Sony HDR-HC9 / HDR-HC9E (serv.man4) Service Manual ▷ View online
6-72
HDR-HC9/HC9E_ADJ
3.
Error Rate Check (VC-500 board)
RadarW
RadarW
RadarW
Note:
Check that the data of page: 0, address: 10 is “00”.
3-1. Preparations before adjustments
Mode
Camera recording (CAMERA-TAPE mode)
Subject
Arbitrary
Switch setting
1) REC FORMAT (Menu setting) ......................................... DV
1) REC FORMAT (Menu setting) ......................................... DV
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
71
01
Press PAUSE (Write) button.
3
0
10
01
4
C
0D
C8
Press PAUSE (Write) button.
(1C)
5
0
10
00
6
Record the camera signal for
2 minutes.
2 minutes.
3-2. Error Rate Check
Mode
VTR playback (PLAY/EDIT mode)
Subject
Recorded signal at “Preparations
before adjustments”
before adjustments”
Measurement Point
Displayed data of page: 3, address:
03
03
Measuring Instrument
Adjusting remote commander
Adjustment Page
0C
Adjustment Address
B2 to C7
Specified value
The data of page: 3, address: 03 is
“00”
“00”
Note 1:
If reading/writing data on pages 0C, set data: 01 to page:
0, address: 10, and then select pages: C. By this data set-
ting, the pages 0C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: C. By this data set-
ting, the pages 0C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Initial Value of Page 0C: Address: B2 to C7
Address
Initial
Address
Initial
Address
Initial
value
value
value
B2
00
BA
00
C2
80
B3
00
BB
00
C3
00
B4
00
BC
00
C4
00
B5
00
BD
00
C5
00
B6
00
BE
00
C6
00
B7
80
BF
00
C7
00
B8
00
C0
00
B9
00
C1
00
Table 6-3-5
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
71
01
Press PAUSE (Write) button.
3
Check that the data of page:
1C, address: B2 to C7 is the
initial value. (See Table 6-3-
5)
1C, address: B2 to C7 is the
initial value. (See Table 6-3-
5)
4
Playback the recorded signal
at “Preparations before
adjustments”.
at “Preparations before
adjustments”.
5
3
03
FF
6
3
01
40
Press PAUSE (Write) button.
7
Wait for 5 seconds.
8
3
02
Check the data changes to
“00”.
“00”.
9
3
03
Check the data is “00”. (Note 2)
10
3
01
00
Press PAUSE (Write) button.
11
Perform “Processing after
Completing Adjustments”.
Completing Adjustments”.
Note 2:
If the data is other than “00”, Error rate is abnormal.
For the contents of the abnormality, see the following
table.
For the contents of the abnormality, see the following
table.
Data of page: 3,
Contents of defect
address: 03
01
EVEN channel is abnormal.
02
ODD channel is abnormal.
03
EVEN channel and ODD channel are
abnormal.
abnormal.
Note 3:
If Error rate is abnormal, Check the use tape, clean the
tape running surface. And after inputting initial values to
page 1C: address: B3 to C8, perform re-adjustment. (See
Table 6-3-5)
tape running surface. And after inputting initial values to
page 1C: address: B3 to C8, perform re-adjustment. (See
Table 6-3-5)
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
01
3
C
0D
00
Press PAUSE (Write) button.
(1C)
4
0
10
00
5
3
70
10
Press PAUSE (Write) button.
6
3
70
Check the data changes to
“11”.
“11”.
7
0
01
00
6-73
HDR-HC9/HC9E_ADJ
1-2. S VIDEO OUT Y Level Adjustment (VC-500 board)
Mode
PLAY/EDIT
Signal
No signal
Measurement Point
Y signal terminal of S VIDEO plug
of A/V OUT jack (75
of A/V OUT jack (75
Ω terminated)
Measuring Instrument
Oscilloscope
Adjustment Page
C
Adjustment Address
25 (NTSC)
85 (PAL)
85 (PAL)
Specified value
A = 1000
± 14 mVp-p
Adjusting method:
Order Page Address Data
Procedure
1
Perform “Preparations”.
2
C
Change the data and set the Y
signal level (A) to the
specified value.
signal level (A) to the
specified value.
3
C
Press PAUSE (Write) button.
4
Perform “Processing after
Complete Adjustment”.
Complete Adjustment”.
Fig. 6-3-3
3-4.
VIDEO SYSTEM ADJUSTMENTS
Before perform the video system adjustments, check that the speci-
fied values of “Origin Oscillation Check” of “1-3. CAMERA SYS-
TEM ADJUSTMENTS” is satisfied.
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
fied values of “Origin Oscillation Check” of “1-3. CAMERA SYS-
TEM ADJUSTMENTS” is satisfied.
