DOWNLOAD Sony HDR-PJ260 / HDR-PJ260E / HDR-PJ260V / HDR-PJ260VE / HDR-XR260V / HDR-XR260VE Service Manual ↓ Size: 6.77 MB | Pages: 28 in PDF or view online for FREE

1-6

HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2

Order

AdjustBlock

AdjustCode

Procedure

1

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the 
[SERVICE] tab.

2

Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.

3

While setting the order 1, measure with an oscilloscope the output voltage of C5526 and C5527 in 
the periphery of IC5501 on the LD-279 board to check the output voltage varies.

4

If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.

5

Turn the power OFF.

6

While measuring with an oscilloscope the output voltage of R5505 in the periphery of IC5501 on the 
LD-279 board, turn the power ON to check that the output voltage immediately after the power on 
change as shown in Fig. 2.

7

If the output voltage change as shown in Fig. 2, replace the lens block(Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-653 board 
and IC5501 of LD-279 board) periphery.

Note:  When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

AdjustBlock

AdjustCode

Procedure

1

Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SER-
VICE] tab.

2

Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.

3

While setting the order 1, measure with an oscilloscope the output voltage of C5528 and C5529 in 
the periphery of IC5501 on the LD-279 board to check the output voltage varies.

4

If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.

5

Turn the power OFF.

6

While measuring with an oscilloscope the output voltage of R5505 in the periphery
of IC5501 on the LD-279 board, turn the power ON to check that the output voltage
immediately after the power on change as shown in Fig. 2.

7

If the output voltage change as shown in Fig. 2, replace the lens block(Note).
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-653 board 
and IC5501 of LD-279 board) periphery.

Note:  When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
 

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Order

Procedure

1

Turn the power ON.

2

Confirm the connections of flexible flat cables and connectors between the lens block and LD-279 board.

3

In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of the lens 
replacement, replace LD-279 board with new one.

Note:  When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

After a part of set was replaced or after the set was assembled, check the reception of GPS signal.

Bring your camcorder to an open area, and set the GPS to ON (

 appears on the LCD screen). Your camcorder starts trying to triangulate. When 

your camcorder triangulates successfully, it will record the location information at the time movies and photos were recorded. 

• The indicator changes according to the strength of GPS signal reception.

• It may take a while before the camcorder starts triangulating.

To return the display of the unit to “A message appears asking you to confirm whether you agree with the terms of the license agreement of the map
data,” make settings according to the instructions on the SERVICE tab in the Adjustment Manual.

If you import GPS Assist Data from your computer to your camcorder using the supplied software “PlayMemories Home,” the time it takes the cam-
corder to acquire your location information can be shortened.
Connect the camcorder to a computer that is connected to the Internet. The GPS Assist Data will be updated automatically.

Do not factory check LD-279 board (PJ260/PJ260E/PJ260V/PJ260VE) in which Map Data is installed.
The Map data is erased when the factory check is done.

Do not factory check the HDD (XR260V/XR260VE) in which Map Data is installed.
The Map Data is erased when the factory check is done.

The changed portions from
Ver. 1.0 are shown in blue.

HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2

1-7E

Refer to the following flowchart when repairing or inspecting the projector’s projection function.

If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart. 
When a defective part has been clarified, repair the projector according to the check result.

Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
 

When replacing a part of the projector unit, wait until it is cooled down.

 

Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.

Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
 

Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.

Indicated defective

projector received

Measure brightness.

(  2)

Yes

No

OK

OK

NG

NG

OK

NG

A

B

Indication on 

brightness

Inspect projector

LED. 

(  1)

  1  Refer to the ADJUST tab of Adjust Manual.
  2  Refer to the SERVICE tab of Adjust Manual.

Inspect projector

LED. 

(  1)

END

-
-
-

-

-

Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)

Projector Data Input

Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40

Syywwnnnnn 

Enter the red part.

Yes

No

OK

NG

OK

NG

OK

NG

A

B

Indicated defective

projector received

Measure brightness.

(  2)

Measure brightness.

(  2)

Indication on 

brightness

Inspect projector

LED. 

(  1)

  1  Refer to the ADJUST tab of Adjust Manual.
  2  Refer to the SERVICE tab of Adjust Manual.

END

-
-
-

-

-

Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)

Projector Data Input

Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40

Syywwnnnnn 

Enter the red part.

The changed portions from
Ver. 1.0 are shown in blue.

2-1

HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2

Follow the disassembly in the numerical order given.

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original 

one.

•  Items marked “*” are not stocked since they are seldom required for routine service. 

Some delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not sup-

plied.

•  Due to standardization, replacements in the parts list may be different from the parts 

specified in the diagrams or the components used on the set.

• CAPACITORS:
 uF: 

μF

• COILS
 uH: 

μH

• RESISTORS
  All resistors are in ohms.
  METAL: metal-film resistor
  METAL OXIDE: Metal Oxide-film resistor
 F: 

nonflammable

• SEMICONDUCTORS
  In each case, u: μ, for example:
 uA...: 

μA... , uPA... , μPA... ,

 uPB... 

, 

μPB... , μPC... , μPC... ,

 uPD..., 

μPD...

The components identified by mark 0 

or dotted line with mark 0 are critical for 

safety.
Replace only with part number specified.
Les composants identifiés par une marque 
0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant 
le numéro spécifié.

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver)  : Parts Color

 

Right View

Left View

Front View

Bottom View

Top View

Back View

• Abbreviation
 AUS : 

Australian 

model

  BR   : Brazilian model
 CH  : 

Chinese 

model

 CND : 

Canadian 

model

  HK 

: Hong Kong model

 JE  : 

Tourist 

model

 KR  : 

Korea 

model

  NE 

: North European model

PJ260

HDD Model

Non HDD Model

Projector Type
Non Projector Type

• CM-123 Board
• LD-279 Board
• VC-653 Board
• ST-248 Board
• FP-1313 Flexible Board
• FP-1488 Flexible Board

• GP-037 Board
• PD-459 Board
• PJ-104 Board
• FP-1319 Flexible Board
• FP-1320 Flexible Board
• FP-1326 Flexible Board
• FP-1352 Flexible Board

• GP-037 Board
• PD-459 Board
• FP-1320 Flexible Board
• FP-1325 Flexible Board
• FP-1352 Flexible Board

• MS-478 Board
• FP-1321 Flexible Board (HDD model)
• FP-1323 Flexible Board (Non HDD model)

Control Switch Block 
(PS38100/PS38900)

PJ260E

PJ260V

PJ260VE

XR260E

XR260V

XR260VE

2-2

HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2

•  Make sure that the flat cable and flexible board are not cracked of 

bent at the terminal.

  Do not insert the cable insufficiently nor crookedly.

•  When remove a connector, don’t pull at wire of connector. It is possible 

that a wire is snapped.

•  When installing a connector, don’t press down at wire of connector. 
  It is possible that a wire is snapped.

•  Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)