DOWNLOAD Sony HDR-CX500 / HDR-CX500E / HDR-CX500V / HDR-CX500VE / HDR-CX505VE / HDR-CX520 / HDR-CX520E / HDR-CX520V / HDR-CX520VE (serv.man2) Service Manual ↓ Size: 6.92 MB | Pages: 99 in PDF or view online for FREE

1-22

HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2

Part No.

A-1739-017-A

Description

CABINET (BOTTOM (CX520-J1))

Serial No.

Serial No.

Part No.

A-1739-019-A

Description

CABINET (BOTTOM (CX520-U2))

Serial No.

Part No.

A-1739-020-A

Description

CABINET (BOTTOM (CX520-CA2))

* Manufacturing date

* Affix the label

* Manufacturing date

* Factory

* Affix the label

The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.

Note 1:

After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.

Note 2:

When replacing the cabinet (bottom) assy for US, affix
the “Manufacturing date” label and the “Factory” label
on the specified location as shown in the figure.
The date label and inset (how to affix) are supplied
together with the cabinet (bottom) assy.

Note 3:

When replacing the cabinet (bottom) assy for Japanese,
affix the “Manufacturing date” label on the specified
location as shown in the figure.
The date label and inset (how to affix) are supplied
together with the cabinet (bottom) assy.

(JAPANESE)
1-14. キャビネット (底) 組立交換時の注意

(HDR-CX520V)

機種の表示部はレーザー印字方式を採用しております。

この為，交換用のキャビネット  (底)  組立は仕向けにより異

なります。類似の表示もありますので，該当するものを選

んで注文して下さい。

注意1: キャビネット (底) 組立交換後はシリアルナンバー

がサービス専用のシリアルナンバーに変更されま

す。 お客様への案内と修理データのシリアルナン

バー変更を行ってください。

注意2:

US仕向けキャビネット (底) 組立を交換した際は

「製造時期」を表すラベルと，「製造所」を表す

ラベルを図の指定位置に貼り付けてください。

なお，キャビネット (底) 組立には時期表示ラベ

ル，投げ込み(ラベル貼り方)がセットで供給され

ます。

注意3:

Japanese仕向けキャビネット (底) 組立を交換した

際は，「製造時期」を表すラベルを図の指定位置

に貼り付けてください。

なお，キャビネット (底) 組立には時期表示ラベ

ル，投げ込み(ラベル貼り方)がセットで供給され

ます。

1-23E

HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2

Part No.

A-1739-022-A

Description

CABINET (BOTTOM (CX520-AU2))

Serial No.

Serial No.

Part No.

A-1739-021-A

Description

CABINET (BOTTOM (CX520-CEN))

The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.

Note 1:

After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.

(JAPANESE)
1-15. キャビネット (底) 組立交換時の注意

(HDR-CX520VE)

機種の表示部はレーザー印字方式を採用しております。

この為，交換用のキャビネット  (底)  組立は仕向けにより異

なります。類似の表示もありますので，該当するものを選

んで注文して下さい。

注意1: キャビネット (底) 組立交換後はシリアルナンバー

がサービス専用のシリアルナンバーに変更されま

す。 お客様への案内と修理データのシリアルナン

バー変更を行ってください。

2-1

HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, don’t press down at wire of connector.

It is possible that a wire is snapped.

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

The charging capacitor (C5008) of the ST-217 board is charged
up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand.  The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off.  Therefore, the
remaining voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.

1 k

Ω

/1 W

Wrap insulating tape.

R:1 k

Ω

 /1 W 

(Part code: 
  1-215-869-11)

C5008
(Charging Capacitor)

C5008

ST-217 Board

ST-217 Board

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between the two points 
with the short jig about 10 seconds.

2-2

HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2

  - GP317 Block
  - F Panel Block

  - FP-1122 Block
  - VC-575 Board Block

  - Cabinet (Bottom) Block
  - Remote Control Window
  - Cabinet (L) Assy

  - Cabinet (R) Section
  - Cabinet (Top) Block
  - BT Panel Section

   - FP-1123 Block
   - MM-083 Board Block
   - VC-575 Section

  - PD-389 Board
  - FTS Block

  - CK-217 Board Block
  - Hinge Assy

BT Panel Section

Cabinet (Bottom) Block

Cabinet (L) Assy

Front Panel Section

Cabinet (Top) Section

Lens/Main Block

 • GP317 Assy
 • ST-217 Board
 • FP-1120 Flexible Board
 • FP-1123 Flexible Board
 • FP-1126 Flexible Board
 • MM-083 Board
 • FP-1122 Flexible Board
 • VC-575 Board
 • FP-1124 Flexible Board
 • FP-1021 Flexible Board
 • CM-103 Board

Cabinet (R) Section

 • PD-389 Board
 • CK-217 Board
 • FP-1127 Flexible Board
 • FP-1128 Flexible Board