Sony KDF-46E3000 / KDF-50E3000 Service Manual ▷ View online
KDF-46E3000/50E3000
KDF-46E3000/50E3000
29
CHASSIS ASSEMBLY (CONTINUED)
Dress 40P Connector to WIRE PIN on [G]
191003507
CONN ASSY, 40P
191003660
CONN ASSY, 9P
ZMR 500
KDF-46E3000/50E3000
KDF-46E3000/50E3000
30
HCE BLOCK ASSEMBLY
191003665
HARNESS ASSY
HARNESS ASSY MUST BE INSTALLED BEFORE
PUTTING INTO HC BRACKET
Ensure connector is routed so that it does not go
above red line shown above.
Dress to wire holder installed on HCE Board.
Route HARNESS ASSY THROUGH
OPENING IN THE REAR COVER
Dress to wire holder
on FAN BRACKET
Install on [U] board as shown. Connector
should be above 3P Connector
Dress to Wire Holder on Terminal Bracket.
46" Models must be looped to take up excess slack
50" Models DO NOT need to be looped
46" Models must be looped to take up excess slack
50" Models DO NOT need to be looped
Correct Routing
of HC wire
KDF-46E3000/50E3000
KDF-46E3000/50E3000
31
Dress Speaker Wire to clips on Separator before
installing. Black tape should be inside of clips.
installing. Black tape should be inside of clips.
191003661
CONN ASSY, 9P ZHR 860
Route 9P and Speaker
Wire as shown.
Wire as shown.
9P [HBE] should be
under speaker wire
Dress Speaker Wire and 9P [HBE] connector to wire
holders on the FRONT STAY
Route 9P and Speaker
Wire as shown.
DO NOT install to wire holder
this should be done later.
SEPARATOR BLOCK ASSEMBLY
KDF-46E3000/50E3000
KDF-46E3000/50E3000
32
2-1. USING THE REMOTE COMMANDER
FOR ELECTRICAL ADJUSTMENTS
To adjust various set features, use the Remote Commander to put the
set into service mode to display the service menus and categories.
set into service mode to display the service menus and categories.
Equipment Needed:
Pattern Generator (with component outputs)
Oscilloscope
Digital multimeter
2-2. ACCESSING SERVICE ADJUSTMENT
MODE
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a
second of each other:
DISPLAY
Channel
5
Volume
+
POWER .
Displays
Service Menus
DISPLAY
VOLUME (+)
POWER
JUMP
RM-YD016
Onscreen cursor
and select button
and select button
5
The fi rst service menu (TV) displays.
SECTION 2: CIRCUIT ADJUSTMENTS
2-3. VIEWING THE SERVICE MENUS
Use the Remote Commander to view the BE and Digital service menus
options.
options.
1. To display the Service Menu that contains the Category you want to
adjust, press JUMP on the Remote Commander.
(For a complete list of the service Categories refer to Service Menus)
(For a complete list of the service Categories refer to Service Menus)
Press JUMP
SOFTWARE VERSION
VIDEO1 WIDE
VIDEO1 WIDE
ZOOM
SERVICE
TVM:
ATSC:
BE:
NVM:
SWDL
F A:
CBA:
P1. 000U. - BOOT: 0.005
HO7-01.01 0035
2.710 BOOT:A.103
AO-1.001:OK AC-1.000:OK
0.000
00000000 00000000
00000000 00000000
HO7-01.01 0035
2.710 BOOT:A.103
AO-1.001:OK AC-1.000:OK
0.000
00000000 00000000
00000000 00000000
480I
Press JUMP
QM 0
0
SERVICE
INFO
DTV
WEM VERSION
Main
Main
WM2. 710U00GA
WM1. 103W00AA
Boot
Diff
WM2. 710U00GA
DL 0. 00 Gra 0216
SelfCheck 00 00 00 00
DEM VERSION
PMO. 000 PBO. 000
NVM: PDO. 000
NVM: PDO. 000
WC2. 712U00GAa
Boot
Press JUMP
Press JUMP
PANEL
DIFF
1
60HZ
OPMODE
ONO
ONO
SERVICE
0
0
0
Sample Service Menu
Click on the first or last page to see other KDF-46E3000 / KDF-50E3000 service manuals if exist.