DOWNLOAD Sony KP-48V85 / KP-53V85 / KP-61V85 Service Manual ↓ Size: 10.89 MB | Pages: 105 in PDF or view online for FREE

– 17 –

Insert two size AA (R6) batteries (supplied)
by matching the + and – on the batteries to
the diagram inside the remote control’s
battery compartment.

• Remove the batteries to avoid damage

from possible battery leakage whenever
you anticipate that the remote control
will not be used for an extended period.

• Handle the remote control with care.

Avoid dropping it, getting it wet, or
placing it in direct sunlight, near a heater
or where the humidity is high.

• Your remote control can be programmed to

operate most video equipment.
(see “Operating Video Equipment” on
page 55)

The supplied remote control has a joystick
which moves the on-screen selector in four
directions. In most cases, moving the joystick
up, down, left or right will cause the selector
to move in the selected direction.

In some cases, the selector may move in four
directions according to the function. Pressing
down on the center of the joystick (

) will

activate the selected item.

You may also move the joystick right to
activate a selected item. (There are some
exceptions to this option.)

.

When menu items present a slider ( 

 or

), move the joystick up, down, left or

right to adjust the setting.

Several menu windows will provide
prompts and instructions to assist you in
navigating through the different functions.

The AUTO SET UP feature will allow you to
set the on-screen language and set all
receivable channels.
The AUTO SET UP feature does not apply for
installations that use a cable box for all channel
selection.

Notes:
• Before you perform AUTO SET UP again,

make sure that the input from ANT (not
AUX) is selected by pressing ANT until
“AUX” does not appear next to the
channel number.

• Perform this function during the day,

with the antenna and/or cable properly
connected, to ensure that all available
channels will be broadcasting and
receivable.

• When you perform AUTO SET UP, all the

settings in the Video, and Audio menus
are reset to the factory settings.

Using the buttons on the front panel of the
projection TV:

Press POWER to turn on the projection
TV.
The AUTO SET UP screen appears.

Press CHANNEL +  to select English,
CHANNEL –  to select Español or
VOLUME +  to select Français.

The screen will change to reflect your
choice.

Press VOLUME –  to continue.

Press CHANNEL + to preset channels
automatically.

“Auto Program” appears and the
projection TV starts scanning and
presetting channels automatically. While
scanning, the received channel will be
displayed on the sub screen. When all the
receivable channels are stored, the lowest
numbered channel is displayed.

Press  [ SET UP ]  to exit.

First please connect
 the  antenna.

A u t o   S e t   U p   :

E s p a ñ o l   :

E n g l i s h   :

F r a n ç a i s   :

  [ V O L – ]

  [ C H – ]

  [ C H + ]

  [ V O L + ]

A u t o   P r o g r a m

Oprima  [ SET UP ]  para
salir.

Primero conecte la
antena.

  [ V O L – ]

  [ C H – ]

  [ C H + ]

  [ V O L + ]

A u t o   S e t   U p   :

E s p a ñ o l   :

E n g l i s h   :

F r a n ç a i s   :

N o   :

A u t o   P r o g r a m   ?

C o n t i n u e   t o

Y e s   :

  [ C H – ]

  [ C H + ]

– 18 –

The projection tube image appears on the
screen in three layers (red, green and blue). If
they do not converge, the color is poor and
the picture blurs.

Before you use your projection TV, be sure to
adjust the convergence.

The FLASH FOCUS feature allows you to
adjust the convergence automatically.

 

 

 

 

  z

Press FLASH FOCUS.

The cross pattern appears and FLASH
FOCUS begins to work. The adjustment is
completed when the cross pattern becomes
white.

Note:
• FLASH FOCUS is canceled if you

perform any other function while FLASH
FOCUS is working.

Press SET UP inside the drop-down panel on
the projection TV and perform steps 2-4 on
page 23.

Press SET UP again to exit.

TV (FUNCTION)

TV POWER

CH +/–

VOL +/–

MUTING

Activates the remote control for use with the projection TV.

Turns the projection TV on and off. If a video input indication (e.g., VIDEO 1,
VIDEO 2) appears on the screen, press TV/VIDEO until a channel number
appears.

Use for direct channel selection. Press 0-9 to select a channel (for example,
to select channel 10, press 1 and 0). The channel will change after 2
seconds, or you can press ENTER for immediate selection.

Press to scan through the channels (+ up or – down).
Speed Surf
1

Press and hold CH + or – to change the channel number rapidly.

Release to display the desired channel.

Press to adjust the volume (+ up or – down).

Press to mute the sound. “Muting” will appear on the screen and will dim
three seconds later. To restore sound, press again or press VOL +.

Many TV features can be accessed directly
through the remote control. The following
chart will explain the function of some
buttons found on your remote control.

and ENTER

Press PICTURE MODE repeatedly to directly
choose one of five different video modes that
best suits the program you are watching.
Vivid: Select for enhanced picture contrast and

sharpness.

Standard: Select to display a standard

picture for normal viewing environments.

Movie: Select to display a finely detailed

picture for low light environments.

