Sony RM-PJVW200 / VPL-VW200 Service Manual ▷ View online
1-9
VPL-VW200
1-3-8. TL Board
1-3-9. UA Board and UB Board
4 Two screws
(+BVTP 3
(+BVTP 3
x 12)
1 Screw
(+BVTP 3
(+BVTP 3
x 12)
5 UB board
3
UA board
CN20
CN26
CN25
2 UA holder
4 Two screws
(+PSW M3
(+PSW M3
x 8)
6 Screw
(+PSW M3
(+PSW M3
x 8)
5 Fan cover (120MDL),
Thermo bracket, etc.
Thermo bracket, etc.
3 TL board
CN71
CN71
9 TL board
2
Remove the harness
from the three claws.
1 Open the reuse clamp.
8 Fan cover
(120MDL)
(120MDL)
7 Thermo bracket
0 Fuse connector
assembly
assembly
1-10
VPL-VW200
1-3-10. HA Block Assembly
1 Two screws
(+BVTP 3
(+BVTP 3
x 12)
2 Push the shield cover (H) in the
direction of A, and slide it to
remove the HA block assembly.
direction of A, and slide it to
remove the HA block assembly.
!- HA block assembly
4 Two claws
7 Screw
(+BVTP 3
(+BVTP 3
x 12)
3 Screw
(+BVTP 3
(+BVTP 3
x 12)
9 HA board
8 Button (+)
5 Remove the shield plate (H)
in the direction of the arrow B.
in the direction of the arrow B.
0 Remove the shield cover (H)
in the direction of the arrow C.
in the direction of the arrow C.
CN60
CN60
6 Shield plate (H)
HA board
B
C
A
1-11
VPL-VW200
1-3-11. Hood Assembly and NR Board
1 Three screws
(+BVTP 3
(+BVTP 3
x 12)
2 Rear duct (F),
Lamp stopper
Lamp stopper
3 Lamp stopper
spring
spring
!= Claw
![ Lamp stopper
Rear duct (F)
4 Three screws
(+BVTP 3
(+BVTP 3
x 12)
5 Rear duct (I)
Lamp stopper spring
Lamp stopper
9 Screw
(+PSW M3
(+PSW M3
x 8)
!- Hood assembly
6
Screw
(+BVTP 3
x 12)
0 NR board
8 Remove the mesh (R) in the
direction of the arrow.
direction of the arrow.
7 Two claws
CN50
1-12
VPL-VW200
1-3-12. Optics Unit Section
2 Three screws
(+PSW M4
(+PSW M4
x 16)
4 Two screws
(+BVTP 3
(+BVTP 3
x 12)
5 V
board
3
Remove the optics unit
section in the direction
of the arrow.
of the arrow.
CN30
Fan connector
GB board
CN701
CN701
Four lead wire with connectors (LVDS)
CA board
CB board
GB board
CN101
CN701
CN800
Fan
connector
connector
Flat connector assembly A
(30P)
CN100
1 Remove all connectors respectively.
Front Side
of Unit
of Unit
CN100
CN101
CN102
CN103
Be careful not to break each flat connector assembly.
GB Board
Four lead wire with
connectors (LVDS)
connectors (LVDS)
Flat connector assembly
A
(30P)
Sheet LVDS
Front Side
of Unit
of Unit
Route the CN101 harness
outside CN100.
outside CN100.
Fix CN100 and
CN101 together
with an acetate tape.
CN101 together
with an acetate tape.
Do not route the
harness through
this hook.
harness through
this hook.
To CN100 on
the CB board.
the CB board.
To CN101 on
the CB board.
the CB board.
Click on the first or last page to see other RM-PJVW200 / VPL-VW200 service manuals if exist.