Sony RM-PJVW60 / VPL-VW60 Service Manual ▷ View online
1-5
VPL-VW60
1-3-3. HA Board and NR Board
!- Screw
(+PSW 3
(+PSW 3
x 8)
![ NR board
!= NR bracket
4 Ground plate
5 Four claws
6 Two dowels
3 Two screws
(+PSW 3
(+PSW 3
x 8)
9 HA board
8 Control button (A)
7 Joystick button
0 Screw
(+BVTP 3
(+BVTP 3
x 12)
HA board
Control button (A)
1 Two claws
2 Two dowels
HA board
Ground plate
Control button (A)
1-3-4. Front Panel Assembly
NF board
CN40
CN40
HB board
CN80
CN80
9 Lens cap
0 Remove the lens ring assembly
in the direction of the arrow.
in the direction of the arrow.
!- Front panel assembly
6 HB holder
7 Screw
(+PSW 3
(+PSW 3
x 8)
5 Screw
(+PSW 3
(+PSW 3
x 8)
8 NF board
4 HB board
3 Screw
(+PSW 3
(+PSW 3
x 8)
2 Two screws
(+BVTP 3
(+BVTP 3
x 12)
1 Two connectors
1-6
VPL-VW60
1-3-5. Optics Block
Press and
disconnect
the connector.
disconnect
the connector.
C board
CN1000
CN1000
Flat connector assembly
Wire holder
(M3)
(M3)
GA board
GB board
C board
3 Disconnect the connectors
from each board.
from each board.
CN303
CN701
CN1000
CN302
CN800
CN1003
CN1003
CN1002
Fan connector
Flat connector
assembly B
assembly B
Front Side
of Unit
of Unit
F holder
GA board
C board
GB board
1 Harnesses
2
F holder
Wire holder (M3)
6 Two screws
(+PSW 3
(+PSW 3
x 8)
7 House cover
9 Fuse connector
assembly
assembly
8 Lamp power supply
connector assembly
connector assembly
4 Screw
(+PSW 3
(+PSW 3
x 8)
5 Lamp fan duct
0 Four screws
(+BVTP 4
(+BVTP 4
x 16)
!= Optics block
!- Screw
(+PSW 3
(+PSW 3
x 8)
Be careful not to break each
flat connector assembly.
flat connector assembly.
G sheet
GA shield
Flat connector assembly A
Plastic tape
(UL tape, length ; 40mm)
(UL tape, length ; 40mm)
Note:
Keep the flat connector assembly
toward the GA board and place
the plastic tape (UL tape) on it, in
order to hold the flat connector
assembly tight on GA shield.
Keep the flat connector assembly
toward the GA board and place
the plastic tape (UL tape) on it, in
order to hold the flat connector
assembly tight on GA shield.
1-7
VPL-VW60
1-3-6. C Board
2 Two screws
(+BVTP 3
(+BVTP 3
x 12)
1 Four screws
(+BVTP 3
(+BVTP 3
x 12)
3 Claw
5 Four screws
(+PSW 3
(+PSW 3
x 8)
9 Radiation sheet (C)
7 Two screws
(+PSW 3
(+PSW 3
x 8)
6 Heat sink
(NCL)
(NCL)
!- C board
4 C board cover
8 C board holder,
C board shield
C board shield
CN7000
CN6000
CN5000
0 Spacer (Small)
1-3-7. Optics Unit Assembly
8 Lamp house
9 Lighting guard
7
Two screws
(+PSW 3
x 12)
3 Screw
(+PSW 4
(+PSW 4
x 12)
5 Ring (Lens)
6 Optics unit assembly
2 Lamp
1 Loosen three screws.
4 Optics unit fitting
attachment
attachment
1-8
VPL-VW60
1-3-8. Lamp Fan
0 Lamp fan
6 Exhaust duct
(QX)
(QX)
7 Exhaust duct (FZ),
Exhaust duct (FX)
Exhaust duct (FX)
5 Four screws
(+BVTP 3
(+BVTP 3
x 12)
8 Four fan dampers
9 Four fan dampers
(ZBL)
(ZBL)
GB board
CN701
CN701
3 Thee screws
(+BVTP 3
(+BVTP 3
x 12)
4 Remove the lamp fan section
in the direction of the arrow A.
in the direction of the arrow A.
1 Two fan connectors
2 Remove the harnesses
from the three claws.
from the three claws.
A
Click on the first or last page to see other RM-PJVW60 / VPL-VW60 service manuals if exist.