Personal 1, Personal 2: Select to customize

the “Picture Adjustment” of the Video menu
according to your personal preference.

When you select “Movie,” “Personal 1” and
“Personal 2,” you can also perform the “Picture
Adjustment” (such as “Brightness,” “Color,” etc.)
to suit your taste.  For details, see “Mode” on
page 34.

– 19 –

TV/VIDEO

JUMP

FREEZE

(yellow labeled
button)

DISPLAY

Press repeatedly to scroll through available video inputs:
TV, VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4 and VIDEO 5.
If you select “Skip” as a “Video Label” in the Set Up menu, your projection
TV will skip the video input you selected. (see “Video Label” on page 39)

Press to alternate or 

jump

 back and forth between two channels. The

projection TV will jump between the current channel and the last channel
selected using the 0-9 buttons.

This is useful when you need to copy down information that appears on the
TV’s screen.
Press to 

freeze

 the desired picture. The frozen picture is displayed on the left

of the screen while viewing the normal picture of the current channel on the
right.

Press again to display the normal picture.

Press to display the channel number, current time, channel caption (if set),
and MTS mode (if SAP is selected). The SAP indication disappears and the
other indications dim three seconds later.
To turn the display off, press DISPLAY again.

 

 

 

 

 z

R e c ip e 

f l o u r - - - - 2

s u g a r  -  -  -  1/2

s a l t - - - - - 1/2

b u t t e r - - - 1

6

 CC

(under the cover)

SLEEP

(under the cover)

ANT

(AUX input)

MTS/SAP

(under the cover)

TV/VTR

(under the cover)

SYSTEM OFF

(under the cover)

Press repeatedly to scroll through available displays:
XDS (Extended Data Service)

Displays a network name, program name, program type, program length,
program description, call letters and time of the show if the broadcaster
offers this service.

Displayed on the screen if the broadcaster offers this service. (see
“Caption Vision” on page 42)

“Off” appears and the display is canceled.

Press repeatedly until the projection TV displays the approximate time in
minutes (30, 60, or 90) that you want the projection TV to remain on before
shutting off automatically.
Cancel by pressing until “Sleep Off” appears.

Press to change between the VHF/UHF input and the AUX input. (for
detailed connection information, see “Cable and antenna” or “Cable box and
cable” on page 9)

Press to scroll through the Multi-channel TV Sound (MTS) options:
Stereo, SAP, Mono and Auto SAP. (see “MTS/SAP” on page 35)

Press to select an audio option:
Trusurround, Simulated and Effect Off. (see “Effect” on page 35)

Press when you are finished using a VCR and you want to switch to the TV
input. The VCR power will remain on.

Press to turn off the projection TV and all other equipment connected with S-
Link. (see page 20)

– 20 –

(under the cover)

(white labeled

 

button)

(white labeled
 button)

Press to display a window picture.
Each time you press this button, the picture size will change
(1/4 n1/9 n1/16 nno display).

To close the window picture, press 

 repeatedly until it disappears.

Press to change the location of the window picture (counterclockwise)
around the main picture.

Press to select either the main or window picture in order to change the
TV channel or video source using the white labeled buttons below. The
symbol “b” (or “B”) will appear to indicate which picture’s channel or input
mode can be changed.

To change the location of the window picture, move the joystick in any
direction and release it when the picture is in the desired location.

Press repeatedly to scroll through the available video inputs for the
picture on which the symbol “b” (or “B”) is displayed. (see “TV/VIDEO” on
page 26)

The Picture-in-Picture (PIP) feature allows
you to view two channels simultaneously,
one in the full size “main” picture and one in
a smaller “window” picture.

You can move the window picture to any
location on the screen. (Free Layout Picture-
in-Picture)

* It will dim in about 3 seconds.

 

 

 

 

 z

The symbol “≥”
indicates which
picture's sound is being
received.

The symbol “b” or “B”
indicates which picture's
TV channel or input
source can be changed.

6

10

(white labeled button)

(white labeled
button)

(under the cover)

Press to select the TV channel on which the symbol “b” is
displayed. (for details, see “Watching the TV” on page 25)
Speed Surf
1 Press and hold CH + or – to change the channel number rapidly.
2 Release to display the desired channel.

Press to change between the VHF/UHF input and the AUX input for the picture on
which the symbol “b” (or “B”) is displayed.

Press to alternate sound between the main picture and the window picture. The
symbol “

” will appear for a few seconds to indicate which picture’s sound is being

received.

This is useful when you need to copy down information of the main picture.
Press to freeze the desired scene in the main picture. The frozen picture is displayed
in the window picture while viewing the normal picture in the main picture.  The
window picture size is automatically changed to 1/4 if it was 1/9 or 1/16.
Press again to resume normal PIP viewing.

Press to switch the audio and video of the main picture and the window picture.
Each time you press SWAP, the picture and sound of the two will be exchanged.

• If one of the pictures received through

PIP is snowy, the entire screen may
become unstable. In this case, erase the
snowy channel. (see “Channel Skip/
Add” on page 39)

or

or

and ENTER