Sony HDR-TD10 / HDR-TD10E (serv.man2) Service Manual ▷ View online
HDR-TD10/TD10E_L2
1-1
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2. PRECAUTION ON REPLACING THE VC-625 BOARD
Note the following when replacing the board.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB SERIAL SAVE
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Angular Velocity Sensor
When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor SE7501 (PITCH/YAW).
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.
Note: The sensor sensitivity of SE7501 (PITCH/YAW) on VC-625 board is written only repair parts.
VC-625 BOARD (SIDE A)
G1
G2
PPP:
PITCH sensor sensitivity
PITCH sensor sensitivity
YYY:
YAW sensor sensitivity
YAW sensor sensitivity
YYY
PPP
VC-625 BOARD (SIDE A)
G1
G2
PPP:
PITCH sensor sensitivity
PITCH sensor sensitivity
YYY:
YAW sensor sensitivity
YAW sensor sensitivity
YYY
PPP
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display.Details of the self-diagnosis functions are provided in the
Instruction manual.
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display.Details of the self-diagnosis functions are provided in the
Instruction manual.
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
0 0
3 2
C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.
13 ....
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
Viewfinder or LCD screen
0 0
3 2
C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.
13 ....
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
Viewfinder or LCD screen
1-3-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the InfoLITHIUM battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or place it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the memory card.
Insert a new memory card.
Insert a new memory card.
C
1
3
0
2
Access error
Remove the power source. Reconnect it again and operate your cam-
corder again.
corder again.
C
1
3
0
3
Access error (External media)
Turn power off and turn power on again.
C
1
3
0
4
Drive fault (External media)
Turn power off and turn power on again.
C
E
3
2
6
1
6
0
0
0
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does not recover, check
the focus MR sensor of lens device (pin r;, ra of CN5001 or pin r;,
ra
the focus MR sensor of lens device (pin r;, ra of CN5001 or pin r;,
ra
of CN5005 on the LD-281 board). If it is OK, check the focus motor
drive IC (IC1601 on the VC-625 board).
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value. (Note 1)
E
3
1
0
0
Drive fault
Turn power off and turn power on again.
Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.
Note 2: Functions of codes with * mark are not provided in this unit.
– ENGLISH –
( )
HDR-TD10/TD10E_L2
1-2
– ENGLISH –
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
Inspect the lens device zoom reset signal (pin wd of CN5001 or pin wd
of CN5005 on the LD-281 board) when zooming is performed when
the zoom lever is operated, and the zoom motor drive circuit (IC1601
on the VC-625 board) when zooming is not performed.
E
6
1
1
1
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of
the zoom lens occurred simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E
6
1
3
0
Reset position detection error on the stepper
iris initializing
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive block (CN5001
pin rf, t; or CN5005 pin rf, t; on LD-281 board).
pin rf, t; or CN5005 pin rf, t; on LD-281 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
･ Case of the iris blades do not close normally Replace the lens de-
･ Case of the iris blades do not close normally Replace the lens de-
vice).
･ Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens device is normal.
･ Case of LCD is not displayed normally Check that connection be-
･ Case of LCD is not displayed normally Check that connection be-
tween lens device (CM-114) and CN1010 or CN1011 on VC-625
board by FP-1386 flexible board.
･ Case of LCD is displayed normally Replace the lens device.
E
6
2
0
0
Handshake correction function does not work
well. (With PITCH angular velocity sensor
output stopped.)
Inspect PITCH angular velocity sensors (SE7501 on the VC-625
board) peripheral circuits.
E
6
2
0
1
Handshake correction function does not work
well. (With YAW angular velocity sensor
output stopped.)
Inspect YAW angular velocity sensors (SE7501 on the VC-625 board)
peripheral circuits.
E
6
2
0
2
Abnormality of IC for steadyshot.
Refer to [1-5-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Oc-
curred].
E
6
2
0
3
IC for steadyshot and micro controller com-
munication abnormality among.
Inspect the steadyshot circuit (IC5501 on the LD-281 board).
E
6
2
0
4
Image vibration correction during
handshake function does not work.
Inspect the image vibration angular velocity sensors (SE7701 on the
LD-281 board) peripheral circuits.
E
6
2
1
0
Shift lens initializing failure.
Replacement of lens device. (Note 3) If an error occurs again, replace
the LD-281 board.
E
6
2
1
1
Shift lens overheating (Pitch)
Refer to [1-5-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred].
E
6
2
1
2
Shift lens overheating (Yaw)
Refer to [1-5-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred].
