Sony HDR-PJ780E / HDR-PJ780VE / HDR-PJ790 / HDR-PJ790E / HDR-PJ790V / HDR-PJ790VE (serv.man2) Service Manual ▷ View online
2-6
HDR-PJ780E/PJ780VE/PJ790/PJ790E/PJ790V/PJ790VE_L2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
A-1917-760-A RH-1001 BOARD, COMPLETE
152
4-443-885-01
HOLDER (L (429)), JACK
153
4-422-359-01
HEAT SINK (B), VC
154
4-425-108-11
SHEET (A), RADIATION
155
4-422-357-01 FRAME,
RH
156
4-422-370-11
SHEET, CM FLEXIBLE GUARD
157
1-887-508-11
FP-2108 FLEXIBLE BOARD
158
1-887-509-11
FP-2109 FLEXIBLE BOARD
159
4-296-785-01
SHEET (LCD247), WAVE ABSORPTION
160
1-885-623-21
FP-1557 FLEXIBLE BOARD
161
A-1919-754-A VC-1014 BOARD, COMPLETE (SERVICE)
162
4-443-883-01
GUARD (429), CM FLEXIBLE (Note 3)
BH7001 1-251-928-21
SOCKET, BATTERY (Note 1)
BT7001 1-756-134-15
BATTERY, LITHIUM (SECONDARY) (Note 1)
C7207
1-116-781-11
DOUBLE LAYERS 0.35F 20% 5.5V (Note 2)
#3
2-660-401-01 SCREW(M1.7),NEW
TRU-STAR,P2
#11
3-078-890-11 SCREW,
TAPPING
2-1-4. MAIN BOARD SECTION
ns: not supplied
1. Remove in numerical order (
1
to
5
) in the left figure.
DISASSEMBLY
Screw
1
#3 X 3
#3
Back View
3
#3 X 2
Back View
Bottom View
#3
#3
5
#3 X 3
#3
Back View
Note
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Note 1: Replace the battery holder (BH7001) together when replac-
ing the lithium storage battery (BT7001) on the RH-1001
board. (The battery holder removed once cannot be useda-
gain.)
board. (The battery holder removed once cannot be useda-
gain.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
and attach new lithium storage battery next.
Note 1: RH-1001基板のリチウム蓄電池 (BT7001) を交換する場合は
バッテリホルダ (BH7001) も同時に新品に交換してくださ
い。
い。
(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は,先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
らリチウム蓄電池を装着してください。
注意 :
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換して
ください。
使用済み電池は,取扱指示に従って処分してください。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換して
ください。
使用済み電池は,取扱指示に従って処分してください。
Note 2: This model is provided with a flash unit using LED Flash/
Video light (C7207).
Therefore, the LED Flash/Video light (C7207) does not
have high voltage part and does need to be discharged.
have high voltage part and does need to be discharged.
Note 2: この機種ではLEDを使用したLEDフラッシュ /ビデオライト
(C7207)を使用しております。
そのため高電圧部分が無く,放電は不要です。
Note 3: Refer to “Assembly-3: Installation Cautions of the CM Flexible
Guard.”.
Note 3: Assembly-3: Installation Cautions of the CM Flexible
Guard. を参照してください。
RH-1001
VC-1014
A
A
B
B
A
C
C
C7207
(Note 2)
(Note 2)
#3
#11
ns
#3
#3
#3
152
156
154
(Claws)
(Claw)
(Boss)
: BT7001 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-47)
Board on the mount position.
