Sony KDF-46E2000 / KDF-46E2010 / KDF-50E2000 / KDF-50E2010 / KDF-55E2000 / KDF-55E2010 Service Manual ▷ View online
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
45
When Pulling the damper through
the fan be careful not to use
excessive force which may break the
damper in this area
the fan be careful not to use
excessive force which may break the
damper in this area
269304701
GASKET(5 X 10 X 30)
DAMPER AND GASKET CAUTION POINTS
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
46
G-Board Wire Pin Holders
Instructions. There are (3)
wire pin Holders on the [G]
board. See below to see which
wires are dressed to each wire
pin holder
Instructions. There are (3)
wire pin Holders on the [G]
board. See below to see which
wires are dressed to each wire
pin holder
1. LVDS and 8P CN6009[G]
2. LVDS, 8P CN6009, and
7P CN3004[B]
7P CN3004[B]
3. LVDS and 7P CN3004[B]
1
2
3
When Dressing 1-910-024-29
and Duct Block Fan to wire
Holder ensure the wires are
not positioned above
capacitors on [G].
and Duct Block Fan to wire
Holder ensure the wires are
not positioned above
capacitors on [G].
This is to avoid the connector
wires from touching the rear
cover.
wires from touching the rear
cover.
Install Purse Lock
404928101 PURSE LOCK (DIA.11)
404928101 PURSE LOCK (DIA.11)
Purselock should hold the
following:
following:
32P Conn Assy [G] to [B]
3P Conn Assy [G] to [K]
3P Conn Assy [G] to ANT SWT
3P Conn Assy [G] to B-Blk FAN
3P Conn Assy [G] to [K]
3P Conn Assy [G] to ANT SWT
3P Conn Assy [G] to B-Blk FAN
G BOARD WIRE DRESSING CAUTION POINTS
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
47
Dress Positive Tab of Speaker
wire around speaker bracket
and then Himelon Tape should
be installed to secure the wire
as shown.
Wire Should be pulled so that
there is no excess wire.
THIS IS VERY IMPORTANT TO
AVOID NOISE DUE TO
SPEAKER VIBRATION
SPEAKER VIBRATION
Tape should wrap around
bracket as shown to the right
and securely hold the speaker
wire so that it does not move
once the tape is applied.
bracket as shown to the right
and securely hold the speaker
wire so that it does not move
once the tape is applied.
RIGHT SPEAKER WIRE DRESSING CAUTION POINTS
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
48
Apply Himelon tape to speaker
wire as shown to the left.
wire as shown to the left.
Speaker wire must be placed
inside Grooved slot in speaker
and then secured with Himelon
Tape.
inside Grooved slot in speaker
and then secured with Himelon
Tape.
Before applying tape ensure as
much slack is taken out of the
wire by pulling it towards the
negative terminal.
much slack is taken out of the
wire by pulling it towards the
negative terminal.
Wire Holder is installed on
speaker bracket as shown.
speaker bracket as shown.
Remove as much slack out of
wire before dressing it to the
wire holder.
wire before dressing it to the
wire holder.
ONLY FOR 50" MODELS
Pull wire in direction of arrow to
take out slack
265206401 TAPE,
HIMELON (20X40)
After dressing to wire holder
dress wire through speaker
bracket as shown to the left.
dress wire through speaker
bracket as shown to the left.
LEFT SPEAKER WIRE DRESSING CAUTION POINTS
Click on the first or last page to see other KDF-46E2000 / KDF-46E2010 / KDF-50E2000 / KDF-50E2010 / KDF-55E2000 / KDF-55E2010 service manuals if exist.