Sony HDR-FX1 / HDR-FX1E (serv.man3) Service Manual ▷ View online
6-10
HDR-FX1/FX1E
2. Modification of 8, C, 13, 18, 1C Page Data
If the 8, C, 13, 18, 1C page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
If the 8, C, 13, 18, 1C page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
When changing the 8, C page data, select page: 0, address: 10,
and set data: 00.
and set data: 00.
3)
When changing the 13, 18, 1C page data, select page: 0, address:
10, and set data: 01.
After completing the modification of 13, 18, 1C page data,
reset the data of this address to “00”.
10, and set data: 01.
After completing the modification of 13, 18, 1C page data,
reset the data of this address to “00”.
4)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
5)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
6)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of 8, C, 13, 18, 1C Page data
Order Page Address Data
Procedure
1
0
10
00
Set the data.
2
2
00
29
Set the data.
3
2
01
29
Set the data, and press PAUSE
button.
button.
Version check of the mechanism control microprocessor:
(VC-367 board IC8801)
(VC-367 board IC8801)
Order Page Address Data
Procedure
1
0
10
00
Set the data.
2
3
FF
The data shows the version of
the mechanism control
microprocessor.
10: Ver. 1.0 (MP1)
20: Ver. 2.0 (MP2)
the mechanism control
microprocessor.
10: Ver. 1.0 (MP1)
20: Ver. 2.0 (MP2)
Note:
For PAL model, the S VIDEO OUT Y/chroma level adjustment
addresses are changed by the version of the mechanism control
microprocessor. (Refer to “4. C Page Table”.)
addresses are changed by the version of the mechanism control
microprocessor. (Refer to “4. C Page Table”.)
1-2-2.
INITIALIZATION OF 8, C, 13, 18, 1C PAGE DATA
Note1: When reading or writing the 8, C page data, select page: 0, address:
10, and set data: 00.
When reading or writing the 13, 18, 1C page data, select page: 0,
address: 10, and set data: 01, then select 3, 8 or C page. The 13, 18
or 1C page can be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
When reading or writing the 13, 18, 1C page data, select page: 0,
address: 10, and set data: 01, then select 3, 8 or C page. The 13, 18
or 1C page can be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2: NTSC model: HDR-FX1
PAL model: HDR-FX1E
1. Initializing the 8, C, 13, 18, 1C Page Data
Note1: If “Initializing the 8, C, 13, 18, 1C Page Data” is performed, all
data of the 8 page, C page, 13 page, 18 page and 1C page will be
initialized. (It is impossible to initialize a single page.)
initialized. (It is impossible to initialize a single page.)
Note2: If the 8, C, 13, 18, 1C page data has been initialized, following
adjustments need to be performed again.
1) Modification of 8, C, 13, 18, 1C page data
2) Viewfinder system adjustments
3) LCD system adjustments
4) Serial No. input
5) Servo and RF system adjustments
6) Video system adjustments
1) Modification of 8, C, 13, 18, 1C page data
2) Viewfinder system adjustments
3) LCD system adjustments
4) Serial No. input
5) Servo and RF system adjustments
6) Video system adjustments
Note3: NTSC model: HDR-FX1
PAL model: HDR-FX1E
Adjusting page
8
Adjusting Address
00 to FF
Adjusting page
C
Adjusting Address
10 to FF
Adjusting page
13
Adjusting Address
00 to FF
Adjusting page
18
Adjusting Address
00 to FF
Adjusting page
1C
Adjusting Address
00 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
0
10
00
Set the data.
3
3
81
00
Set the data.
4
3
80
0C
Set the data, and press PAUSE
button.
button.
5
3
80
Check that the data changes to
“1C”.
“1C”.
6
Perform “Modification of 8, C,
13, 18, 1C Page Data”.
13, 18, 1C Page Data”.
