Sony RM-PJVW200 / VPL-VW200 Service Manual ▷ View online
1-13
VPL-VW200
1-3-13. CB Board
When replacing the optical unit assembly,
refer to Service Know-How (page 1-33).
refer to Service Know-How (page 1-33).
2 CB board
attachment
attachment
0 Two screws
(+PSW M3
(+PSW M3
x 8)
!= Gasket C
8 Five screws
(+PSW M3
(+PSW M3
x 8)
9
Plate
CA
!-
C PC board holder
![ Screw
(+PSW M4
(+PSW M4
x 16)
!\
Optics unit assembly
1 Screw
(+PSW 3
(+PSW 3
x 12)
3 Two screws
(+PSW 3
(+PSW 3
x 8)
6
Twelve CA sheets
5
Claw
4 Two screws
(+PSW 3
(+PSW 3
x 12)
7 CA board
!]
Optics unit fitting
attachment
CN600
CN800
CN400
(B)
(R)
(G)
CA board
Plate
CA
C PC board holder
1-3-14. CA Board and Optics Unit Assembly
3 C PC board cover
2 Three screws
(+PSW M3
(+PSW M3
x 8)
1 Four screws
(+PSW M3
(+PSW M3
x 8)
5 Plate CB
7
Three connectors
(board to board)
4 Four screws
(+PSW M3
(+PSW M3
x 8)
6 Two screws
(+PSW M3
(+PSW M3
x 8)
0 CB board
9 Two sheets CB1
8 Four sheets CB2
CA board
CN200
CN201
CN202
CN901
CN902
CN900
CB board
1-14
VPL-VW200
1-3-16. Lamp Power Supply
1-3-15. GB Board
4 Three screws
(+PSW M3
(+PSW M3
x 8)
CN510
CN631
CN700
CN630
8 Four screws
(+PSW M3
(+PSW M3
x 8)
!=
GB board
!- Sheet GB
6 Cushion L
7 Cushion S
0 Shield cover (GB),
LVDS sheet
LVDS sheet
9 Shield case (GB)
1 Flat connector assembly
A
(30P)
2 Flat connector assembly
(24P)
(24P)
3 Flat connector assembly
B
(30P)
Front Side
of Unit
of Unit
5
Disconnect the specified connectors from the sheet LVDS.
GB Board
Four lead wire with
connectors (LVDS)
connectors (LVDS)
Flat connector assembly
A
(30P)
Sheet LVDS
Route the CN101 harness
outside CN100.
outside CN100.
Fix CN100 and
CN101 together
with an acetate tape.
CN101 together
with an acetate tape.
Do not route the
harness through
this hook.
harness through
this hook.
To CN100 on
the CB board.
the CB board.
To CN101 on
the CB board.
the CB board.
3 Four screws
(+PSW M3
(+PSW M3
x 8)
6 Screw
(+PSW M3
(+PSW M3
x 8)
4 Shield cover (LP)
8 Lamp power supply
5 Two screws
7 PC board spacer
J101
J202
JH1
JH2
1 Open the
reuse clamp.
reuse clamp.
2 Sheet LP
1-15
VPL-VW200
1-3-17. Igniter
6 Three screws
(+BVTP 3
(+BVTP 3
x 12)
5 Two screws
7 Two screws
(+PSW M3
(+PSW M3
x 8)
8 Plug cover
9 Two lamp plugs
0 Two screws
(+PSW 4
(+PSW 4
x 8)
!= Igniter
!- Sleeve ferrite clamp
3 Four screws
(+PSW M3
(+PSW M3
x 8)
4 Shield cover (LP)
Lamp power supply
JH1
JH2
Igniter
Sleeve ferrite clamp
Igniter
Insulating
sheet (I)
sheet (I)
1 Open the
reuse clamp.
reuse clamp.
2 Sheet LP
1-3-18. TA Board
3 Three screws
(+BVTP 3
(+BVTP 3
x 12)
7 Screw
(+BVTP 3
(+BVTP 3
x 12)
5 Six fan dampers
2 Fan connector
8 TA board
4
Fan cover
(84H)
6 D.C. motor
SFF22A/C-NP
SFF22A/C-NP
CN70
1 Open the
two reuse clamps.
two reuse clamps.
1-16
VPL-VW200
1-3-19. D.C. Motor SFF21C/C-NP (Right) and D.C. Motor SFF21C/C-NP (Left)
3 Screw
(+PSW M3
(+PSW M3
x 8)
3 Screw
(+PSW M3
(+PSW M3
x 8)
2 Spacer
2 Spacer
6 D.C. Motor
SFF21C/C-NP (Left)
SFF21C/C-NP (Left)
4 Fan cover (120R) (Right)
1 Fan connector
5 Four fan cushions
4 Fan cover (120R) (Right)
5 Four fan cushions
6 D.C. Motor
SFF21C/C-NP (Right)
SFF21C/C-NP (Right)
1 Fan connector
D.C. Motor SFF21C/C-NP (Left)
D.C. Motor SFF21C/C-NP (Right)
Click on the first or last page to see other RM-PJVW200 / VPL-VW200 service manuals if exist.