Sony KDF-42E2000 Service Manual ▷ View online
KDF-42E2000
KDF-42E2000
26
Install Conn Assy
1-910-024-21 to "FAN1"
Optical Block Fan.
Dress 15P CN9000 [C]
LVDS Connector and Fan
Connector to Purse Lock
on [C] Shield
Route Optical Block Fan
to Wire Holder to avoid
being “Pinched” when [G]
Shield is installed
C BLOCK WIRE DRESSING
KDF-42E2000
KDF-42E2000
27
Dress [B] Block Fan and [K] Board Connector Assy to Purse
Lock on [B] Block as shown above.
Lock on [B] Block as shown above.
CHASSIS WIRE DRESSING
Dress the following
Connector Assys to
Purse Lock on Duct Block
Assy :
Connector Assys to
Purse Lock on Duct Block
Assy :
1. CN150 [T1]
2. X1 (Ballast)
3. X2 (Ballast)
2. X1 (Ballast)
3. X2 (Ballast)
Note:
Duct Block Fan is not
installed to Purse Lock
Duct Block Fan is not
installed to Purse Lock
Dress the following
Connector Assys to Wire
Holder on Bottom Block:
Connector Assys to Wire
Holder on Bottom Block:
1. 1-910-024-29
2. X1 (Ballast)
3. X2 (Ballast)
4. Duct Block Assy Fan
5. Optical Block Fan
2. X1 (Ballast)
3. X2 (Ballast)
4. Duct Block Assy Fan
5. Optical Block Fan
Route Lamp Fan
“inside” of 1-910-024-29
and Inside of X2 (Ballast
Power)
“inside” of 1-910-024-29
and Inside of X2 (Ballast
Power)
DUCT BLOCK ASSEMBLY WIRE DRESSING
KDF-42E2000
KDF-42E2000
28
G-Board Wire Pin Holders Instructions. There are (3)
wire pin Holders on the [G] board. See below to see
which wires are dressed to each wire pin holder
wire pin Holders on the [G] board. See below to see
which wires are dressed to each wire pin holder
1. LVDS and 8P CN6009[G]
2. LVDS, 8P CN6009, and 7P CN3004[B]
3. LVDS and 7P CN3004[B]
Ensure wires are dressed to the side of the G Board
as shown.
as shown.
3
1
2
G BOARD WIRE DRESSING
Install Purse Lock
404928101 PURSE LOCK (DIA.11)
404928101 PURSE LOCK (DIA.11)
Purse lock should hold the following:
32P Conn Assy [G] to [B]
3P Conn Assy [G] to [K]
3P Conn Assy [G] to ANT SWT
3P Conn Assy [G] to B-Blk FAN
3P Conn Assy [G] to [K]
3P Conn Assy [G] to ANT SWT
3P Conn Assy [G] to B-Blk FAN
After installing Purse Lock ensure “open” end is
facing towards the front of the set.
facing towards the front of the set.
KDF-42E2000
KDF-42E2000
29
OPTICAL BLOCK ASSEMBLY WIRE DRESSING
ROUTE IRS CONNECTOR AS SHOWN
APPLY HIMELONE TAPE AS SHOWN ABOVE
AND DRESS IRIS CONNECTOR ASSY
TO WIRE HOLDER AS SHOWN BELOW
AND DRESS IRIS CONNECTOR ASSY
TO WIRE HOLDER AS SHOWN BELOW
APPLY HIMELONE TAPE TO SECURE IRIS CON-
NECTOR AS SHOWN ABOVE.
APPLY TAPE SO THAT THE CONNECTOR ASSEM-
BLY WILL NOT BE IN SHADED AREA ABOVE.
NECTOR AS SHOWN ABOVE.
APPLY TAPE SO THAT THE CONNECTOR ASSEM-
BLY WILL NOT BE IN SHADED AREA ABOVE.
IF CONNECTOR ASSEMBLY IS IN THE SHADED
ARER IT WILL GET PINCHED BETWEEN THE
OPTICAL BLOCK ASSEMBLY AND THE BOTTOM
BLOCK ASSEMBLY WHEN INSTALLED.
ARER IT WILL GET PINCHED BETWEEN THE
OPTICAL BLOCK ASSEMBLY AND THE BOTTOM
BLOCK ASSEMBLY WHEN INSTALLED.
Click on the first or last page to see other KDF-42E2000 service manuals if exist.