Sony HDR-PJ800 / HDR-PJ810 / HDR-PJ810E / HDR-PJ820 / HDR-PJ820E (serv.man2) Service Manual ▷ View online
1-5
HDR-PJ800/PJ810/PJ810E/PJ820/PJ820E_L2
– ENGLISH –
1-7. DISCHARGE OF LED FLASH/VIDEO LIGHT
This model is provided with a flash unit using LED Flash/Video light.
Therefore, the LED Flash/Video light does not have high voltage part and does not need to be discharged.
Therefore, the LED Flash/Video light does not have high voltage part and does not need to be discharged.
1-8. NOTE ON REPLACING PROJECTOR UNIT
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart.
When a defective part has been clarified, repair the projector according to the check result.
chart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK
OK
NG
NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED.
( 1)
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (
*1)
Replace PJ board. (
*1)
Replace both projector unit (light emitting block)
and PJ board. (
and PJ board. (
*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Enter the number on the label attached to the unit.
Serial number input
LD40
LD40
Syywwnnnnn
Enter the red part.
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (
*1)
Replace PJ board. (
*1)
Replace both projector unit (light emitting block)
and PJ board. (
and PJ board. (
*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Enter the number on the label attached to the unit.
Serial number input
LD40
LD40
Syywwnnnnn
Enter the red part.
1-6
HDR-PJ800/PJ810/PJ810E/PJ820/PJ820E_L2
– ENGLISH –
1-9 . LENS DEVICE (LSV-1400B) REPLACING METHOD
Lens Cap
A protective Lens Cap is attached to each new
service Lens Block.
Carry out replacement work with this Lens Cap
attached.
service Lens Block.
Carry out replacement work with this Lens Cap
attached.
Note:
Removal
(1) Remove the five screws.
TOP
FRONT
Screw
Screw
Screw
Screw
Screw
(2) Remove the four screws.
TO
P
FRONT
Screw
Screw
Screw
Screw
(3) Disconnect the connector and peel off the adhesive part of the LF-
2025 Flexible Board.
TO
P
FRON
T
Adhesive part
Connector
LF-2025 Flexible Board
(4) Peel off the adhesive part of the LF-2026 Flexible Board.
TO
P
FRONT
Adhesive part
LF-2026 Flexible Board
(5) Remove the Sheet Metal (C), Stopper while detaching the four bosses.
TO
P
FRONT
Sheet Metal (C),
Stopper
Stopper
Bosses
Bosses
(6) Peel off the adhesive part of the LF-2063 Flexible Board.
T
OP
FR
ONT
Adhesive part
LF-2063 Flexible Board
(7) Remove the Frame (F-Sub-A), Frame (F-Sub-B), and Ball Bearing
while detaching the two bosses and the shaft.
TO
P
FRONT
Bosses
Frame (F-Sub-A),
Frame (F-Sub-B),
Ball Bearing
Frame (F-Sub-B),
Ball Bearing
Shaft
(8) Remove the six screws and remove the Frame (E-Sub-A), Frame
(E-Sub-B), and Ball Bearing while detaching the four bosses and
the shaft.
the shaft.
TO
P
FR
ON
T
TO
P
FRONT
TO
P
FRO
NT
Screw
Screw
Screw
Screw
Screw
Screw
Bosses
Bosses
Frame (E-Sub-A),
Ball Bearing
Ball Bearing
Frame (E-Sub-B)
Shaft
1-7
HDR-PJ800/PJ810/PJ810E/PJ820/PJ820E_L2
– ENGLISH –
(9) Disconnect the connector and remove the four screws to detach the
Sheet Metal (B), Stopper, Motor B, and LF-2025 Flexible Board.
TO
P
FRONT
TO
P
FRONT
Connector
Sheet Metal (B),
Stopper,
Motor B
LF-2025 Flexible Board
Stopper,
Motor B
LF-2025 Flexible Board
Screw
Screw
Screw
Screw
(10) Disconnect the connector and remove the three screws to detach
the Motor B.
Peel off the adhesive part of the LF-2025 Flexible Board.
Sheet Metal (B),
Stopper
Stopper
Adhesive part
Connector
Motor B
LF-2025 Flexible
Board
Board
Screw
Screw
Screw
(11) Remove the three screws while turning the Plate of the Motor A to
detach the Motor A.
