DOWNLOAD Sony KDL-46HX855 / KDL-55HX855 Service Manual ↓ Size: 2.39 MB | Pages: 53 in PDF or view online for FREE

KDL-46HX855/55HX855 vi

After correcting the original service problem, perform the following safety 

checks before releasing the set to the customer:

1.  Check the area of your repair for unsoldered or poorly soldered 

connections. Check the entire board surface for solder splashes 

and bridges.

2.  Check the interboard wiring to ensure that no wires are pinched or 

touching high-wattage resistors.

3.  Check that all control knobs, shields, covers, ground straps, and 

mounting hardware have been replaced. Be absolutely certain that 

you have replaced all the insulators.

4.  Look for unauthorized replacement parts, particularly transistors, 

that were installed during a previous repair. Point them out to the 

customer and recommend their replacement.

5.  Look for parts which, though functioning, show obvious signs of 

deterioration. Point them out to the customer and recommend their 

replacement.

6.  Check the line cords for cracks and abrasion. Recommend the 

replacement of any such line cord to the customer.

7.  Check the antenna terminals, metal trim, metallized knobs, screws, 

and all other exposed metal parts for AC leakage. Check leakage 

as described in “Leakage Test”.

The AC leakage from any exposed metal part to earth ground and from all 

exposed metal parts to any exposed metal part having a return to chassis, 

must not exceed 0.5 mA (500 microamperes). Leakage current can be 

measured by any one of three methods.

1.  A commercial leakage tester.  

Follow the manufacturers’ instructions provided with the tester.

2.  A battery-operated AC milliammeter. 

3.  Measuring the voltage drop across a resistor by means of a VOM 

or battery-operated AC voltmeter. The limit indication is 0.75 V, so 

analog meters must have an accurate low voltage scale. Nearly all 

battery-operated digital multimeters that have a 2 VAC range are 

suitable. (see Figure A)

Figure A. Use an AC voltmeter to check AC leakage.

The cover-plate retaining screw on most AC outlet boxes is at earth ground. 

Verify the AC outlet box retaining screw ground by connecting a 60W to 

100W incandescent (not a neon or fluorescent lamp) between the hot side of 

the receptacle and the retaining screw. Try both slots, if necessary, to locate 

the hot side on the line; the lamp should light at normal brilliance if the screw 

is at ground potential. (see Figure B)

Figure B. Checking for earth ground.

Trouble Light

AC Outlet Box

KDL-46HX855/55HX855 1

The AZ3G chassis is one of several designs for the 2012 model line of Sony 

Bravia® LCD televisions. This manual covers the following models:
 KDL-46HX855
 KDL-55HX855

The BRAVIA® HX85x series features a truly transcendent picture quality, 

each scene in everything you watch—HD movies, 3D, sports, even 

YouTube™ clips—is presented with unprecedented detail and astonishing 

color from Sony’s exclusive X-Reality™ PRO picture engine. Ultra-clear, 

realistic motion during slow scenic sweeps and fast action sports comes 

courtesy of Motionflow™ XR 960.

 

Pro-grade detail for discerning eyes: X-Reality™ PRO

 

Experience precise motion clarity with Motionflow™ XR 960

 

Frameless design with Corning’s Gorilla® Glass

 

Movies, music & apps with Sony Entertainment Network

1

 

Amazingly crisp, natural 3D effects in every 3D scene

2

 

Dynamic Edge LED backlight for amazing contrast & color

 

Stream HD entertainment wirelessly with built-in Wi-Fi®

1

 

PC and tablet content

3

 on your TV with Intelligent Connect

 

Make life-sized video calls with Skype®

1

 

Media Remote™ app to control your TV with a smartphone

4

 

Connect to the TV via Wi-Fi® without using a router

3

Sistema de televisão

Analógico: NTSC/PAL-M/PAL-N
Digital: SBTVD

Cobertura de canais

VHF: 2-13
UHF: 14-69
CATV (analógico): 1-135

Sistema do painel

Painel LCD (tela de cristal líquido) 

Potência de saída dos alto-
falantes (

RMS

)

10 W + 10 W (8 ohms, 1 kHz, 10% THD*

1

,127V) + 10 W (8 ohms, 100 Hz, 10% THD*

1

,127V)

CABLE/ANTENNA

Terminal de antena externa de 75 ohms para entradas RF

VIDEO IN 1

Entrada de vídeo / áudio (tomadas RCA)

COMPONENT IN

VIDEO IN 2

YP

B

P

R

 (vídeo componente):1080p (50, 60 Hz), 1080i (50, 60 Hz), 720p (50, 60 Hz), 576p, 576i,  480p, 480i

Entrada de áudio (tomadas RCA)
Entrada de vídeo (plugue RCA comum com entrada Y)

HDMI IN 1/2/3/4

Vídeo (2D): 1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p, 576p, 576i, 

480p, 480i, Formatos PC

Vídeo (3D):

