DOWNLOAD Sony KP-48V85 / KP-53V85 / KP-61V85 Service Manual ↓ Size: 10.89 MB | Pages: 105 in PDF or view online for FREE

– 14 –

Using an AUDIO and S VIDEO cables,
connect AUDIO and S VIDEO IN on the
projection TV to AUDIO and S VIDEO OUT
on the DVD Player (White-AUDIO Left, Red-
AUDIO Right).

Using an AUDIO cable, connect AUDIO of
LINE OUT on the DVD Player to AUDIO of
VIDEO 4 or 5 IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).

Using three yellow VIDEO cables, connect
Y, P

B

, and P

R 

of COMPONENT VIDEO

OUT on the DVD Player to Y, P

B

, and P

R

 of

VIDEO 4 or 5 IN on the projection TV.

• Since the high quality pictures on a DVD

disc contain a lot of information, picture
noise may appear. In this case, adjust “Noise
Reduction” in the Video menu. (see “Noise
Reduction” on page 30)

• Some DVD Player terminals may be labeled

differently. If so, connect as follows:
Connect Y (green) to Y.
Connect P

B

 (blue) to C

B

, C

b

 or B-Y.

Connect P

R

 (red) to C

R

, C

r

 or R-Y.

For greater control of all audio and video
equipment, connect an AV receiver.

Perform as described in “Connecting a

cable TV system/antenna to a VCR” on
page 6.

Using a VIDEO cable, connect VIDEO 1 IN
on the projection TV to MONITOR OUT
on the AV receiver.

Using an AUDIO/VIDEO cable, connect
TV OUT on the projection TV to VIDEO 2
IN on the AV receiver.

Using an AUDIO/VIDEO cable, connect
the video equipment to the AV receiver.

– 15 –

For more dynamic sound, connect an audio
system to the projection TV.

Using an AUDIO cable, connect AUDIO
(VAR/FIX) OUT on the projection TV to
one of the unused Line inputs (e.g. Tape-2,
AUX1, etc.) on the stereo.

Set the stereo to the chosen Line input and
use the Audio menu to set the audio
output and switch the TV’s speakers off.
(see “Audio Out” and “Speaker” on page 36)

Note:
• You can adjust VOLUME, “Bass,”

“Treble,” “Balance,” “MTS/SAP” and
“Effect” with the supplied remote control.
The control items except VOLUME can be
adjusted only when “Audio Out” is set to
“Variable” in the Audio menu. (see
“Audio Out” on page 36)

Use this connection to control the speaker’s
Dolby Pro Logic surround system and super
woofer mode with the remote control. (see
“Speaker” and “SAVA SP Control” on page
36)

HRD

CENTER
SPEAKER
IN ‘, ’

Using the AUDIO cable supplied with the
speaker to AUDIO (VAR/FIX) OUT on
the projection TV.

Using the CONTROL S cable, connect
CONTROL S IN on the speaker to
CONTROL S OUT on the projection TV.

If you use an amplifier with a Dolby Pro
Logic decoder instead of the projection TV’s
audio system, you can still use the projection
TV’s center speaker.

Using the speaker cords (supplied with
the amplifier), connect the speaker
terminals on the amplifier to CENTER
SPEAKER IN +/– on the projection TV.

Using an AUDIO cable, connect AUDIO
(VAR/FIX) OUT on the projection TV to
one of the unused Line inputs (e.g. Tape-
2, AUX1, etc.) on the amplifier (White-
AUDIO Left, red-AUDIO Right).

Set the amplifier to the chosen Line input
and use the Audio menu to set “Speaker”
to “Center” on the projection TV. (see
“Speaker” on page 36)

– 16 –

S-Link is a Sony innovation designed to
make the Sony components work together. It
allows you to automatically switch the
projection TV’s input mode to video when
you press the play button on the Sony S-Link
VCR.

Connect the Sony VCR (DVD). (see
“Connecting a cable TV system/antenna
to a VCR” on page 10 or “Connecting a
DVD Player with component video
output connectors” on page 16)

Using an S-LINK cable, connect the
S-LINK jacks on the VCR (DVD) and the
projection TV. Ensure that both ends are
seated firmly and that the projection TV’s
S-LINK jack is in the same row as the
AUDIO/VIDEO cable extending from the
Sony VCR (DVD).