(See page 6-47)
160
159
157
158
Lens Section
(See page 2-7)
BT7001
(Note 1)
(Note 1)
BH7001
(Note 1)
(Note 1)
4
162
(Note 3)
3
155
5
161
1
151
2
153
#3:
2.5
1.7
M1.7 X 2.5
(Red)
2-660-401-01
(Red)
2-660-401-01
#11:
4.0
1.7
M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
(Silver)
3-078-890-11
2-7
HDR-PJ780E/PJ780VE/PJ790/PJ790E/PJ790V/PJ790VE_L2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
201
4-422-372-01
ORNAMENT, LENS (Note 3)
202
1-856-033-21
OPTICAL FILTERBLOCK (OFB-03-52)
203
3-216-044-01
RUBBER (1270), SEAL
204
A-1785-655-A CMOS BLOCK ASSY (1390) -077
(including IC6701 (CMOS imager)) (Note 1)
205
4-422-373-01
SHEET, CM RADIATION (Note 2)
206
4-422-356-01 FRAME,
LD
207
4-422-355-01 FRAME,
VC
208
1-887-507-11
FP-2107 FLEXIBLE BOARD
210
1-887-716-11
FP-2127 FLEXIBLE BOARD
211
A-1919-701-A LD-1007 BOARD, COMPLETE (SERVICE)
212
4-443-879-01
HEAT SINK (429), VC
213
4-443-881-01
SHEET (429), VC RADIATION
#2
2-635-562-31 SCREW
(M1.7)
#3
2-660-401-01 SCREW(M1.7),NEW
TRU-STAR,P2
#12
3-080-204-21 SCREW,
TAPPING,
P2
2-1-5. LENS SECTION
1. Remove in numerical order (
1
to
6
) in the left figure.
DISASSEMBLY
1
#3 X 1 → #2 X 1
Top View
Right View
#3
#2
3
#3 X 1 → #2 X 1
Front View
Front View
#2
#3
4
#3 X 3
Back View
#3
5
#3 X 5
Back View
Left View
Top View
#3
#3
#3
Screw
Note
Note 2: Do not reuse the CM Radiation Sheet because its adhesive
force decreases when it is removed once.
Note 2: CM Radiation Sheetは一度剥がすと粘着力が弱くなるため,
再利用はしないでください。
Note 3: Refer to “Assembly-4: The Method of removing of Lens
Ornament.”.
Note 3: Assembly-4: The Method of removing of Lens Ornament.
を参照してください。
Note 1: Be sure to read “Precautions for Replacement of Imager” on
page 6-1 of Level3 when changing the imager.
Note 1: イメージャの交換時はLevel3の6-1ページ, イメージャ交
換時の注意 を必ずお読みください。
Refer to "Caution for Handling
the Lens Device (LSV-1550A)"
the Lens Device (LSV-1550A)"
#12
#3
#3
#3
#2
#3
#2
#3
#3
#3
#3
6
3
LCD Section-1
(See page 2-10)
2
212
4
211
5
207
206
203
205
(Note 2)
213
208
201
(Note 3)
208
210
202
1
Cabinet (F) Section
(See page 2-9)
Lens Block Section
(See page 2-8)
204
(including IC6701
(CMOS imager))
(Note 1)
(CMOS imager))
(Note 1)
2
(Bosses)
#2:
4.0
1.7
M1.7 X 4.0
(Black)
2-635-562-31
(Black)
2-635-562-31
#3:
2.5
1.7
M1.7 X 2.5
(Red)
2-660-401-01
(Red)
2-660-401-01
#12:
1.7
5.0
M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
(Black)
3-080-204-21
2-8
HDR-PJ780E/PJ780VE/PJ790/PJ790E/PJ790V/PJ790VE_L2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
251
4-300-860-01
RUBBER, EDGE OF MECHANICAL (*)
252
1-855-149-12 MOTOR,
A
253
4-411-437-02 ORNAMENT,
FRONT
254
1-855-148-12 MOTOR
B
255
1-885-785-11
LF-153 FLEXIBLE BOARD (Note 6)
256
1-885-778-12
LF-148 FLEXIBLE BOARD (Note 6)
257
4-441-672-01
SHEET, ADHESIVE (Note 2)
258
2-580-751-01
SHEET, POLYIMIDE (Note 3, 4)
259
4-422-373-01
SHEET, CM RADIATION (Note 5)
260
A-1854-190-A SERVICE, LSV-1550A (SERVICE)
#277
4-300-113-21
TAPPING (1.7) (CH)
#278
4-423-712-01
SCREW, 0+P2 M2 NEW TRU-STAR (Note 1)
#279
4-423-713-01
SCREW, 0+P2 B1.7
Screw
Note
Note 1: Machining for preventing screws from loosening is applied to
this screw.
If this screw is turned a few times or more, do not reuse it and
use a new one.
use a new one.
