauss with the

degausser.

1. Input a white signal with the pattern generator.

Pic mode : Dynamic

2. Position neck assy as shown in Fig 6-1.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the

purity control so that the green is at the center and the
blue and the red take up equally sized areas on each
side.
(See Figures 6-1 through 6-3.)

5. Move the deflection yoke forward and adjust so that the

entire screen is green. (See Figure 6-2.)

6. Switch the raster signal to blue, then to red and verify the

condition.

7. When the position of the deflection yoke has been

decided, fasten the deflection yoke with the screws and
DY spacers.

8. If the beam does not land correctly in all the corners, use

a magnet to adjust it.
(See Figure 6-4.)

Neck assy

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

Red

Blue

Green

Purity control
corrects this area.

Disk magnets or rotatable
disk magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

a

b

b

c

c

d

d

a

– 18 –

Preparation :
•

Before starting this adjustment, adjust the focus,
horizontal size and vertical size.

•

Receive cross hatch/dot pattern and set picture mode to
"STANDARD".

1. (Moving horizontally), adjust the H.STAT control so that

the red, green and blue dots are on top of each other at
the center of the screen.

2. (Moving vertically), adjust the V.STAT magnet so that the

red, green and blue dots are on top of each other at the
center of the screen.

3. Adjust Horizontal Trapezoid with “DEF1 005 HTPZ” in

Service Mode to make H-Trapezoid distortion best.

4. If the H.STAT variable resistor cannot bring the red,

green and blue dots together at the center of the screen,
adjust the horizontal convergence with the H.STAT
variable resistor and the V.STAT magnet in the manner
given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform
adjustments while tracking.)

1

V. STAT

2

H. STAT VR

3

Center dot

R    G    B

R

G

B

H. STAT VR

V. STAT

Magnet

RV702

H. STAT

Y magnet

C Board

R

R

G

G

B

B

a

a

b

b

b

R

R

G

G

B

B

a

b

R

R

G

G

B

B

a

a

b

b

b

V.STAT

Purity

BMC (Hexapole)

– 19 –

(2) Dynamic Convergence Adjustment
Preparation:
•

Before starting this adjustment, adjust the horizontal
static convergence and the vertical static convergence.

•

Set the PICTURE and BRIGHTNESS to normal.

1

Receive the dot/hatch pattern signal and adjust picture
quality by the menu.

2

Correct horizontal mis-convergence of red and blue of
both sides on the X axis.
When red is outside insert TLH convergence piece to
right side (TLH +) views from DY neck. And when blue is
outside, insert it to left side (TLH –) and take both sides.

To able to become balance of XCV on the X axis well.

Correct the vertical mis-convergence of red and blue of
vertically sides on the Y axis.

Adjust horizontal mis-convergence of red and blue of
vertically sides on the Y axis. Mentioned above steps 2 to
4 are adjusting respectively perform minuteness tracking.

4

BMC (Hexapole) Magnet.
If the red, green and blue dots are not balanced or
aligned, then use the BMC magnet to adjust in the
manner described below.

5

Y separation axis correction magnet adjustment.

1. Receive the cross-hatch signal and adjust [PICTURE] to

[MIN] and [BRIGHTNESS] to [STANDARD].

2. Adjust the Y separation axis correction magnet on the

neck assembly so that the horizontal lines at the top and
bottom of the screen are straight.

Note
1. The Red and Blue magnets should be equally far from

the horizontal center line.

2. Do not separate the Red and Blue magnets too far.

(Less than 8 mm)

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

Neck assy

Neck assy

Red

Red

VM Board

VM Board

Blue

Red

Blue

Blue

R

(B)

B

(R)

B

(R)

R

(B)

b

a

c

d

a-d : screen-corner
        misconvergence

(VR1)
TLV1 (no need to adjust)

DY pocket

TLH Plate

(VR3)

TLV2

(XCV)

(VR2)

YCH