Sony KDS-60R2000 Service Manual ▷ View online
– 2-12 –
KDS-60R2000
RM-GD001
2-20. NOTES ON HARNESS ARRANGEMENTS
Core
Set core in a frame.
When you process, don’t apply to
a connector. Moreover, press down
a connector after processing.
a connector. Moreover, press down
a connector after processing.
– 2-13 –
KDS-60R2000
RM-GD001
Clamper
Slit
Leads from power supply block
Power supply block
Clamper
Clamper
Bend
Wire holder should
be lamp side.
be lamp side.
Press leads tightly
into the slit
into the slit
There is no leads to be caught.
Chassis assembly should be atached gradually with managing leads.
Chassis assembly should be atached gradually with managing leads.
The shield and leads from C board come out
from here.
* Be sure not to break the lead.
from here.
* Be sure not to break the lead.
Bottom assembly
– 2-14 –
KDS-60R2000
RM-GD001
Be sure to connect the same color of
the connectors and the same number
of the pins
the connectors and the same number
of the pins
– 3-1 –-
KDS-60R2000
RM-GD001
SECTION 3
ELECTRICAL ADJUSTMENTS
3-1.
ELECTRICAL ADJUSTMENT BY REMOTE
COMMANDER
COMMANDER
By using remote commander (RM-GA006), all circuit adjust-
ments can be made.
NOTE : Test Equipment Required.
1. Pattern Generator (with component outputs)
2. Oscilloscope
3. Digital multimeter
3-1-1. Method of Setting the Service Adjustment
Mode
1. Standby mode. (Power off)
2. DISPLAY
t 5 t VOL (+) t TV POWER
on the remote commander.
(Press each button within a second.)
The following service screen will appear.
Category Name
Mode
<Digital> Program
TVM Service Menu
SERVICE
XXX VERSION
XXX VERS
XXX VERS
XXX
: X.XX.XXX
<TV>
Program : X.XXX
<WE>
Program : X.XXX
<DE>
Program : X.XXX
Data
Data
: X.XXX
Boot
: X.XXX
Data
: X.XXX
Boot
: X.XXX
Data
: X.XXX
Boot
: X.XXX
Boot
: X.X.XX
Item Name
Category Name
Item Name
Sub Item Name
Item No.
Sub Item No.
PANEL
SERVICE
0 OP MODE
0 T1
0 T1
5
DIFF
1
50Hz
Data
<DISPLAY ENGINE>
3-1-2. Service Mode Adjustment
1. The SCREEN displays the item being adjusted.
2. Press “1” or “4” on the remote commander to select the
adjustment item.
3. Press “3” or “6” on the remote commander to change the data.
4. Press “2” or “5” on the remote commander to select the category.
Every time you press “2” (Category up), Service mode
changes in the order as shown below.
5. If you want to recover the latest values press “-” then
“[ENTER]” to read the memory.
6. Press “[MUTING]” then “[ENTER]” to write into memory.
7. Turn power off.
<Method of setting the shipping condition>
1. Service Adjustment mode.
1. Service Adjustment mode.
2. Press “8” then “[ENTER]”
3. Wait until appearing “ Initial Setup” display.
4. Disconnect AC plug and connect again to change factory re-
set condition completely.
3-1-3. Memory Write Confirmation Method
1. After adjustment, turn power off with the remote commander.
2. Turn power on and set to service mode.
3. Call the adjusted items again and confirm they were adjusted.
Key
TVM Service Menu
JUMP
WEM VERSION
JUMP
PANEL SERVICE
0 OPMODE
1 TG
1 TG
2
2 WB
2
3 CSC
2
4 HUE
2
5 TEST_PAT
:
:
:
:
34 LUM
2
0 OPMODE
:
:
Click on the first or last page to see other KDS-60R2000 service manuals if exist.