Frame Packing1

080p (30 Hz), 1080/24p, 1080i (50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p

Lado a lado (Side-by-Side)

1080p (50, 60 Hz), 1080/24p, 1080i (50, 60 Hz), 720p (30, 50, 60 Hz)

Cima baixo (Over-Under)

1080p (30, 50, 60 Hz), 1080/24p, 1080i (50, 60 Hz), 720p (50, 60 Hz)

Áudio: Dois canais PCM lineares: 32, 44.1 e 48 kHz, 16, 20 e 24 bits, Dolby Digital
Entrada de áudio analógico (minitomada estéreo) (somente HDMI IN 2, comum com PC IN)
ARC (Audio Return Channel, Canal de Retorno de Áudio) (somente HDMI IN 1)

AUDIO OUT/Fones de 

ouvido

Minitomada estéreo

DIGITAL AUDIO OUT 

(OPTICAL)

Tomada digital óptica (PCM linear de dois canais, Dolby Digital)

Pedestal Integrado das caixas 
acústicas

Saída do áudio para o pedestal da TV 

PC IN
PC/HDMI 2 AUDIO IN

RGB analógico (Mini D-sub de 15 pinos)
Entrada de áudio (minitomada estéreo) (comum com HDMI IN 2)

LAN

Conector 10BASE-T/100BASE-TX (A velocidade da conexão pode ser diferente dependendo do 
ambiente de rede. A taxa e a qualidade de comunicação de 10BASE-T/100BASE-TX não estão 
garantidas nesta TV.)

USB/DLNA

Consulte o i-Manual para obter informações sobre o formato suportado.

*1 Distorção Harmônica Total.

1.  Broadband speed of at least 2.5 Mbps recommended (10 Mbps for HD). Content subject to 

change and may require fees. Skype requires CMU-BR100 camera sold separately. Subject 

to Skype’s terms and conditions. 

2.  Requires 3D content, 3D player, HDMI® cable (at least 10.2 Gbps) and 3D active glasses 

sold separately. 

3.  Streaming content, copy-protected content and certain formats are not supported. 
4.  Requires devices connected to the same wireless home network.

KDL-46HX855/55HX855 2

*2 Os valores de tamanhos de tela, dimensões e pesos são aproximados.

• A disponibilidade dos acessórios opcionais depende do país/região/modelo de TV/estoque.

• Projeto e especificações técnicas sujeitos a alterações sem prévio aviso.

Acessórios opcionais

Suporte da TV: SU-B553S (KDL-55HX855)

SU-B463S (KDL-46HX855)

Óculos 3D:

 TDG-BR750/TDG-BR250/TDG-BR200/TDG-BR100/TDG-BR50

Unidade de câmera e microfone: CMU-BR100
Adaptador USB LAN Wireless: UWA-BR100

Temperatura de operação
Umidade de operação

10 % – 80 % RH (sem condensação)

Requisitos de alimentação

Consumo de 
energia

em uso

150 W

120 W

em standby

Menos que 0,2 W com 127 V CA e menos que 0,3 W com 220 V CA

Tamanho da tela*

2

(cm)

(polegadas

medidas diagonalmente)

Aprox. 138,8
54,6 polegadas
(classe 55)

Aprox. 116,8
46 polegadas

Resolução do monitor 

1.920 pontos (horizontal) × 1.080 linhas (vertical)

Dimensões*

2

com pedestal 
(mm)

1.274 × 808 × 341

1.077 × 697 × 268

sem pedestal

 

(mm)

1.274 × 750 × 35

1.077 × 640 × 35

padrão de furo 
para montagem 
na parede (mm)

300 × 300

tamanho do 
parafuso para 
montagem na 
parede

(mm)

 

 

 

              M6 (8-12 mm)

Peso*

2

com pedestal 

(kg)

26,2

20,3

sem pedestal 

(kg)

21,7

16,6

Acessórios fornecidos

 Verificando os acessórios.

 

110-220 V CA, 60 Hz 

0 ºC – 40 ºC

*

1

Consulte o nome do modelo impresso no controle 

remoto.

*

2

Necessária montagem do pedestal. Consulte o folheto 

que acompanha o pedestal para montar o pedestal.

KDL-46HX855/55HX855 3

The primary circuits in the AZ3G chassis consist of a Main Board (BAPS Board), Power Supply Board (G6 Board for the 46” models, and G7 Board for the 55” 

models), the IR Board (HL Board), the 3D IR Emitter (HEM3 Board), the Wireless LAN Card, the Switch Unit, and the LCD Panel assembly which includes the 

TCON Board.
NOTE: For connector part number information, refer to 

“Connectors” on page 24

. For Wire Dressing information, refer to 

“Wire Dressing” on page 26

.

SWITCH

UNIT

HL

HEM3

TCON

G6

BAPS

WIRELESS

LAN CARD

SWITCH

UNIT

HL

HEM3

TCON

G7

BAPS

WIRELESS

LAN CARD