Sony HDR-PJ260 / HDR-PJ260E / HDR-PJ260V / HDR-PJ260VE / HDR-XR260V / HDR-XR260VE Service Manual ▷ View online
2-7
HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2
2-1-5. OVERALL SECTION-2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
201
4-274-987-01
TAPE (AS 1/2) (C)
#1
2-635-562-11 SCREW
(M1.7)
#2
2-635-562-31 SCREW
(M1.7)
#3
2-660-401-01
SCREW (M1.7), NEW TRU-STAR, P2
1. Remove in numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
Right View
Top View
#2
#1
1
#3 X 3 → #2 X 2
Right View
Top View
#3
#2
2
#2 X 1 → #1 X 2
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#3: M1.7 X 2.5
(Red)
2-660-401-01
2-660-401-01
2.5
1.7
Note
Note: Refer to "Assembly-2: Installation Cautions of the Front
Panel Section.".
HDD Model
Non HDD Model
Projector Model
Non Projector Model
#2
#2
#3
#3
1
Battery Panel Section
(See page 2-10)
3
Cabinet (R) Section
2
Front Section
(See page 2-9)
(Note)
#3
#3
#3
#2
#1
Lens Section
(See page 2-8)
201
(See page 2-11)
Right View
Right View
Front View
Bottom View
#3
#3
#3
#2
3
#3 X 3 → #2 X 1
2-8
HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2
251
4-271-726-01
HEAT SINK (L) (380)
252
4-271-725-01
FRAME (L) (380), LENS
253
A-1851-196-A CM-123 BOARD, COMPLETE
(including CP001 (CMOS Imager)) (Note 1)
254
4-268-482-01
RUBBER (1450), SEAL
255
1-856-163-21
OPTICAL FILTER BLOCK (Note 2)
256
1-884-929-21
FP-1488 FLEXIBLE BOARD
257
4-408-191-01
SHEET (CM (385)), SHIELD
258
A-1781-268-A SERVICE,
LSV-1450A
259
4-276-408-01
SHEET (FPC (LENS))
260
A-1861-124-A VC-653 BOARD, COMPLETE (SERVICE) (HDD Model)
260
A-1861-125-A VC-653 BOARD, COMPLETE (SERVICE)
(Non HDD Model)
261
4-286-711-01
SHEET (AV), RADIATION (HDD Model) (Note 3)
262
A-1851-201-A LD-279 BOARD, COMPLETE
(XR260E/XR260V/XR260VE)
262
A-1851-202-A LD-279 BOARD, COMPLETE (PJ260/PJ260E)
262
A-1862-433-A LD-279 BOARD, COMPLETE (SERVICE)
(PJ260V/PJ260VE)
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
263
4-271-964-01
FRAME (R), LENS
264
4-271-965-01
HEAT SINK (R)
265
4-271-967-01
SHEET, CM RADIATION (Note 3)
266
4-271-968-01
SHEET (HEAT SINK R)
267
4-271-969-01
SHEET (FRAME R)
268
1-882-736-21
FP-1313 FLEXIBLE BOARD
269
4-272-050-01
SHEET (MM), SHIELD
270
4-279-796-01 GASKET
(TOP)
271
4-282-564-01 SHEET
(KZ)
272
4-279-575-01
PLATE (FRAME R), GROUND
#3
2-660-401-01
SCREW (M1.7), NEW TRU-STAR, P2
#12
3-080-204-21 SCREW,
TAPPING,
P2
#172
2-178-410-01
TITE (UB TITE) 1.4
2-1-6. LENS SECTION
LD-279
VC-6
53
HDD Model
#12
#3
257
255
(Note 2)
#172
254
256
#3
#3
#3
1
262
2
260
3
258
259
264
3
-2
263
3
-2
251
3
-3
267
266
252
3
-3
265
(Note 3)
3
-1
268
269
271
272
270
261
(Note 3)
253
(including CP001
(CMOS imager))
(Note 1)
(CMOS imager))
(Note 1)
1. Remove in numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
1
#3 X 2
Bottom View
#3
Screw
#3: M1.7 X 2.5
(Red)
2-660-401-01
2-660-401-01
2.5
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
#172: M1.4 X 4.0 (Tapping)
(Black)
2-178-410-01
2-178-410-01
1.4
4.0
2
#3 X 2
Bottom View
#3
3
CM Radiation Sheet (
3
-1
) → #3 X 3 → Heat Sink (R)/ Lens Frame (R) (
3
-2
) → #12 X 2 →
Heat Sink (L)(380)/ Lens Frame (L)(380) (
3
-3
)
Bottom View
Left View
Top View
#3
#3
#12
Note
Note 2: Refer to "Assembly-3: How to distinguish the side of Optical
Filter Block facing to Lens Device".
Note 1: Be sure to read "Precautions for Replacement of Imager" on
page 6-1 of Level 3 when changing the imager.
Note 3: Do not reuse the CM Radiation Sheetand Radiation Sheet
(AV) because their adhesive force decreases when they are
removed once.
removed once.
