Sony KDL-22PX300 / KDL-32EX403 / KDL-32EX40B / KDL-32EX43B / KDL-32EX500 / KDL-32EX501 / KDL-32EX503 / KDL-32EX504 / KDL-32EX505 / KDL-32EX508 / KDL-32EX603 / KDL-32EX605 / KDL-32EX700 / KDL-32EX701 / KDL-32EX703 / KDL-32EX705 / KDL-32EX706 / KDL-32EX707 / KDL Service Manual ▷ View online
AZ1 VERSIONUP PROCEDURE(EU)
25
When the
green LED
and
amber LED
blink, insert USB into the set, and after about 30 seconds the set is rebooted. Then, the
Standby
LED
lights and the
Timer LED
blinks. After about 3 minutes, the set is rebooted and is turned on. After a while, a completion message is
displayed.
If USB is left inserted, a message like above is
displayed. If so, remove USB.
displayed. If so, remove USB.
Upgrading...
Upgrade is complete.
No image or message may be displayed.
2-5. Screens Displayed while Upgrading the Version
SERVICE PANEL
SERVICE PANEL
AZ1 VERSIONUP PROCEDURE(EU)
26
1. Use the remote commander to switch the TV into Standby mode.
2. Press keys “DISPLAY -> 5ch -> Vol+ -> POWER ON” on the remote commander.
3. Confirm the Software Version from the Service menu.
2. Press keys “DISPLAY -> 5ch -> Vol+ -> POWER ON” on the remote commander.
3. Confirm the Software Version from the Service menu.
Digital Service menu
DIGITAL SERVICE
001 OP
000 VERS ‐‐‐
000 VERS ‐‐‐
<MAIN> <SUB>
DM1.301J00AA SM1.010W00AA
M2.105C
DM1.301J00AA SM1.010W00AA
M2.105C
SB1.000W00AA
DD1.016J00AA SD1.010W00AA
(DM1.301J00AA) RF01.05
WP00.521J00AA ID1C117081
ID1C117081 LTY320AB01
PID04020000
WF:2.0.0.99 <BEM>
WF:0B BM1.012W00LU
Camera FW BB1.000W00LU
Camera FW BD1.011J46LUX
(DM1.301J00AA) RF01.05
WP00.521J00AA ID1C117081
ID1C117081 LTY320AB01
PID04020000
WF:2.0.0.99 <BEM>
WF:0B BM1.012W00LU
Camera FW BB1.000W00LU
Camera FW BD1.011J46LUX
‐‐‐.‐‐‐‐‐‐‐‐‐
Software
Version
Remote Commander
1
3
4
2
2-6. Confirming the Software Version from the Service Menu
SERVICE PANEL
SERVICE PANEL
AZ1 VERSIONUP PROCEDURE(EU)
27
1. Use the remote commander to switch the TV into Standby mode.
2. Press keys “DISPLAY -> 5ch -> Vol- -> POWER ON” on the remote commander.
3. Press keys “7ch -> 10ch/0” on the remote commander.
4. Confirm that “00000” is displayed in Panel Operation Time enclosed in a red box.
1
Remote Commander
2
Service Menu
SELF CHECH <1> NEXT PAGE‐>
000 RGB_SEN ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
002 MAIN_POWE ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
003 DC_ALERT ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
003 AUD_PROT ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
003 DTT_WDT ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
004 BALANCER ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
005 HFR_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
005 TCON_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
005 P_ID_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
006 BACKLITE ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
007 TEMP_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
007 FAN_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
010 RESERVED ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
011 RESERVED ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
002 MAIN_POWE ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
003 DC_ALERT ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
003 AUD_PROT ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
003 DTT_WDT ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
004 BALANCER ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
005 HFR_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
005 TCON_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
005 P_ID_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
006 BACKLITE ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
007 TEMP_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
007 FAN_ERR ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
010 RESERVED ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
011 RESERVED ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ ‐‐‐‐‐‐‐‐‐‐ 00
12345‐67891‐23456
Panel Operation Time
2-7. Resetting the Panel Operation Time from the Service Menu
SERVICE PANEL
SERVICE PANEL
AZ1 VERSIONUP PROCEDURE(EU)
28
3-1. Steps After Replacing the T-con Board
Note: Before operation, disconnect all cables connected to the set.
SEC.3 T
SEC.3 T
-
-
CON BOARD
CON BOARD
1. Replace the T-con board.
2. Specify the following from the Service menu:
a. Specify PRETEND_ID of DL in PEM.
3. By using the USB memory, upgrade Software.
4. Re-specify the following from the Service menu:
a. Specify DATA_TRANS_SET of TCON_CHANGED in PEM.
b. Specify DATA_TRANS_EXE of TCON_CHANGED in PEM.
c. Check whether or not DATA_TRANSFER succeeded.
5. After turning off and on the power, confirm the Software Version from the Service menu.
6. Conclude the operation.
Click on the first or last page to see other KDL-22PX300 / KDL-32EX403 / KDL-32EX40B / KDL-32EX43B / KDL-32EX500 / KDL-32EX501 / KDL-32EX503 / KDL-32EX504 / KDL-32EX505 / KDL-32EX508 / KDL-32EX603 / KDL-32EX605 / KDL-32EX700 / KDL-32EX701 / KDL-32EX703 / KDL-32EX705 / KDL-32EX706 / KDL-32EX707 / KDL service manuals if exist.