6-11
HDR-FX1/FX1E
3. 8 Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
13, 18, 1C Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Address
00 to 7D
7E
7F to 83
84
85 to 9C
9D
9E
9F
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A1
A2
A3
A4
A5
A6
A7
A8
A9 to AC
AD
AE to B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BB
BC
BD
BE to BF
C0
C1
C2
C3
C4
C5
C1
C2
C3
C4
C5
C6 to C7
C8
C9
C9
CA
CB
CC
CD
CB
CC
CD
CE
CF
D0
D1
D2
D3
CF
D0
D1
D2
D3
D4 to FF
Remark
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Table. 6-1-6.
4. C Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
13, 18, 1C Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Note3: PAL model with the version 1.0 mechanism control
microprocessor, or NTSC model.
Note4: PAL model with the version 2.0 mechanism control
microprocessor. (Refer to “2. Modification of 8, C, 13, 18, 1C
Page Data” for version check of the mechanism control
microprocessor (VC-367 board IC8801).).
Page Data” for version check of the mechanism control
microprocessor (VC-367 board IC8801).).
Initial value
NTSC PAL
00 to 0F
10
11
12
13
14 to 15
16
17 to 24
25
26
27
28 to 30
32
33
34
35
36
37
38
39
3A
3B
3C
3D to 44
45
46
47
48
49 to 4A
4B
4C
4D
4D to 50
51
52
53
54
55 to 68
69
6A
6B to 6D
6E
6F
70
71
Switching position adj.
Fixed data-1
CAP FG duty adj.
Fixed data-1
S VIDEO out Y level adj. (Note3)
S VIDEO out chroma level adj.
(Note3)
Fixed data-1
Backlight adj. (EVF)
VCO adj. (EVF)
VCOM level adj. (EVF)
RGB AMP adj. (EVF)
Fixed data-1
PSIG level adj. (EVF)
White balance adj. (EVF)
Contrast adj. (EVF)
Fixed data-1
VCO adj. (LCD)
V COM adj. (LCD)
RGB AMP adj. (LCD)
Fixed data-1
Transmissive mode white balance
adj. (LCD)
Contrast adj. (SD) (LCD)
Fixed data-1
Fixed data-2
Fixed data-1
Sample hold phase adj. (LCD)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Reflective mode white balance adj.
(LCD)
Address
Remark
Initial value
EE
00
00
00
E0
70
2A
2A
53
9D
30
59
2A
8E
4E
80
80
18
80
80
9A
88
80
80
31
7F
80
80
EE
00
00
00
E0
70
2A
2A
53
9D
30
59
2A
8E
4E
80
80
18
80
80
9A
88
80
80
31
7F
80
80
6-12
HDR-FX1/FX1E
Initial value
NTSC PAL
Address
Remark
Initial value
Table. 6-1-7.
5. 13 Page Table
Note1: When reading or writing the 13 page data, select page: 0, address:
10, and set data: 01, then select 8 page. The 13 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
13, 18, 1C Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Address
Remark
Initial value
Address
Remark
Initial value
00 to 0F
04
05
06
07
08
09
0A
0B
0C to 12
13
14 to 24
25
26 to FF
08
00
46
01
02
00
00
00
Serial No. input
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
C page
72
73
74 to 75
76
77
78 to 81
82
83
84
85
86
87
88 to F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
31
18
75
36
36
70
2A
2A
00
00
00
00
00
00
00
00
00
00
00
00
31
18
75
36
36
70
2A
2A
00
00
00
00
00
00
00
00
00
00
00
00
Fixed data-1
Fixed data-2
Fixed data-1
Contrast adj.(HD) (LCD)
Contrast adj. (EVF)
Fixed data-1
COMPONENT OUTPT level adj.
S VIDEO out Y level adj. (Note4)
S VIDEO out chroma level adj.
(Note4)
Fixed data-1
Emergency memory address
(Mechanism section)
Table. 6-1-8.
6. 18 Page Table
Note1: When reading or writing the 18 page data, select page: 0, address:
10, and set data: 01, then select 8 page. The 18 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
13, 18, 1C Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
13, 18, 1C Page Data”).