2-9
HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2
301
4-271-656-01
RING (380), LENS
302
A-1823-900-A CABINET (F) ASSY (380), SERVICE
303
4-271-657-01
PLATE (UPPER), LENS RING GROUND
304
4-271-948-01
EMBLEM (4.4), G
305
4-271-649-01 CUSHION,
MICROPHONE
306
4-275-996-01
CUSHION (BM), MICROPHONE
307
4-271-643-01 RETAINER,
MICROPHONE
308
4-269-133-01
COVER (A) (Note 1)
309
4-269-134-01
COVER (B) (Note 1)
310
4-269-131-01 BASE
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
311
1-471-579-11
MAGNET (Note 2)
312
4-269-135-01
YOKE, COIL (Note 2)
313
1-457-901-12
COIL (Note 2)
314
4-269-132-01 RING
315
4-269-227-01
YOKE (Note 2)
316
4-271-659-01
RETAINER (380), BARRIER
MIC901 1-542-856-11 MICROPHONE
UNIT
#1
2-635-562-11 SCREW
(M1.7)
#11
3-078-890-11 SCREW,
TAPPING
#12
3-080-204-21 SCREW,
TAPPING,
P2
2-1-7. FRONT PANEL SECTION
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
3-078-890-11
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
MIC901
#11
#1
302
301
306
307
305
304
303
#12
315
(Note 2)
314
316
313
(Note 2)
312
(Note 2)
311
(Note 2)
310
309
(Note 1)
309
(Note 1)
308
(Note 1)
308
(Note 1)
Note
Note 2: Refer to "Assembly-9: The Method of attachment of Barrier
Motor.".
Note 1: Refer to "Assembly-8: The Method of attachment of Cover
(A), Cover (B).".
The changed portions from
Ver. 1.3 are shown in blue.
Ver. 1.3 are shown in blue.
Ver. 1.4 2012.09
2-10
HDR-PJ260/PJ260E/PJ260V/PJ260VE/XR260E/XR260V/XR260VE_L2
351
4-271-957-01
HOLDER (O (381)), JACK (Non HDD Model)
352
4-277-792-01
SHEET (AVR (381)), SHIELD (Non HDD Model)
353
A-1810-661-A FP-1323 FLEXIBLE BOARD, COMPLETE
(Non HDD Model)
354
4-271-958-01
HOLDER (U (381)), JACK (Non HDD Model) (Note 2)
356
4-274-130-01
SHEET (BT), SHIELD
357
A-1852-720-A MS-478 BOARD, COMPLETE (SERVICE)
358
4-265-547-01
GASKET UA (Non HDD Model)
359
4-271-962-01 GASKET
(MS)
360
4-265-602-01 FRAME,
BT
361
4-265-603-01 PANEL,
BT
362
4-265-606-01
SPRING, BT LOCK
363
4-265-605-01 LOCK,
BT
364
4-265-609-01
CLAW, BT RETAINER
365
4-265-610-01 TALLY,
MS
366
4-265-604-01 SLOT,
MS
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
367
4-265-611-01
PLATE (MS), GROUND
368
4-298-888-01
COVER (378), MS
369
4-265-607-02 LID,
MS
370
4-271-950-01
HOLDER (O (389)), JACK (HDD Model) (Note 2)
371
A-1810-660-A FP-1321 BOARD, COMPLETE (HDD Model)
372
4-271-951-01
HOLDER (U (389)), JACK (HDD Model)
BH8001 1-251-928-21
HOLDER, BATTERY (Note 1)
BT8001 1-756-135-31
BATTERY LITHIUM SECONDARY (Note 1)
J901
1-842-658-31
JACK, DC (Non HDD Model)
J901
1-842-658-41
JACK, DC (HDD Model)
#1
2-635-562-11 SCREW
(M1.7)
#3
2-660-401-01
SCREW (M1.7), NEW TRU-STAR, P2
#11
3-078-890-11 SCREW,
TAPPING
#12
3-080-204-21 SCREW,
TAPPING,
P2
2-1-8. BATTERY PANEL SECTION
ns : not supplied
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#3: M1.7 X 2.5
(Red)
2-660-401-01
2-660-401-01
2.5
1.7
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
3-078-890-11
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
Note
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Note 1: Replace the battery holder (BH8001) together when replac-
ing the lithium storage battery (BT8001) on the MS-478
board. (The battery holder removed once
cannot be used again.)
board. (The battery holder removed once
cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
and attach new lithium storage battery next.
Note 2: Refer to "Assembly-5: Installation Cautions of the DC Jack
Harness".
MS-478
Non HDD Model
Non HDD
Model
Model
HDD Model
BH8001
(Note 1)
(Note 1)
J901
J901
ns
#1
#3
357
351
354
(Note 2)
360
361
365
358
359
364
366
362
363
368
369
367
#11
#12
353
352
356
BT8001
(Note 1)
(Note 1)
370
372
(Note 2)
#11
371
356
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.05
Click on the first or last page to see other HDR-PJ260 / HDR-PJ260E / HDR-PJ260V / HDR-PJ260VE / HDR-XR260V / HDR-XR260VE service manuals if exist.