TOP
FRONT
TO
P
FRONT
TO
P
FRONT
TO
P
FRONT
Screw
Screw
Screw
Screw
Screw
Screw
Plate of the Motor A
Plate of the Motor A
Plate of the Motor A
Motor A
(12) Remove the screw, and remove the boss and the claw to detach the
Front Ornament.
TO
P
FRONT
Boss
Claw
Screw
Front Ornament
(13) Peel off the CM Radiation Sheet.
TO
P
FRONT
CM Radiation Sheet
(14) Peel off the adhesive part of the LF-2026 Flexible Board.
TO
P
FRONT
Adhesive part
LF-2026 Flexible Board
(15) Remove the two screws and disconnect the connector to detach the
Sheet Metal (D-Sub), the LF-2026 Flexible Board.
TOP
FRONT
TOP
FRONT
Connector
Screw
Screw
Sheet Metal (D-Sub),
LF-2026 Flexible Board
LF-2026 Flexible Board
(16) Peel off the adhesive part of the LF-2026 Flexible Board.
Adhesive part
LF-2026 Flexible Board
Sheet Metal (D-Sub)
1-8
HDR-PJ800/PJ810/PJ810E/PJ820/PJ820E_L2
– ENGLISH –
(17) Remove the two screws and remove the two bosses to detach the
Sheet Metal (A).
Peel off the Polyimide Sheet.
TO
P
FRON
T
Sheet Metal (A)
Bosses
Polyimide Sheet
Screw
Screw
(18) Disconnect the connector and peel off the adhesive part of the LF-
2063 Flexible Board.
TOP
FRON
T
Adhesive part
Connector
LF-2063 Flexible Board
(19) Remove the two screws and remove the CM-1007 Board, Seal
Rubber, Optical Filter Block from the Lens Device (LSV-1400B).
TO
P
FRONT
Screw
Screw
Optical Filter Block
Seal Rubber
CM-1007 Board
Lens Device (LSV-1400B)
Installation
(1) Install the Optical Filter Block, Seal Rubber, CM-1007 Board to the
Lens Device (LSV-1400B), and then tighten two screws in the order
shown in the figure below.
shown in the figure below.
Tightening torque = 0.13 ± 0.01N · m (1.3 ± 0.1kg f · cm)
Note :
2
1
Optical Filter Block
(Note)
(Note)
Optical Filter Block
Refer to“Assembly-3: How to distinguish the side of
Optical Filter Block facing to Lens Device.”.
Optical Filter Block facing to Lens Device.”.
TOP
FRONT
Screw
Screw
Seal Rubber
CM-1007 Board
Lens Device (LSV-1400B)
(2) Connect the connector of the LF-2063 Flexible Board and stick the
adhesive part of the Flexible Board.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
TO
P
FRONT
Adhesive part
Connector
LF-2063 Flexible Board
LF-2063 Flexible Board
Shape and sticking position
of the Adhesive Sheet
of the Adhesive Sheet
Adhesive Sheet
(3) Stick the Polyimide Sheet.
While attaching the two bosses, install the Sheet Metal (A), and then
tighten two screws in the order shown in the figure below.
tighten two screws in the order shown in the figure below.
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
TOP
FRONT
2
1
Sheet Metal (A)
Bosses
Polyimide Sheet
Screw
Screw
(4) Stick the adhesive part of the LF-2026 Flexible Board to the Sheet
Metal (D-Sub) while positioning it with the two holes.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
Holes
Shape and sticking position
of the Adhesive Sheet
of the Adhesive Sheet
Adhesive Sheet
Adhesive part
LF-2026 Flexible Board
LF-2026 Flexible Board
Sheet Metal (D-Sub)
(5) Connect the connector of the Flexible Board of the Lens Device
(LSV-1400B).
Install the LF-2026 Flexible Board, Sheet Metal (D-Sub).
TOP
FRONT
Connector
Flexible Board of the Lens Device (LSV-1400B)
Sheet Metal (D-Sub),
LF-2026 Flexible Board
LF-2026 Flexible Board
(6) While attaching the boss and the claw, install the Front Ornament,
and then tighten three screws in the order shown in the figure below.
Screw (A)
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
Screw (B)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Tightening torque = 0.12 ± 0.01N · m (1.2 ± 0.1kg f · cm)
Screw (B)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
1
2
3
TO
P
FR
ONT
Boss
Claw
Screw (B)
Screw (B)
Screw (A)
Front Ornament
Click on the first or last page to see other HDR-PJ800 / HDR-PJ810 / HDR-PJ810E / HDR-PJ820 / HDR-PJ820E (serv.man2) service manuals if exist.