Table. 6-1-9.
Address
00 to 5D
5E
5F to FF
Remark
Fixed data-1
Fixed data-2
Fixed data-1
Address
Remark
Initial value
Address
Remark
Initial value
00 to 42
43
44 to 46
47
48
49
4A to 4D
4E
4F
50
51
52
53
54
55
56
57
58
59 to 5D
5E
5F to 66
67
68 to 69
6A
6B to B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
00
00
00
00
00
80
00
00
00
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Error rate check
7. 1C Page Table
Note1: When reading or writing the 1C page data, select page: 0, address:
10, and set data: 01, then select C page. The 1C page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C,
18, 1C Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
18, 1C Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of 8, C,
18, 1C Page Data”).
6-13
HDR-FX1/FX1E
1-2-3.
INITIALIZATION OF 9, 1D PAGE DATA
Note: When reading or writing the 9 page data, select page: 0, address:
10, and set data: 00.
When reading or writing the 1D page data, select page: 0, address:
10, and set data: 01, then select D page. The 1D page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
When reading or writing the 1D page data, select page: 0, address:
10, and set data: 01, then select D page. The 1D page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1. Initializing the 9, 1D Page Data
Note1: If “Initializing the 9, 1D Page Data” is performed, all data of the 9
page and 1D page will be initialized. (It is impossible to initialize
a single page.)
a single page.)
Note2: If the 9, 1D page data has been initialized, following adjustments
need to be performed again.
1) Modification of 9, 1D page data
1) Modification of 9, 1D page data
Adjusting page
9
Adjusting Address
10 to FF
Adjusting page
1D
Adjusting Address
00 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
0
10
00
Set the data.
3
3
81
00
Set the data.
4
3
80
04
Set the data, and press PAUSE
button.
button.
5
3
80
Check that the data changes to
“14”.
“14”.
6
Perform “Modification of 9, 1D
Page Data”.
Page Data”.
2. Modification of 9, 1D Page Data
If the 9, 1D page data has been initialized, change the data of the
“Fixed data-2” address shown in the following table by manual input.
If the 9, 1D page data has been initialized, change the data of the
“Fixed data-2” address shown in the following table by manual input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
When changing the 9 page data, select page: 0, address: 10,
and set data: 00.
and set data: 00.
3)
When changing the 1D page data, select page: 0, address: 10,
and set data: 01.
After completing the modification of 1D page data, reset the
data of this address to “00”.
and set data: 01.
After completing the modification of 1D page data, reset the
data of this address to “00”.
4)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
5)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
6)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of 9, 1D Page data
Order Page Address Data
Procedure
1
0
10
00
Set the data.
2
2
00
29
Set the data.
3
2
01
29
Set the data, and press PAUSE
button.
button.
Address
00 to 0F
10 to FF
Remark
Fixed data-1
Address
00 to FF
Remark
Fixed data-1
3. 9 Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 9, 1D
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 9, 1D
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of 9, 1D
Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of 9, 1D
Page Data”).
Table. 6-1-11.
4. 1D Page Table
Note1: When reading or writing the 1D page data, select page: 0, address:
10, and set data: 01, then select D page. The 1D page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2: The data of page: 0, address: 10 must be “00”.
Note3: Fixed data-1: Initialized data. (Refer to “1. Initializing the 9, 1D
Note3: Fixed data-1: Initialized data. (Refer to “1. Initializing the 9, 1D
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of 9, 1D
Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of 9, 1D
Page Data”).
Table. 6-1-12.
Address
Remark
Initial value
Address
Remark
Initial value
1C page
BC
BD
BE
BF
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9 to FB
FC
FD to FF
00
00
00
00
00
00
00
80
00
00
00
00
00
Error rate check
Fixed data-1
Fixed data-2
Fixed data-1
Table. 6-1-10.
Click on the first or last page to see other HDR-FX1 / HDR-FX1E (serv.man3) service manuals if exist.