DOWNLOAD Sony KDS-60R2000 Service Manual ↓ Size: 12.37 MB | Pages: 127 in PDF or view online for FREE

– 2 –

These servicing instructions are for use by qualified service per-
sonnel only.
To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you
are qualified to do so.

WARNING!!

AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BE-
CAUSE OF LIVE CHASSIS.
THE CHASSIS OF THIS RECElVER IS DIRECTLY CONNECTED
TO THE AC POWER LINE.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY SHADING AND MARK 

! ON THE

SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART NUM-
BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-
MENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARE CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS
MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITI-
CAL COMPONENTS ARE REPLACED OR IMPROPER OPERA-
TION IS SUSPECTED.

– 3 –

Power Requirements:

220–240 V AC, 50 Hz

Projection System:

3 SXRD Panel, 1 lens projection system

SXRD Panel:

Size 0.61 inch SXRD panel
Resolution 1920  108 0 pixels

Projection Lenses:

High performance, large-diameter hybrid lens F2.5

Lamp:

Ultra high pressure lamp, 120 W, XL-5100

Screen Size:

60 inches

Power Consumption:

230 W

Standby Power Consumption:

0.5 W

Dimensions (w

 × h × d):

Approx. 1,674 

× 1,009 × 514 mm

Weight:

Approx. 52 kg

Analog: B/G, I, D/K, M
Digital: DVB-T

Analog: PAL, SECAM, NTSC 3.58, PAL60/NTSC 4.43 

(only Video In)

Digital: MP@HL and MP@ML

75 ohm external terminal

Analog: B/G

VHF: E2 to E12 / UHF: E21 to E69 /
CATV: S01 to S03, S1 to S41
VHF: 0 to 12, 5A, 9A / UHF: 28 to 69 /
CATV: S01 to S03, S1 to S41(Australia only)
VHF: 1 to 11 / UHF: 21 to 69 /
CATV: S01 to S03, S1 to S44 (New Zealand only)

I

UHF: B21 to B69 / CATV: S01 to S03, S1 to S41

D/K

VHF: C1 to C12, R1 to R12 / 
UHF: C13 to C57, R21 to R60 /
CATV: S01 to S03, S1 to S41, Z1 to Z39

M

VHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84

Digital: VHF/UHF

1, 2

Supported formats: 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync
P

B

/C

B

: 0.7 Vp-p, 75 ohms

P

R

/C

R

: 0.7 Vp-p, 75 ohms

1

S video input (4-pin mini DIN)

1, 2, 3

Video input (phono jack)
1, 2, 3
Audio input (phono jacks)
500 mVrms
Impedance: 47 kilohms

HDMI IN 1, 2

Video: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM

32, 44.1 and 48 kHz, 16, 20 and 24 bits 

Analog audio (phono jacks):

 500 mVrms, Impedance 47 kilohms
(HDMI IN 2 only)

Video output (phono jack)

DIGITAL OUT (OPTICAL)

Audio output (phono jacks)

PC IN 

 RGB 

PC Input (D-sub 15-pin) (see page 45)
G: 0.7 Vp-p, 75 ohms, non Sync on Green
B: 0.7 Vp-p, 75 ohms
R: 0.7 Vp-p, 75 ohms
HD: 1-5 Vp-p
VD: 1-5 Vp-p

PC IN 

 

PC audio input (minijack)

i

H

Size AA batteries (R6 type) (2)
AC power cord (1)

eadphones jack

15 W + 15 W

Remote RM-GD001 (1)

• TV  stand SU-GW12
• Lamp XL-5100

Design and specifications are subject to change 
without notice.

– 4 –

• This TV’s PC input does not support Sync on Green or Composite Sync.
• The  PC  input signal displays on-screen in a smaller size than the actual TV screen size and does not support interlaced signals.
• For  the  best  picture quality, it is recommended to use the boldfaced signals in the above chart with a 60 Hz vertical frequency 

from a personal computer. In plug and play, signals with a 60 Hz vertical frequency will be selected automatically.

VGA

640

480

37.5

75

VESA

720

400

31.5

79

VGA-T

SVGA

800

600

46.9

75

VESA

XGA

1024

768

56.5

70

VESA

1024

768

60

75

VESA

WXGA

1280

768

60.3

75

VESA

SXGA

1280

1024

80

75

VESA

HDTV

1920

1080

67.5

60

EIA

– 5 –

Make sure that the TV is completely switched off before unplugging the AC power cord. Unplugging the AC power cord while the 
TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.

1

Å In  TV  mode: Selects the next (+) or previous 

(-) channel.

Å In  TV  menu: Moves through the options up 

(

)  or  down (

).

2

2

Å In  TV  mode:  Increases (+) or decreases (-) the 

volume.

Å In TV menu: Moves through the options right 

(

)  or  left (

).

3

Å In  TV  mode (page 20): Selects the input 

source from equipment connected to the TV 
jacks.

Å In  TV  menu: Selects the menu or option, and 

confirms the setting.

4

5

1

Flashes in green when the light source is 
preparing to turn on. Lights up in green when the 
TV is switched on.
Lights up in red when the TV is in standby mode. 
If the lamp cover or the lamp itself is not securely 
attached, the red indicator will continue to flash 
in intervals of three blinks at a time.

6

Lights up in orange when the timer is set 
(page 29).

7

Flashes in red when the lamp for the light source 
has burned out.

8

9

1

Switches the TV on or off.

Your TV uses a projection lamp as its light source. As with 
any lamp, it has lifespan and needs to be replaced when the 
lamp indicator flashes or the screen becomes darker.

• After switching on your TV, it may take a while (1 minute 

or less) before the picture appears.
When the projection lamp wears out, the screen goes dark.

• Replace the lamp with a new Sony XL-5100 replacement 

lamp (not supplied). How to replace the lamp, see page 42.

The light emitted from the lamp is quite bright when your TV 
is in use. To avoid eye discomfort or injury, do not look into 
the light housing when the power is on.