Sony HDR-HC9 / HDR-HC9E (serv.man2) Service Manual ▷ View online
1-6
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-HC9/HC9E_L2
1-7-2. E : 62 : 10 [Shift Lens Initializing Failure] Occurred
Connect the adjustment remote commander (RM-95 or NEW LANC JIG) and perform the following process.
Order Page Address Data
Procedure
1
0
01
01
2
0
10
07
3
F
06
Read the data value and assume it as D
06
.
(7F)
4
F
06
Change the data and check that it has been changed. If no value changes or if value is 00 or FF, inspect
(7F)
the EEPROM (IC1802 of VC-500 board). If value changes, proceed to the order 5.
5
F
06
D
06
Press PAUSE (Write) button.
(7F)
6
F
07
Read the data value and assume it as D
07
.
(7F)
7
F
07
Change the data and check that it has been changed. If no value changes or if value is 00 or FF, inspect
(7F)
the EEPROM (IC1802 of VC-500 board). If value changes, proceed to the order 8.
8
F
07
D
07
Press PAUSE (Write) button.
(7F)
9
0
10
00
10
0
01
00
Perform “Hall Adjustment”. (Note 1)
11
If the lens does not move at all when adjusting it, proceed to the order 12. When the adjustment ends,
proceed to the order 16. (Note 1)
proceed to the order 16. (Note 1)
12
2
01
2D
Press PAUSE (Write) button.
13
2
02
Read the data value. If value is not 01, inspect the EEPROM (IC1802 of VC-500 board). When value
is 01, proceed to the order 14.
is 01, proceed to the order 14.
14
2
01
00
Press PAUSE (Write) button.
15
Turn the power OFF and ON again.
16
Check that no error occurs. If an error occurs, replace the lens block (Note 2).
Note 1: Perform adjustment by referring to “Hall Adjustment” in Service Manual, ADJ. After the adjustment, be sure to perform
“Angular Velocity Sensor Sensitivity Adjustment”.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-7
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-HC9/HC9E_L2
1-7-3. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Connect the adjustment remote commander (RM-95 or NEW LANC JIG) and perform the following process.
Order Page Address Data
Procedure
1
0
01
01
2
0
10
06
3
B
B2
01
Press PAUSE (Write) button.
(6B)
4
0
10
07
5
D
46
F0
Press PAUSE (Write) button.
(7D)
6
D
48
01
Press PAUSE (Write) button. (Note 1)
(7D)
7
D
48
00
Press PAUSE (Write) button.
(7D)
8
D
46
10
Press PAUSE (Write) button.
(7D)
9
D
48
01
Press PAUSE (Write) button. (Note 1)
(7D)
10
D
48
00
Press PAUSE (Write) button.
(7D)
11
0
10
06
12
B
B2
00
Press PAUSE (Write) button.
(6B)
13
0
10
00
14
0
01
00
15
Check if the shift lens moves while setting the order 5 to 10. If the shift lens does not move, replace the
lens block (Note 2). When the shift lens moved, proceed to the order 16.
lens block (Note 2). When the shift lens moved, proceed to the order 16.
16
While setting the order 5 to 10, measure with an oscilloscope the output voltage of R5721 in the periphery
of IC5703 on the LD-221 board to check the output voltage varies.
of IC5703 on the LD-221 board to check the output voltage varies.
17
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied,
proceed to the order 18.
proceed to the order 18.
18
Turn the power OFF.
19
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the
LD-221 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
LD-221 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
20
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not change as
shown in Fig. 2, inspect the camera control circuit (IC1801 of VC-500 board) periphery.
shown in Fig. 2, inspect the camera control circuit (IC1801 of VC-500 board) periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set page: D (7D), address: 48, data:
00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-8
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-HC9/HC9E_L2
1-7-4. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect the adjustment remote commander (RM-95 or NEW LANC JIG) and perform the following process.
Order Page Address Data
Procedure
1
0
01
01
2
0
10
06
3
B
B2
01
Press PAUSE (Write) button.
(6B)
4
0
10
07
5
D
47
F0
Press PAUSE (Write) button.
(7D)
6
D
49
01
Press PAUSE (Write) button. (Note 1)
(7D)
7
D
49
00
Press PAUSE (Write) button.
(7D)
8
D
47
10
Press PAUSE (Write) button.
(7D)
9
D
49
01
Press PAUSE (Write) button. (Note 1)
(7D)
10
D
49
00
Press PAUSE (Write) button.
(7D)
11
0
10
06
12
B
B2
00
Press PAUSE (Write) button.
(6B)
13
0
10
00
14
0
01
00
15
Check if the shift lens moves while setting the order 5 to 10. If the shift lens does not move, replace the
lens block (Note 2). When the shift lens moved, proceed to the order 16.
lens block (Note 2). When the shift lens moved, proceed to the order 16.
16
While setting the order 5 to 10, measure with an oscilloscope the output voltage of R5737 in the periphery
of IC5703 on the LD-221 board to check the output voltage varies.
of IC5703 on the LD-221 board to check the output voltage varies.
17
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied,
proceed to the order 18.
proceed to the order 18.
18
Turn the power OFF.
19
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the
LD-221 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
LD-221 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
20
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not change as
shown in Fig. 2, inspect the camera control circuit (IC1801 of VC-500 board) periphery.
shown in Fig. 2, inspect the camera control circuit (IC1801 of VC-500 board) periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set page: D (7D), address: 49, data:
00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-7-5. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Check that R1823 in the periphery of IC1801 on the VC-500 board is 0
Ω and energizes. If it is not energizes, replace the R1823.
When R1823 is 0
Ω and energizes, replace the lens block (Note).
3
Check that no error occurs, after replacing the lens block and performing the necessary adjustment. If an error occurs, inspect
the camera control circuit (IC1801 of VC-500 board) periphery.
the camera control circuit (IC1801 of VC-500 board) periphery.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-9
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-HC9/HC9E_L2
1. SERVICE NOTE
1-2. イジェクトしない時のカセット取出し方法（強制イジェクト）
1
2.
DISASSEMBLYを参照し，メカデッキを外す。
2
カセコン組立を押さえながら，安定化電源より＋4.5Vをローディングモータに加え，アンローディングさせる。
ローディングモータ
安定化電源（+4.5Vdc）
1-3. 強制電源ONモードの設定
調整リモコン（RM-95またはNEW
LANC
JIG）を使用して，電源を入れることが出来ます。
VTR操作は調整リモコンで行えます。
1-3-1. 強制カメラ電源ONモードの設定
1) ページ：0，アドレス：01にデータ：01をセット。
2) ページ：A，アドレス：10にデータ：01をセットしPAUSE（Write）ボタンを押す。
1-3-2. 強制VTR電源ONモードの設定
1) ページ：0，アドレス：01にデータ：01をセット。
2) ページ：A，アドレス：10にデータ：02をセットしPAUSE（Write）ボタンを押す。
1-3-3. 強制電源ONモードの解除
1) ページ：0，アドレス：01にデータ：01をセット。
2) ページ：A，アドレス：10にデータ：00をセットしPAUSE（Write）ボタンを押す。
3) ページ：0，アドレス：01にデータ：00をセット。
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200B）を使用する。）
Click on the first or last page to see other HDR-HC9 / HDR-HC9E (serv.man2) service manuals if exist.