E
6
2
2
0
Abnormality of thermistor.
Refer to [1-5-4. E : 62 : 20 (Abnormality of Thermistor) Occurred].
E
9
1
0
1
Abnormality when flash is being charged.
Checking of flash unit or replacement of flash unit (FL40000).
E
9
1
0
2
Abnormality of flash unit.
Checking of flash unit or replacement of flash unit (FL40000).
E
9
1
0
3
Abnormality of flash unit Temperature
detection.
Checking of flash unit or replacement of flash unit (FL40000).
E
9
2
0
1
Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Connect the
CN4002 of MM-100 board with CN1009 of VC-625 board.
Check each output of DC/DC converter (IC4301) on CN4001 of
MM-100 board with the AC adaptor connected DC JACK.
(The minimum connection to periphery)
E
9
4
0
0
Fault of writing or erasing the flash memory
Inspect the flash memory (IC8101, IC8202 on the MM-100 board).
E
9
4
0
1
Internal flash memory fault
Inspect the flash memory (IC8101, IC8202 on the MM-100 board).
E
9
4
0
2
BGM data error
Check the CPU (IC1601 on the VC-625 board).
E
9
5
0
0
GPS hardware error
Turn power off and turn power on again.
E
9
6
0
0
Map area mount error
Turn power off and turn power on again.
E
9
7
0
0
Projector hardware error
Turn power off and turn power on again.
Note 3: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-4. METHOD OF COPING WITH SHIFT LENS ERROR
LD-281 BOARD (SIDE A)
LD-281 BOARD (SIDE B)
IC5501
C5527
C5528
C5525
C5526
C5529
C5530
C5531
C5532
R5506
Fig. 1
Measurement points on the LD-281 board
about 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R5506 on the LD-281 board
1-4-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the LD-281 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens device (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1601 of VC-625 board) periphery.
the camera control circuit (IC1601 of VC-625 board) periphery.
Note: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
*
*
*
*
*
HDR-TD10/TD10E_L2
1-3
– ENGLISH –
1-4-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Order
AdjustBlock
AdjustCode
Order
1
If a caution occurs only in the 2D mode, perform the procedure beginning with step 6.
2
Start the Adjust Manual in the Adjust Station and execute the [
Measure to E:62:11/12 for 2D
] on the
[SERVICE] tab
in the 3D mode
.
3
Check if the shift lens moves while setting the order
2
.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order
When the shift lens moved, proceed to the order
4
.
4
While setting the order 1, measure with an oscilloscope the output voltage of
C5529 and C5530
in
the periphery of IC5501 on the LD-281 board to check the output voltage varies.
5
If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order
When the output voltage varied, proceed to the order
6
.
6
Start the Adjust Manual in the Adjust Station and execute the [
Measure to E:62:11/12 for 2D
] on the
[SERVICE] tab
in the 2D mode
.
7
Check if the shift lens moves while setting the order 6.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.
8
While setting the order 1, measure with an oscilloscope the output voltage of C5525 and C5526 in
the periphery of IC5501 on the LD-281 board to check the output voltage varies.
the periphery of IC5501 on the LD-281 board to check the output voltage varies.
9
If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 10.
When the output voltage varied, proceed to the order 10.
10
Turn the power OFF.
11
While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the
LD-281 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
LD-281 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
12
If the output voltage change as shown in Fig. 2, replace the lens device (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-625 board
and IC5501 of LD-281 board) periphery.
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-625 board
and IC5501 of LD-281 board) periphery.
Note: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2011.04
1-4-3.E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Order
AdjustBlock
AdjustCode
Order
1
If a caution occurs only in the 2D mode, perform the procedure beginning with step 6.
2
Start the Adjust Manual in the Adjust Station and execute the [
Measure to E:62:11/12 for 2D
] on the
[SERVICE] tab
in the 3D mode
.
3
Check if the shift lens moves while setting the order
2
.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order
When the shift lens moved, proceed to the order
4
.
4
While setting the order 1, measure with an oscilloscope the output voltage of
C5531 and C5532
in
the periphery of IC5501 on the LD-281 board to check the output voltage varies.
5
If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order
When the output voltage varied, proceed to the order
6
.
6
Start the Adjust Manual in the Adjust Station and execute the [
Measure to E:62:11/12 for 2D
] on the
[SERVICE] tab
in the 2D mode
.
7
Check if the shift lens moves while setting the order 6.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.
If the shift lens does not move, replace the lens device (Note).
When the shift lens moved, proceed to the order 8.