Using a VIDEO cable, connect VIDEO 1
IN on the projection TV to MONITOR
OUT on the Sony AV receiver.

Using an AUDIO/VIDEO cable, connect
TV OUT on the projection TV to TV
AUDIO and VIDEO IN on the AV
receiver.

Using an S-LINK cable, connect S-LINK
on the VIDEO 1 IN panel on the
projection TV and S-LINK on MONITOR
OUT on the AV receiver.

Using an S-LINK cable, connect S-LINK
on the TV OUT panel on the projection
TV to S-LINK on TV IN on the AV
receiver.

Using AUDIO/VIDEO and S-LINK
cables, connect the Sony video equipment
to the AV receiver.

Use the Audio menu to set “Speaker” to
“Off” or “Center.” (see “Speaker” on
page 36)

Press CH (CHANNEL) +/– to activate
the S-Link function.

– 17 –

Insert two size AA (R6) batteries (supplied)
by matching the + and – on the batteries to
the diagram inside the remote control’s
battery compartment.

• Remove the batteries to avoid damage

from possible battery leakage whenever
you anticipate that the remote control
will not be used for an extended period.

• Handle the remote control with care.

Avoid dropping it, getting it wet, or
placing it in direct sunlight, near a heater
or where the humidity is high.

• Your remote control can be programmed to

operate most video equipment.
(see “Operating Video Equipment” on
page 55)

The supplied remote control has a joystick
which moves the on-screen selector in four
directions. In most cases, moving the joystick
up, down, left or right will cause the selector
to move in the selected direction.

In some cases, the selector may move in four
directions according to the function. Pressing
down on the center of the joystick (

) will

activate the selected item.

You may also move the joystick right to
activate a selected item. (There are some
exceptions to this option.)

.

When menu items present a slider ( 

 or

), move the joystick up, down, left or

right to adjust the setting.

Several menu windows will provide
prompts and instructions to assist you in
navigating through the different functions.

The AUTO SET UP feature will allow you to
set the on-screen language and set all
receivable channels.
The AUTO SET UP feature does not apply for
installations that use a cable box for all channel
selection.

Notes:
• Before you perform AUTO SET UP again,

make sure that the input from ANT (not
AUX) is selected by pressing ANT until
“AUX” does not appear next to the
channel number.

• Perform this function during the day,

with the antenna and/or cable properly
connected, to ensure that all available
channels will be broadcasting and
receivable.

• When you perform AUTO SET UP, all the

settings in the Video, and Audio menus
are reset to the factory settings.

Using the buttons on the front panel of the
projection TV:

Press POWER to turn on the projection
TV.
The AUTO SET UP screen appears.

Press CHANNEL +  to select English,
CHANNEL –  to select Español or
VOLUME +  to select Français.

The screen will change to reflect your
choice.

Press VOLUME –  to continue.

Press CHANNEL + to preset channels
automatically.

“Auto Program” appears and the
projection TV starts scanning and
presetting channels automatically. While
scanning, the received channel will be
displayed on the sub screen. When all the
receivable channels are stored, the lowest
numbered channel is displayed.

Press  [ SET UP ]  to exit.

First please connect
 the  antenna.

A u t o   S e t   U p   :

E s p a ñ o l   :

E n g l i s h   :

F r a n ç a i s   :

  [ V O L – ]

  [ C H – ]

  [ C H + ]

  [ V O L + ]

A u t o   P r o g r a m

Oprima  [ SET UP ]  para
salir.

Primero conecte la
antena.

  [ V O L – ]

  [ C H – ]

  [ C H + ]

  [ V O L + ]

A u t o   S e t   U p   :

E s p a ñ o l   :

E n g l i s h   :

F r a n ç a i s   :

N o   :

A u t o   P r o g r a m   ?

C o n t i n u e   t o

Y e s   :

  [ C H – ]

  [ C H + ]