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
Adjusting Procedure:
1. S VIDEO OUT Y level adjustment
2. S VIDEO OUT chroma level adjustment
3. VIDEO OUT level check
4. COMPONENT OUT Y level adjustment
5. COMPONENT OUT Pr level adjustment
6. COMPONENT OUT Pb level adjustment
1. S VIDEO OUT Y level adjustment
2. S VIDEO OUT chroma level adjustment
3. VIDEO OUT level check
4. COMPONENT OUT Y level adjustment
5. COMPONENT OUT Pr level adjustment
6. COMPONENT OUT Pb level adjustment
1.
S VIDEO, VIDEO OUT Adjustment
1-1. Preparations
Perform the following data setting before the “S VIDEO, VIDEO
OUT Adjustment”.
OUT Adjustment”.
Order Page Address Data
Procedure
1
Set the unit to PLAY/EDIT
mode.
mode.
2
0
01
01
3
3
71
01
Press PAUSE (Write) button.
4
0
10
01
5
8
00
01
Press PAUSE (Write) button.
(18)
6
8
01
60
Press PAUSE (Write) button.
(18)
7
C
0F
10
Press PAUSE (Write) button.
(1C)
8
8
06
55
Press PAUSE (Write) button.
(18)
9
8
04
C0
Press PAUSE (Write) button.
(18)
10
0
10
00
11
0
FF
3E
12
B
00
02
13
C
85
Check the data is “55”.
14
0
FF
00
H
A
(NTSC)
25
(PAL)
85
(NTSC)
25
(PAL)
85
6-74
HDR-HC9/HC9E_ADJ
1-3. S VIDEO OUT Chroma Level Adjustment
(VC-500 board)
Mode
PLAY/EDIT
Signal
No signal
Measurement Point
Chroma signal terminal of S VIDEO
plug of A/V OUT jack
(75
plug of A/V OUT jack
(75
Ω terminated)
External trigger: Y signal terminal of
S VIDEO plug of A/V OUT jack
(75
S VIDEO plug of A/V OUT jack
(75
Ω terminated)
Measuring Instrument
Oscilloscope
Adjustment Page
C
Adjustment Address
26, 27 (NTSC)
86, 87 (PAL)
86, 87 (PAL)
Specified value
Cr level: A = 714
± 14 mVp-p(NTSC)
A = 700
± 14 mVp-p(PAL)
Cb level: B = 714
± 14 mVp-p(NTSC)
B = 700
± 14 mVp-p(PAL)
Burst level: C = 286
± 6 mVp-p(NTSC)
C = 300
± 6 mVp-p(PAL)
Adjusting method:
Order Page Address Data
Procedure
1
Peform “Preparations”.
2
C
Change the data and set the
Cr signal level (A) to the
specified value.
Cr signal level (A) to the
specified value.
3
C
Press PAUSE (Write) button.
4
C
Change the data and set the
Cb signal level (B) to the
specified value.
Cb signal level (B) to the
specified value.
5
C
Press PAUSE (Write) button.
6
Check the burst signal (C) to
the specified value.
the specified value.
7
Perform “Processing after
Complete Adjustment”.
Complete Adjustment”.
H
A
0.28
µ
sec (NTSC)
B
0.28
µ
sec (NTSC)
0.23
µ
sec (PAL)
0.23
µ
sec (PAL)
C
Fig. 6-3-4
(NTSC)
26
(PAL)
86
(NTSC)
26
(PAL)
86
(NTSC)
27
(PAL)
87
(NTSC)
27
(PAL)
87
6-75
HDR-HC9/HC9E_ADJ
1-5. Processing after Complete Adjustment
Perform the setting through the procedure mentioned below when
you finish the “S VIDEO, VIDEO OUT Adjustment”.
you finish the “S VIDEO, VIDEO OUT Adjustment”.
Order Page Address Data
Procedure
1
0
10
01
2
C
0F
00
Press PAUSE (Write) button.
(1C)
3
8
04
80
Press PAUSE (Write) button.
(18)
4
8
00
00
Press PAUSE (Write) button.
(18)
5
8
01
00
Press PAUSE (Write) button.
(18)
6
8
06
00
Press PAUSE (Write) button.
(18)
7
0
10
00
8
3
70
10
Press PAUSE (Write) button.
9
3
70
Check the data changes to
“11”.
“11”.
10
0
01
00
1-4. VIDEO OUT Level Check (VC-500 board)
Mode
PLAY/EDIT
Signal
No signal
Measurement Point
Video terminal of A/V OUT jack
(75
(75
Ω terminated)
Measuring Instrument
Oscilloscope
Specified value
Sync level: A = 286
± 18 mVp-p(NTSC)
A = 300
± 18 mVp-p(PAL)
Burst level: B = 286
± 18 mVp-p(NTSC)
B = 300
± 18 mVp-p(PAL)
Checking method:
Order Page Address Data
Procedure
1
Peform “Preparations”
2
Check the sync signal level
(A) to the specified value.
(A) to the specified value.
3
Check the burst signal level
(B) to the specified value.
(B) to the specified value.
4
Perform “Processing after
Complete Adjustment”.
Complete Adjustment”.
Fig. 6-3-5
H
B
A
Click on the first or last page to see other HDR-HC9 / HDR-HC9E (serv.man4) service manuals if exist.