Note 1: このねじは緩み防止加工が施されています。
2 ∼ 3回以上外した場合は,再利用せず新品のねじを使用
してください。
してください。
Note 3: Cut the polyimide tape for specified size.
Note 3: ポリイミドシートは,指定の寸法にカットして使用してく
ださい。
Note 4: When the bond has been removed, cut the Polyimide Sheet
to the specified size and stick it.
Note 4: ボンドを剥がした場合は,ポリイミドシートを指定のサイ
ズに切って貼り付けてください。
Note 5: Do not reuse the CM Radiation Sheet because it is adhesive
force decreases when it is removed once.
Note 5: CM Radiation Sheetは一度剥がすと粘着力が弱くなるため,再
利用はしないでください。
Note 6: When any of these Flexible Boards is peeled off and decreased
adhesive force of the Adhesive Part or wrinkle or break of the
Flexible Board is found, replace the defective Flexible Board
with a new one.
Flexible Board is found, replace the defective Flexible Board
with a new one.
Note 6: これらのフレキを剥がした場合は,粘着部の粘着力の低下,
フレキのしわ,折れが認められた場合は新品に交換してく
ださい。
ださい。
Note 2: Cut the SHEET, ADHESIVE (4-441-672-01) as shown in the
balloon in the figure and use it.
Note 2: SHEET, ADHESIVE (4-441-672-01) は図中の吹き出しのよう
に切って使用すること。
2-1-6. LENS BLOCK SECTION
ns: not supplied
(Boss)
(Claw)
258
(Size: 5.0mm X 7.0mm)
(Note 3)
(Note 3)
258
(Size: 5.0mm X 7.0mm)
(Note 3)
(Note 3)
258
(Size: 5.0mm X 7.0mm)
(Note 3,
(Note 3,
4
)
257
(Note 2)
257
(Note 2)
257
(Note 2)
257
(Note 2)
257
(Note 2)
ns
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
ns
ns
ns
ns
ns
ns
ns
ns
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
#278
(Note 1)
(Note 1)
252
251
260
251
253
256
(Note 6)
259
(Note 5)
254
255
(Note 6)
#277
#279
#279
257
257
257
257
(Note 2)
257
(Note 2)
257
257
257
257
258
#277: M1.7 X 7.0 (Tapping)
(Silver)
4-300-113-21
4-300-113-21
1.7
7.0
#278: M2.0 X 3.0
(Pink)
4-423-712-01
4-423-712-01
3.0
2.0
#279: M1.7 X 5.0 (Tapping)
(Black)
4-423-713-01
4-423-713-01
5.0
1.7
2-9
HDR-PJ780E/PJ780VE/PJ790/PJ790E/PJ790V/PJ790VE_L2
301
1-489-963-11
SWITCH BLOCK, CONTROL (RS39900)
302
X-2584-148-1 CABINET
(F)
ASSY
303
A-1865-250-A BARRIER_UNIT,
LENS
304
A-1872-023-A LED BLOCK ASSY, ST
305
4-422-248-01
FRAME (LOWER), F
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
306
4-422-247-01
FRAME (UPPER), F
307
A-1871-872-A FR-319 BOARD, COMPLETE
308
1-885-101-11
FP-1518 FLEXIBLE BOARD
#3
2-660-401-01 SCREW(M1.7),NEW
TRU-STAR,P2
#11
3-078-890-11 SCREW,
TAPPING
#12
3-080-204-21 SCREW,
TAPPING,
P2
2-1-7. CABINET (F) SECTION
Screw
A
A B
B
C
C
#11
#11
#3
#12
#3
301
302
303
304
306
308
307
305
#3:
2.5
1.7
M1.7 X 2.5
(Red)
2-660-401-01
(Red)
2-660-401-01
#11:
4.0
1.7
M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
(Silver)
3-078-890-11
#12:
1.7
5.0
M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
(Black)
3-080-204-21
Click on the first or last page to see other HDR-PJ780E / HDR-PJ780VE / HDR-PJ790 / HDR-PJ790E / HDR-PJ790V / HDR-PJ790VE (serv.man2) service manuals if exist.