DOWNLOAD Sony KV-BZ213M10 Service Manual ↓ Size: 15.96 MB | Pages: 127 in PDF or view online for FREE

– 8 –

 

Lead Assy, Focus

For 1 Speaker models

For 2 Speaker models

HV Cable

FBT Flange

Make sure rubber cap is pushed

down to make sure it covers

the FBT flange completely

FBT Flange

RY600

540 ± 5 mm

AC Cord Holder

Dress AC Power Cord with Standing Purse

Lock, followed by Lead Assy, Earth.

Dress AC Power Cord and Lead

Assy, Speaker with Pin, Wire A016

Dress AC Power Cord with

Standing Purse Lock, followed

by Lead Assy, Earth and Lead

Assy, Speaker (RED+BLK).

Dress AC Power Cord

and Lead Assy,

Speaker (WHT+BLK)

with Pin, Wire A016

Caution: Dress above capacitors'

height as shown

Keep wires above of RY600 ---> to avoid wires from

being sandwiched with front jack and pushed against relay

2-4(i)

2-4(ii)

RY600

– 9 –

Earth Assy,
Coating

Make sure the
round side of 
spring tension 
is installed to 
Earth Assy, 
coating

For 2 Speaker models

For 1 Speaker models

 

 

 

 

 

 

 

.

Dress wires away from beznet's front terminal --> prevent wires

from being sandwiched when docking chassis.

Standing purse lock

Standing purse lock

DGC Conn

Lead Assy,

Speaker (RED+BLK)

DGC

Lead Assy,

AC Power Cord

Lead Assy, Earth

AC Power Cord

Dress AC Power

Cord and Lead

Assy, Speaker (left)

with Pin, wire A016

Make sure Lead Assy, Earth is kept

away from group of heatsinks

Dress DGC Conn together with AC Power Cord, Lead Assy, Earth

and Lead Assy, Speaker (RED+BLK) which are dressed during

Chassis Assy as shown in Figure 2-4(ii)

Dress DGC Conn together with AC Power Cord and Lead Assy,

Earth which are dressed during Chassis Assy as shown in 

Figure 2 4(i)

Make sure Lead Assy, Earth is kept

away from group of heatsinks

Dress AC Power

Cord and Lead

Assy, Speaker (left) 

with Pin, wire A016

CAUTION :
1. Prevent wires from being sandwiched with
  beznet's front terminal when docking chassis.
2. Dress speaker wires above capacitors
  near it --> prevent from touching high-temp
  parts.

– 10 –

 

 

 

 

 

For illustration 

 

 

 

 

Black tape

Ensure DGC

Connector is kept

behind of DGC

DGC Connector in front of DGC before

dress with standing purse lock.

Make sure wire does not touch heatsink

or other high temperature parts

Standing purse lock

AC Power Cord

Lead Assy, Earth

DGC Conn

Lead Assy, Speaker

For 2 Spk models

For 1 Speaker models

Purse lock

Spring extension

Left Speaker

Lead Assy, Speaker

DGC Conn

Right Speaker

Keep Lead Assy,

Speaker (RED+BLK)

Ensure wires are

kept away from heatsink

Lead Assy, Speaker (RED+BLK) is

sandwiched between DGC & CRT surface

Insert Lead Assy, Speaker (WHT+BLK)

followed by AC Power Cord into CRT

support's hook. Make sure Lead Assy,

Speaker (WHT+BLK) is secured behind 

AC Power cord

Keep wires away from sharp

edge of spring extension --> to

prevent scratching on wires.

Lead Assy

Left Speaker

Insert AC Power Cord into CRT support's hook

For 2 Speaker models

Ensure DGC
Connector is
kept behind of
black tape.

Earth Assy, Coating is in

front of DGC before looping

it once around DGC.

Earth Assy, Coating is in

front of DGC before looping it

once around DGC.

Connected

to C board.

From braided wire of

Earth Assy, Coating

Earth Assy, Coating

Dress Connector Assy,

7P with cable tie at

alignment hole A. Make

sure end of cable tie is

facing inwards

-->

 

to prevent rattle sound  

Ensure Earth Assy, Coating is close

to CRT surface before making a

loop around DGC

DGC

CAUTION :
1. Prevent cable tie from touching
rear cover or any enclosures by
turning them away from it
--> to avoid ratlle sound & prevent
cable tie from touching solder side
of board.

– 11 –

 

 

 

Top switch wire

under DGC & right

of black tape

Dress Top Switch wire
around AC Power Cord
--> keep away from heatsink

Top switch wire

under DGC & left of

black tape

Black tape

Earth Assy, Coating

1) DY Connector goes
underneath of Earth Assy,
Coating and Connector Assy,
5P (200V) wire.

Make sure DY Connector is on

the right side of Earth Assy, coating

3) Dress DY Connector
and Connector Assy, 5P
(200V) wire with Purse 
lock Ø5

Purse Lock Ø5

Dress wires

away from

FBT area

Use heatsink height to

estimate purse lock

location

2) DY Connector goes above
Connector Assy, 5P (200V) wire

Conn Assy, 5P

DY Connection

Conn Assy

, 

5P

(200V)

DY

 Connector

TVSR (Clause 9.4.7):
All wiresmust be kept away from FBT
area by a distance of 10mm or more.