DOWNLOAD Sony KV-DA292M86 Service Manual ↓ Size: 17.27 MB | Pages: 127 in PDF or view online for FREE

– 4 –

[+B overcurrent OCP ]

Occurs when an overcurrent on the +B(135) line is detected by Q6804.
If Q6804 go to ON, the voltage to the pin57 of IC4301 go to "HIGH".
The unit will automatically turn off.

[High voltage protector of Horizontal Deflection]

Occurs when an overvoltage of horizontal pulse is detected by D6809.
If the voltage of anode D6809 and D6843 goes to High, the voltage to pin57
of IC4301 go to "HIGH".
The unit will automatically turn off.

[+B overvoltage OVP ]

Occurs when an overvoltage on the +B(135) line is detected by D6635 and
Q6606. If Q6606 go to ON, the voltage to pin6 of IC001 go to "HIGH". The
unit will automatically turn off.

[Vertical deflection failure]

Occurs when an absence of the vertical deflection pulse is detected by
Q6808 and R6910. Shut down the power supply.

[White balance failure]

If the RGB levels do not balance or become low level within 5 seconds. This
error will be detected by IC4301.
TV will stay on, but there will be no picture.

[5V/9V failure]

Occurs when 5V/9V is not supplied to Micon (IC001).
No raster will be detected or no picture.

5

8

1.

Display self diagnostic screen

[Display] t [Channel    ] t [Volume    ] t [Power / TV]

2.

Stop standby flash

i) Turn off power switch on main.
ii) Unplug power cord from the outlet.

3.

Clear fault result

In self diagnostic screen, press 

[Channel    ] t 

-

4.

Quit self diagnostic screen

Turn off power switch of remote commander or main unit.

[V] Q6808, R6910

[OCP] Q6804, D6821

[H] D6808, D6809

– 5 –

2 Rear cover   

1 Twelve screws

(BVTP 4 

× 16)

2

 Two screws

     (Washer Head)
     (+P4 

× 16)

1

 Two screws

     (BVTP 4 

× 16)

5 One Screw
     (+BVTP 3 

× 12)

6 Three Hooks

3 One screw
     (+BVTP 4 

× 16)

4 Five screws
     (+BVTP 3 

× 12)

2 Terminal Bracket

1 One screw
     (+BVTP 3 

× 12)

2

 J Board

1

 Five Screws

     (+BVTP 3 

× 12)

– 6 –

2 Two clips

BH1 Board

1 F1 Board

2 Four Hooks

1 Three Hooks

2 

DL Board

3 Five Hooks     

4 

H1 Board

    

1 

H2 Board

2 Four
     Hooks

2 Five screws
     (BVTAP 3 

× 12)

1 One screw
     (washer head)
     (+P 3 

× 12)

6 Five Hooks

4 A Board

5 D Board

3 Three
      Hooks

1

 BH1 Board

4

 BC Board

6

 BP Board

5

 Two 

Hooks

3

 Two Hooks

1

 Two Hooks

– 7 –

• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield

or carbon paint on the CRT.

• REMOVING PROCEDURES

1 Turn up one side of the rubber cap in the direction

indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direction

indicated by the arrow b.

3 When one side of the rubber cap is separated from the

anode button,  the anode-cap can be removed by turning
up the rubber cap and pulling it up in the direction of the
arrow c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with sharp

2 Do not press the rubber too hard so as not to damage

3 Do not turn the foot of rubber over too hard.

• Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom right

and left.

• When removing the Nut Locking: first make sure to hold the Nut special CRT with a spanner while opening the Nut Locking

using a torque driver. Then proceed to remove the Nut special CRT using a torque driver.

1) Remove the Rear Cover.
2) Unplug all interconnecting leads from the Deflection Yoke, Neck Assy, Degaussing Coils and CRT grounding strap. Remove

Chassis Assy

3) Place the TV set with the CRT face down on a cushion (jig).

qa

 Earth Coating Assy

q;

 Degaussing Coil

4

 Anode Cap Removal

5

 C Board Removal

qs

 Spring Tension

(2) Removal

qd

 

Support, CRT Removal (x2)

9

 Holder, DGC

     Removal (x2)

qf

 Screw, Tapping 7 +

     Crown Washer (4)

7

 Loosen the Deflection Yoke

fixing screw and remove

8

 Band, DGC Removal

6

 Loosen the Neck Assembly

     fixing screw and remove 

Neck Assy & VM board Removal

a

a

b

b

c

 Anode Button