DOWNLOAD Sony KP-57WV600 (serv.man2) Service Manual ↓ Size: 13.67 MB | Pages: 127 in PDF or view online for FREE

Model
KP-57WV600 (serv.man2)
Pages
127
Size
13.67 MB
Type
PDF
Document
Service Manual
Brand
Device
TV
File
kp-57wv600-sm2.pdf
Date

Sony KP-57WV600 (serv.man2) Service Manual ▷ View online

— 18 —
KP-57WV600
2-6.  2-POLE MAGNET ADJUSTMENT 
1.  Set the picture mode to PRO and picture to MAX.
2.  Receive the Dot signal.
3.  Cover the red and blue CRT lenses with lens caps to allow only green 
to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).
4.  Turn the green focus VR on the focus block to the left (counter 
clockwise) and set it to overfocus to enlarge the spot.  
5.  Adjust the green CRT’s 2-pole magnet so that the small bright spot is 
in the center.
6.  Align the green focus VR on the focus block and set it for the best 
focus.
7.  Repeat steps 1 through 6 for the red CRT except now you will cover 
the green and blue CRT lenses with lens caps to allow only red to 
show (or use the method shown in the note below  
for turning 
off the CRTs individually without using lens caps) and you will adjust 
the red focus control on the focus block.
8.  Repeat steps 1 through 6 for the blue CRT except now you will cover 
the red and green CRT lenses with lens caps to allow only blue to 
show (or use the method shown in the note below  
for turning 
off the CRTs individually without using lens caps) and you will adjust 
the blue focus control on the focus block.
Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2170P-2 1 RGBS.
2-7.  CENTERING MAGNET ADJUSTMENT
1.  Set the picture mode to PRO.
2.  Receive the monoscope signal.
3.  Cover the red and blue CRT lenses with lens caps to allow only green 
to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).
4.  Adjust the green CRT’s centering magnet to put the center of the 
monoscope signal to the center of the screen.
5.  Repeat steps 1 through 4 for the red CRT except now you will cover 
the green and blue CRT lenses with lens caps to allow only red to 
show (or use the method shown in the note below  
for turning 
off the CRTs individually without using lens caps) and you will adjust 
the red centering magnet.
6.  Repeat steps 1 through 4 for the blue CRT except now you will cover 
the red and green CRT lenses with lens caps to allow only blue to 
show (or use the method shown in the note below  
for turning 
off the CRTs individually without using lens caps) and you will adjust 
the blue centering magnet.
Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2170P-2 1 RGBS.
2-8.  4-POLE MAGNET ADJUSTMENT 
1.  Set the picture mode to PRO and picture to MAX.
2.  Receive the Dot signal.
3.  Cover the red and blue CRT lenses with lens caps to allow only green 
to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).
4.  Turn the (green) focus VR on the focus block to the right (clockwise) 
and set it to under-focus to reduce the spot.
5.  Adjust the 4-pole magnet so that the small spot in the center of the 
screen becomes round for green and red.
6.  Adjust the blue spot to an oval shape X:Y=1:1.2
7.  Repeat steps 1 through 6 for the red CRT except now you will cover 
the green and blue CRT lenses with lens caps to allow only red to 
show (or use the method shown in the note below  
for turning 
off the CRTs individually without using lens caps) and you will adjust 
the red focus control on the focus block.
8.  Repeat steps 1 through 6 for the blue CRT except now you will cover 
the red and green CRT lenses with lens caps to allow only blue to 
show (or use the method shown in the note below  
for turning 
off the CRTs individually without using lens caps) and you will adjust 
the blue focus control on the focus block.
Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2170P-2 1 RGBS.
x
y
x : y = 1:1 (Green, Red)
Use the center dot
2-9.  DEFOCUS ADJUSTMENT (BLUE)
Note: Adjust the blue dot to be slightly larger than red and green dots. 
This adjustment provides a more pleasing picture to the customer.
1.  Set the picture mode to PRO.
2.  Receive the Dot signal.
3.  Cover the red and green CRT lenses with lens caps to allow only blue 
to show (or use the method shown in the note below for turning off 
the CRTs individually without using lens caps).
4.  Turn the blue focus VR on the focus block to the right (clockwise) to 
make the round dot elliptical.
5.  Check the flare with a high luminance signal to make sure the flare is 
minimal while the dot shape is elliptical.
6.  Set the generator to an all white signal and check uniformity.
Note: If lens caps are unavailable, you can cut off the unnecessary color 
beams by controlling the service mode 2170P-2 1 RGBS.
x
y
x : y = 1:1.2 (BIue)
Use the center dot
— 19 —
KP-57WV600
2-10. ELECTRICAL ADJUSTMENTS BY 
 
