DOWNLOAD Sony PXW-FS7 / PXW-FS7K Service Manual ↓ Size: 27.59 MB | Pages: 127 in PDF or view online for FREE

• Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
• Do not touch the conductive side of flexible boards with bare hands.
• Plug in a flexible board straight, fully into the connector until it reaches the end inside.

Flexible

Board

Flexible
Board

Connector

Connector

Reference line

Flexible
Board

Connector

Connector

Flexible

Board

Reference line

Connector

Connector

Flexible
Board

Flexible

Board

Reference line

OK 

(The flexible board was plugged in 
straight and completely)

(The flexible board was plugged in 
crooked.)

NG 

NG 

(The flexible board was not plugged in 
completely.)

• When opening the connector's holder in direction A, do not open it with excessive force.

Holder

Connector

Flexible Board

A

A

• When closing the connector's holder, press it evenly while pushing a flexible board in direction B.

Holder

Insulation side

Connector

Flexible Board

B

• Make sure that the flat cable and flexible board are not cracked or bent at the contact end.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

• Do not apply excessive force to the gilded flexible board.

• The proper way to disconnect a connector is to grab the connector instead of the wires. If you pull on the wires,

they might be broken.

• The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they

might be broken.

PXW-FS7/PXW-FS7K

2-1

Use the AC power adaptor.

PXW-FS7/PXW-FS7K

2-2

After replacing the following boards, be sure to perform the update of firmware.
About the update, consult with each Head Quarters.

• AVP-25 board (Overall Section-5)
• DPR-365 board (Overall Section-5)
• VIF-58 board (Overall Section-3)
• KY-739 board ( Inside Panel Section-2)

Refer to following items on the ADJUST tab of the Adjust Manual for destination data input, USB Serial number and
Product ID input when replacing DPR-365 board.

• DPR-365 board: Initialize Machine ID (DPR board)

PXW-FS7/PXW-FS7K

2-3

The unit is provided with the Service menu that is useful for maintenance and adjustment. The menu content is displayed
on the screen.
The Service menu consists of the following menus.

Information

Information and status of the unit display

Version 1～3

Firmware software and FPGA, etc. display

• Press the [MENU] button to display the setup menu.
• Turn the [SEL/SET] dial to place the cursor at “Hours Meter” of the System menu.
• Press the [MENU] button while pressing the [SEL/SET] dial and the [ASSIGN 1] button simultaneously.

The Service menu is added to the setup menu.

The Service menu is kept in the setup menu unless the power is turned off, after add the Service menu.
It is able to switch on/off the Service menu display by pressing the [MENU] button.
The Service menu is deleted from the setup menu when the power is turned off.

 for details of each items.

Factory Reset

Reset

Execute/Cancel
(Cancel)

Reset to the factory setting (for Service menu)

Information

Serial Number

–

Displays the serial number of the unit

Imager Temp.

–

Displays the temperature of the image sensor

Main Board Temp

–

Displays the internal temperature (around
main board)

Log Dump

Execute/Cancel
(Cancel)

Outputs log of this unit

Version 1

Package

– 　

Displays firmware version

IC2300 (AVP-25 board)
IC2400 (DPR-365 board)
IC2400 (DPR-365 board)
IC0100 (DPR-365 board)
IC1900 (DPR-365 board)

– 　

Displays each IC version

Version 2

IC1100 (DPR-365 board)
IC0201 (VIF-58 board)

– 　

Version 3

IC3102 (AVP-25 board)
IC2803 (DPR-365 board)
IC631 (KY-739 board)

–

The Factory Reset menu is used to restore the factory settings (default settings) of the Service menu.

PXW-FS7/PXW-FS7K

2-4