Sony RM-PJVW60 / VPL-VW60 Service Manual ▷ View online
1-9
VPL-VW60
1-3-9. TA Board
3 Three screws
(+BVTP 3
(+BVTP 3
x 12)
1 Three screws
(+BVTP 3
(+BVTP 3
x 12)
8 Three fan dampers
6 Two claws
9 Three fan dampers
4 Fan cover 84C
0 Panel fan
7 Fan cover 84I
5 Cushion (Lamp fan)
!- Two screws
(+BVTP 3
(+BVTP 3
x 12)
!= TA board
CN70
Fan cover 84C
Fan cover 84I
Claw
2
Do not catch the harness in the notch.
TA board
1-10
VPL-VW60
1-3-10. Lamp Power Supply
1 Two screws
(+PSW 3
(+PSW 3
x 8)
2 Two screws
(+BVTP 3
(+BVTP 3
x 12)
5 House cover
3 LPS shield
8 Fuse connector
assembly
assembly
4 Two screws
(+PSW 3
(+PSW 3
x 8)
9 Two screws
(+BVTP 3
(+BVTP 3
x 12)
0 Lamp power
supply section
supply section
!] Ballast support
!\ Lamp power supply
connector assembly
connector assembly
!- Two screws
(+BVTP 3
(+BVTP 3
x 12)
!; Lamp power supply
!= Remove the lamp power supply
in the direction of the arrow C.
in the direction of the arrow C.
![ LPS holder,
Sheet LPS, Heat sink LPS
Sheet LPS, Heat sink LPS
7 Remove the lamp power supply connector
assembly in the direction of the
assembly in the direction of the
arrows A and B.
6 Lamp power supply
connector assembly
connector assembly
B
A
Front Side
of Unit
of Unit
X1
X3
X2
Lamp power
supply
Front Side
of Unit
of Unit
Ballast support
Lamp power
supply
C
Note:
Remove the ballast support, and install
the ballast support to the new lamp
power supply with RTV bond.
1-11
VPL-VW60
1-3-11. GA Board and GB Board-1
GA board
GB board
GB board
GB board
2 Disconnect the connectors from each board.
CN800
CN702
CN301
CN600
CN600
CN601
CN601
CN700
CN701
4 Four screws
(+BVTP 3
(+BVTP 3
x 12)
3 Screw
(+PSW 3
(+PSW 3
x 8)
1
F holder
CN303
CN302
GA board
F holder
G sheet
Be careful not to break each flat
connector assembly.
connector assembly.
CN700
Flat connector
assembly B
assembly B
Flat connector
assembly B
assembly B
Flat connector
assembly A
assembly A
Flat connector
assembly
assembly
Front Side
of Unit
of Unit
6 Remove the GA/GB boards section
in the direction of the arrow.
in the direction of the arrow.
5
Press down the G sheet, and
disengage the hooks of the
G sheet from the two slits of the
GB shield.
G sheet from the two slits of the
GB shield.
G sheet
Two claws
of the G sheet
of the G sheet
Two slits of the GB sheet
Plastic tape
(UL tape, length ; 40mm)
(UL tape, length ; 40mm)
Plastic tape
(UL tape)
(UL tape)
GA shield
Flat connector assembly A
Flat connector
assembly A
assembly A
Note:
Keep the flat connector assembly toward the
GA board and place the plastic tape (UL tape)
on it, in order to hold the flat connector assembly
tight on GA shield.
Keep the flat connector assembly toward the
GA board and place the plastic tape (UL tape)
on it, in order to hold the flat connector assembly
tight on GA shield.
1-12
VPL-VW60
1-3-12. GA Board and GB Board-2
CN510
CN310
1 Two screws
(+PSW 3
(+PSW 3
x 8)
2 GA shield,
Wind guard
Wind guard
5 Four screws
(+PSW 3
(+PSW 3
x 8)
7 Four screws
(+PSW 3
(+PSW 3
x 8)
3 GB shield
4 Shield sheet (GB)
8 GB board
6 GA board
Shield sheet (GB)
GB shield
1-3-13. Lamp Fan (Sirocco)
1 Screw
(+PSW 3
(+PSW 3
x 8)
5 Two screws
(+BVTP 3
(+BVTP 3
x 12)
9 Lamp fan holder
!= Lamp fan (Sirocco)
6 Lamp fan cushion
8 Lamp fan plate
7 Three screws
(+BVTP 3
(+BVTP 3
x 12)
!- Three fan
dampers
dampers
0 Three fan
dampers
dampers
2 Lamp fan duct
GB board
CN701
CN701
Note: Cannot be reused.
4 Remove the lamp power supply connector
assembly in the direction of the arrow.
assembly in the direction of the arrow.
3 Fan connector
Lamp fan holder
Click on the first or last page to see other RM-PJVW60 / VPL-VW60 service manuals if exist.