8
While setting the order 1, measure with an oscilloscope the output voltage of C5527 and C5528 in
the periphery of IC5501 on the LD-281 board to check the output voltage varies.
the periphery of IC5501 on the LD-281 board to check the output voltage varies.
9
If the output voltage does not vary, replace the lens device (Note).
When the output voltage varied, proceed to the order 10.
When the output voltage varied, proceed to the order 10.
10
Turn the power OFF.
11
While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the
LD-281 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
LD-281 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
12
If the output voltage change as shown in Fig. 2, replace the lens device (Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-625 board
and IC5501 of LD-281 board) periphery.
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-625 board
and IC5501 of LD-281 board) periphery.
Note: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-4-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Confirm the connections of flexible flat cables and connectors between the lens device and LD-281 board.
3
In case of no malfunction of connections, replace the lens device with new one (Note) . When the error has occurred in spite of the lens
replacement, replace LD-281 board with new one.
replacement, replace LD-281 board with new one.
Note: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-TD10/TD10E_L2
1-4
1-5. PRECAUTION ON REPLACING THE CABINET (BOTTOM)
1-5-1. Precaution on ordering the CABINET (BOTTOM)
The model display adopts the laser printing method.
Therefore, the Cabinet (Bottom) for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
Therefore, the Cabinet (Bottom) for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
Note: After replacing the Cabinet (Bottom) , the serial number for it
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the
serial number in the repair data.
Inform a customer of the serial number change and change the
serial number in the repair data.
HDR-TD10 (US Model)
Part No.
Description
A-1825-625-A CABINET (BOTTOM (TD10-U2))
HDR-TD10 (J Model)
Part No.
Description
A-1825-626-A CABINET (BOTTOM (TD10-J1))
HDR-TD10 (CND Model)
Part No.
Description
A-1825-628-A CABINET (BOTTOM (TD10-CA2))
HDR-TD10 (E (NTSC) Model)
Part No.
Description
A-1825-629-A CABINET (BOTTOM (TD10-E23))
HDR-TD10 (KR Model)
Part No.
Description
A-1825-630-A CABINET (BOTTOM (TD10-KR2))
HDR-TD10E (AEP Model)
Part No.
Description
A-1825-631-A CABINET (BOTTOM (TD10-CEN))
HDR-TD10E (NE Model)
Part No.
Description
A-1825-632-A CABINET (BOTTOM (TD10-CEL))
HDR-TD10E (E (PAL) Model)
Part No.
Description
A-1825-633-A CABINET (BOTTOM (TD10-E34))
HDR-TD10E (HK, JE Model)
Part No.
Description
A-1825-635-A CABINET (BOTTOM (TD10-HK1))
HDR-TD10E (CH Model)
Part No.
Description
A-1825-636-A CABINET (BOTTOM (TD10-CN2))
HDR-TD10E (AUS Model)
Part No.
Description
A-1825-637-A CABINET (BOTTOM (TD10-AU2))
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Ver. 1.1 2011.04
1-5-2. Precaution on Replacing the CABINET (BOTTOM) for J Models
The year of manufacture on the labels should be the same as the previous Cabinet (Bottom) (circled portions shown on the below).
Example: For the figure below, attach the “Made of 11 years” label.
Example: For the figure below, attach the “Made of 11 years” label.
* The replacement label and “inset (how to affix)” are supplied together with Cabinet (Bottom) for service.
HDR-TD10 (J Model)
* Manufacturing year
*
Affix the label
1-5-3. Precaution on Replacing the CABINET (BOTTOM) for US Models
The date of manufacture on the labels should be the same as the previous Cabinet (Bottom) (circled portions shown on the below).
Example: For the figure below, attach the “1A” labels.
Example: For the figure below, attach the “1A” labels.
* The replacement labels and “inset (how to affix)” are supplied together with Cabinet (Bottom) Assy for service.
HDR-TD10 (US Model)
* Manufacturing year
*
Affix the label
1-5-4. Precaution on Replacing the CABINET (BOTTOM) for KR Models
The date of manufacture on the labels should be the same as the previous Cabinet (Bottom) (circled portions shown on the below).
Example: For the figure below, attach the “2011-01” label.
Example: For the figure below, attach the “2011-01” label.
* The replacement label and “inset (how to affix)” are supplied together with Cabinet (Bottom) for service.
HDR-TD10 (KR Model)
* Manufacturing year
*
Affix the label
– ENGLISH –
Click on the first or last page to see other HDR-TD10 / HDR-TD10E (serv.man2) service manuals if exist.