Sony KDF-46E2000 / KDF-46E2010 / KDF-50E2000 / KDF-50E2010 / KDF-55E2000 / KDF-55E2010 Service Manual ▷ View online
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
29
G-Board Wire Pin Holders Instructions. There are (3)
wire pin Holders on the [G] board. See below to see
which wires are dressed to each wire pin holder
wire pin Holders on the [G] board. See below to see
which wires are dressed to each wire pin holder
1. LVDS and 8P CN6009[G]
2. LVDS, 8P CN6009, and 7P CN3004[B]
3. LVDS and 7P CN3004[B]
Ensure wires are dressed to the side of the G Board
as shown.
as shown.
3
1
2
G BOARD WIRE DRESSING
Install Purse Lock
404928101 PURSE LOCK (DIA.11)
404928101 PURSE LOCK (DIA.11)
Purse lock should hold the following:
32P Conn Assy [G] to [B]
3P Conn Assy [G] to [K]
3P Conn Assy [G] to ANT SWT
3P Conn Assy [G] to B-Blk FAN
3P Conn Assy [G] to [K]
3P Conn Assy [G] to ANT SWT
3P Conn Assy [G] to B-Blk FAN
After installing Purse Lock ensure “open” end is
facing towards the front of the set.
facing towards the front of the set.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
30
OPTICAL BLOCK ASSEMBLY WIRE DRESSING
ROUTE IRS CONNECTOR AS SHOWN
APPLY HIMELONE TAPE AS SHOWN ABOVE
AND DRESS IRIS CONNECTOR ASSY
TO WIRE HOLDER AS SHOWN BELOW
AND DRESS IRIS CONNECTOR ASSY
TO WIRE HOLDER AS SHOWN BELOW
APPLY HIMELONE TAPE TO SECURE IRIS CON-
NECTOR AS SHOWN ABOVE.
APPLY TAPE SO THAT THE CONNECTOR ASSEM-
BLY WILL NOT BE IN SHADED AREA ABOVE.
NECTOR AS SHOWN ABOVE.
APPLY TAPE SO THAT THE CONNECTOR ASSEM-
BLY WILL NOT BE IN SHADED AREA ABOVE.
IF CONNECTOR ASSEMBLY IS IN THE SHADED
ARER IT WILL GET PINCHED BETWEEN THE
OPTICAL BLOCK ASSEMBLY AND THE BOTTOM
BLOCK ASSEMBLY WHEN INSTALLED.
ARER IT WILL GET PINCHED BETWEEN THE
OPTICAL BLOCK ASSEMBLY AND THE BOTTOM
BLOCK ASSEMBLY WHEN INSTALLED.
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
31
x Secure Ring Terminal of 1-910-016-90 to G-Block as shown above.
x Install Faston Terminal to Antenna Switch.
Note: Orientation of ring terminal should be towards the top of the set.
1-910-016-90
OPTICAL BLOCK ASSEMBLY LIGHTNING GROUND POSITION
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
KDF-46E2000/46E2010/50E2000/50E2010/55E2000/55E2010
32
For
55
”,
MUST use 2 screws
on each side
(total 4 screws)
to secure Speaker Grill to
Screen Frame.
Screen Frame.
For 50” and 46” use
only 1 screws each
side (total 2 screws)
only 1 screws each
side (total 2 screws)
SPEAKER GRILL WIRE DRESSING
Click on the first or last page to see other KDF-46E2000 / KDF-46E2010 / KDF-50E2000 / KDF-50E2010 / KDF-55E2000 / KDF-55E2010 service manuals if exist.