REMOTE COMMANDER
All of the circuit adjustments can be made by using the remote 
commander (RM-Y188).
NOTE : The following test equipment is required: 
1.  Pattern Generator (with component outputs)
2.  Frequency counter
3.  Digital multimeter
4.  Audio oscillator
2-10-1.METHOD OF ENTERING THE SERVICE 
ADJUSTMENT MODE
SERVICE MODE PROCEDURE
1.  TV must be in Standby mode. (Power off)
2.  Press “DISPLAY”, “5”, “VOL +”, then “POWER” on the remote 
commander. 
  (Press each button within 1 second of pressing the previous button.)
SERVICE MODE ADJUSTMENT
Data
WSL : XXX
0     0
3D-COMB
NRMD
F / A FLAG : XXXXXXXX
CBA FLAG : XXXXXXXX
SERVICE
TV
Item NO.
Adjustment Item
Category
3.  The screen displays the item being adjusted within that category.
4.  Press 1 or 4 on the remote commander to select the adjustment item
5.  Press 3 or 6 on the remote commander to change the data
6.  Press 2 or 5 on the remote commander to select the adjustment 
category
  Every time you press 2(Category up), service mode changes in the 
order shown below:
3D-COMB
2103-1
VERSION
2103-2
2170P-1
2170P-2
2170P-3
2170D-1
2170D-3
2170D-4
D-CONV
2151
2170D-5
OP
ID
DRCV
2170D-2
2170P-4
PJED FDIS
PJED ROGH
GRN CENT
3DNR
CCP
AUDIO
SNNR
MID1
MID2
MID3
MID5
CXA350GR
7.  If you want to go back to the most recently saved value, press “0” 
then “ENTER” to read the memory.
8.  Press “MUTING” then “ENTER” to write the new adjustment data into 
memory.
9.  Turn power off when you want to exit the service mode.
Note: Press “8” then “ENTER” on the remote commander to restore the 
factory settings for user controls and channel memories (this will also 
turn set off and then on to exit the service mode).
2-10-2.MEMORY WRITE CONFIRMATION 
     METHOD
1.  After adjustment, turn the power off with the remote commander.
2.  Turn the power ON and set to service mode.
3.  Cycle through the adjusted items again and confirm that the 
adjustments were saved.
2-10-3.ADJUSTING BUTTONS AND 
 INDICATOR
Note: When the PJE mode (which displays an internally generated 
signal) is activated, several buttons on the remote commander will have 
different functions than the ones listed below. Therefore, when in the 
PJE mode, refer to section 2-12-3 for button functions.
MUTING
Category up
Adjustment 
item up
Adjustment 
item down
ENTER
Category 
down
Data down
Data up
DISPLAY
POWER
Test Reset
VOLUME
TV/VIDEO
PIC MODE
ANT
WIDE MODE
INDEX
TWIN VIEW
    RM-Y188
— 20 —
KP-57WV600
SERVICE DATA LISTS 
2-11                                       
��������
����
�����������
����
�������
���
������������������������
����
������
����
��������������������
����
�������������������
����
���������������������������������������
���
�����������������������
����
��������������������
����
������������������������
����
�������������������������������
���
���������������������
����
�������������������������
��������
� ��������
� ��������
� ��������
����
�����������������������
��������
�� ��������
�� ��������
�� ��������
��
�� ����
�������������������������
��������
� ��������
� ��������
� ��������
�� ����
�����������������������
��������
� ��������
� ��������
� ��������
�� ���
����������������������
�� ���
�������������������������������
�� ����
������������������������
�����
� ��������
� �����
� ���
�� ����
�������������������������������������
�����
� ��������
� �����
� ���
�� ����
��������
�� ����
������������������������������
��
�����
� ��������
� �����
� ���
�����
�����
� ��������
� �����
� ���
����
�� ����
������������������
��
�����
� ��������
� �����
� ���
����
�� ����
����������������������������������
�� ����
��������������������������������
�� ����
�������������������������
�� ����
�����������������������
�� ����
����������������������
�� ����
���������
�������������
�����
���
��������
�����
�����


���





— 21 —
KP-57WV600
SERVICE DATA LISTS 
��������
����
�����������
����
���������
����
�����������������������
�� ������
��
����
����������������������
�� ������
��
��������
����
������������
� ������
����
���������
� ������
����
�������
� ������
��
����
���������
� ������
����
���������������
��������������
�� �������������
� ���������
� ��������������
��
����
������������
� �������������
� ���������
� ������
����
����������������������������������
� �������������
� ���������
� ������
����
����������������������������������
�� ����
���������������������������������
�� ����
������������������������������
�����
� ������
�� ����
��������������������������
�� ���
�����������������������������������
�� ����
���������������������
� ��
� ������
�� ����
�����������������������
� ��
� ������
�� ����
�����������������������
� ��
� ������
� ��������������������
�� ����
���������������������������������
� �������������
� ���������
� ������
�� ����
�������������������������������
�� ����
��������������������������������
� ������
� ���������
� ������
�� ����
���������������������������������
�� ������
��
�� ����
���������������������������������
�� ������
��
�� ����
����������������������������������
�� ����
��������������������������������������
�� ����
�������������������
��������������
� ������
� ����
� ����
� ����
��������������������������������
���������������
���������������
���������������
���������������
�� ����
���������������������
��������������
� ����
� ����
� ����
� ����
��������������������������������
���������������
���������������
���������������
���������������
���������
����
�����������������������
����
�� ����
��
����
����������������������
����
� ����
��
� �������������������������������������������������������������
�������
����
������������
�������
� ��������
� ����������������������������������������������
����
���������
�������
� ��������
����
�������
�������
� ��������
��
�� ����������������������������������������
����
���������
�������
� ��������
����
���������������
�������
� ��������
����
������������
�������
� ��������
����
����������������������������������
�������
� ��������
����
����������������������������������
�� ����
���������������������������������
�� ����
������������������������������
�������
� ��������
�� ����
��������������������������
�� ���
�����������������������������������
����
� ����
�� ����
���������������������
�������
� ��������
�� ����
�����������������������
�������
� ��������
�� ����
�����������������������
�������
� ��������
�� ����
���������������������������������
�������
� ��������
�� ����
��������������������������
�� ����
��������������������������������
�������
� ��������
�� ����
���������������������������������
�� ����
���������������������������������
��
�������������
�������������
�����
�����
���������
���������
������
������
������
�����
�����
�����
������������������������
�������������������������������
������������������������
������������������������
�������������������������������
������������������������


��
��
�����
�����
�����
��
��
Page of 127
Display

Click on the first or last page to see other KP-57WV600 (serv.man2) service manuals if exist.