DOWNLOAD Sony KDL-26S3000 / KDL-32S3000 / KDL-40S3000 / KDL-46S3000 Service Manual ↓ Size: 32.65 MB | Pages: 127 in PDF or view online for FREE

Model
KDL-26S3000 KDL-32S3000 KDL-40S3000 KDL-46S3000
Pages
127
Size
32.65 MB
Type
PDF
Document
Service Manual
Brand
Device
TV
File
kdl-26s3000-kdl-32s3000-kdl-40s3000-kdl-46s3000.pdf
Date
PREV: Sony KV-21FA350 (serv.man2) Service Manual

Sony KDL-26S3000 / KDL-32S3000 / KDL-40S3000 / KDL-46S3000 Service Manual ▷ View online

 45 
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
KDL-32S3000 ONLY
Install/Wire Dress Harnesses as shown.
CAUTION: Make sure INVERTER CONN.
is Fully LOCKED!!
OPERATION  PROCESS
1
2
CAUTION:
 Make Sure Inverter 
Connector is Fully LOCKED!
G1H-
Bd
NOTE: NEW G-Bracket Change!
Inverter wire is NOT dressed in 1st clip.
Inverter wires are dressed in cut-out on
side of the G-Bracket and the 2nd clip on right.
13P harness is NOT dressed in any of the
clips above PWB!
G1H BOARD
 46 
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
KDL-32S3000 ONLY
1. Wire Dress Speaker Cables as shown.
2. BOTH R/L cables are dressed in FGC-3
conductive clip.
3. Apply LCD TAPE to BOTH H4-Bd AND Right
Speaker Wires.
TORQUE: 6kg.cm (+-1.0kg.cm)
OPERATION  PROCESS
TORQUE SPECIFICATION
1
2
3
Apply Sheet Core C  to BOTH H4/H3 AND Right Speaker Wires.
Align edge of tape with White Plastic Peg On Panel.
SPEAKER HARNESS
 47 
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
KDL-32S3000 ONLY
Dress LEFT speaker harness as shown
OPERATION  PROCESS
1
Side Clamp Installed by SBC PLANT!
2
PUSH SIDE CLAMP THIS DIRECTION TO LOCK!!
LEFT SPEAKER HARNESS
 48 
KDL-26S3000/32S3000/40S3000/46S3000
KDL-26S3000/32S3000/40S3000/46S3000
KDL-32S3000 ONLY
1. Apply Sheet Core A to Panel in location
where U1 bracket is to be installed
(Use edges of panel as guide)
2. Make sure DTT Shield has Sheet Core C
installed as per diagram.
3. Wire Dress 20P Harness as shown.
Put attention on DIRECTION of wires from
BU-Bd inside side clamp on U1 Bracket.
OPERATION  PROCESS
2
1
Align side edge of panel
Align with bottom of panel
Sheet Core C (Installed by Vendor)
3
3/4/2007 LATE CHANGE:
ADD 3x12mm SCREW Here.
DO NOT Cross wires over 
Optical Output Connector
(Pinch Point when Rr. Cover is
installed).
㩸
㩸
U1 BOARD
Page of 127
Display

Click on the first or last page to see other KDL-26S3000 / KDL-32S3000 / KDL-40S3000 / KDL-46S3000 service manuals if exist.

RANDOM: