Sony KDF-46E3000 / KDF-50E3000 Service Manual ▷ View online
KDF-46E3000/50E3000
KDF-46E3000/50E3000
25
OPTICAL BLOCK ASSEMBLY
191003656
Harness Assy
Dress 191003656 to (3) Wire
Holders on CE Block
183411811 LVDS
Connector Assy
Dress to (3) Wire
Holders on CE Block
Dress to (2) wire
holders as shown
191003666
CONN ASSY, 8P 200
Place wire into channel in Optical Blk.
Line up edge with tape on 8P Connector
8P connector should be
below LVDS
Secure 8P Connector with 20 X 40 Himelon Tape 265206401
KDF-46E3000/50E3000
KDF-46E3000/50E3000
26
191003664
CONN ASSY, 5P SMR 60
191002827
CONNECTOR ASSY 2P
Route Duct Blk Fan
toward [T] as shown
191003517
CONN ASSY 3P, SMR
[T] Board
Use Caution when installing Duct block that 5P
and 2P Connectors are not pinched
191003658
CONN ASSY, 7P 455
191003659
CONN ASSY, 3P VH1120
After installing 7P
Conn assy Secure to
Ballast Bracket with
20 X 40 Himelon
Tape 265206401 as
Shown. This is to
avoid it from hitting
Capacitor on ballast
Conn assy Secure to
Ballast Bracket with
20 X 40 Himelon
Tape 265206401 as
Shown. This is to
avoid it from hitting
Capacitor on ballast
191003658
CONN ASSY, 7P 455
Connector should be
routed outside of post
Secure Both Connectors to hooks on Ballast bracket and
ensure Ferrite core is placed in rib as shown
Hooks
Rib
After Installing Ballast Bracket route wires through
openings in Duct Block as shown.
5P Connector should be
under 2P Connector
DUCT BLOCK ASSEMBLY
KDF-46E3000/50E3000
KDF-46E3000/50E3000
27
Install Ballast Power in Clip on bottom of Duct Block.
Wire should be routed with RED tape in this position
Install Ballast Power to Clip and secure with Himelon
Tape 20 X 40. Tape should be centered between clips
Himelon Tape
Clips
Route 2P Thermal fuse
to clip and wire holder.
Route 3P Fan and 3P
[S] connector to clip on
top of Duct Blk.
191003657
HARNESS ASSY
Route HARNESS ASSY
191003657 to Clip on
Duct Block.
191003657
HARNESS ASSY
Connect 9P Ballast Control Connector and
2P Thermal Fuse Connector from
HARNESS ASSY 191003657
Secure Harness Assy, 2P Thermal fuse,4P [HAE], and 9P
Ballast control connector to wire holders as shown.
NOTE: Ensure 9P Connector is routed as shown
Wire Holders
Route 4P [HAE]
Connector through
Opening in Rear Cover
DUCT BLOCK ASSEMBLY (CONTINUED)
KDF-46E3000/50E3000
KDF-46E3000/50E3000
28
After installing Fan Secure wire with 20 X
40 Himelon Tape as shown.
40 Himelon Tape as shown.
191003507
Lighting ground should be behind AC cord. UL Tube should be
located on [G] board side of connection as shown below
located on [G] board side of connection as shown below
Before Installing [G] Board it may be necessar
bend tab slightly in order to properly install [G] b
191003511
WIRE ASSY, FASTON TERMINAL
Dress 3P Chassis Fan Connector to WIRE PIN on [G] as shown
Dress 4P Speaker
Connector to (2) Clips
on Main Bracket
191003667
CONN ASSY, 4P
SPEAKER SMR
191003508
CONN ASSY, 3P VH 130
CHASSIS ASSEMBLY
Click on the first or last page to see other KDF-46E3000 / KDF-50E3000 service manuals if exist.