Sony HDR-CX400E / HDR-CX410VE / HDR-CX430V / HDR-CX430VE / HDR-CX510E / HDR-PJ420E / HDR-PJ420VE / HDR-PJ430 / HDR-PJ430E / HDR-PJ430V / HDR-PJ430VE / HDR-PJ510E (serv.man2) Service Manual ▷ View online
1-5
HDR-CX400E/CX410VE/CX430V/CX430VE/CX510E/PJ420E/PJ420VE/PJ430/PJ430E/PJ430V/PJ430VE/PJ510E_L2
– ENGLISH –
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
9
4
0
1
Internal flash memory fault
IM Model:
Inspect the flash memory (IC8101 on the MM-102 board).
E
9
4
0
2
BGM data error
Check the CPU (IC1301 on the VC-1012 board).
E
9
5
0
0
GPS hardware error
GPS Model:
Check whether the FFC-254 flexible flat cable is broken, and check
whether it is inserted imperfectly.
If there is no problem the flexible board, inspect or replacement of
the GP-037 board.
E
9
6
0
0
Map area mount error
GPS Model:
Inspect or replacement of the MM-102 board.
E
9
7
0
0
Projector hardware error
Turn power off and turn power on again.
1-5. METHOD OF COPING WITH SHIFT LENS ERROR
VC-1012 BOARD (SIDE A)
IC5601
C5636
C5640
C5642
C5643
R5632
Fig. 1
Measurement points on the VC-1012 board
approx. 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R5632 on the VC-1012 board
1-5-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5632 in the periphery of IC5601 on the VC-1012 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1301 of VC-1012 board) periphery.
the camera control circuit (IC1301 of VC-1012 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Order
AdjustBlock
AdjustCode
Order
1
Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the
[SERVICE] tab.
[SERVICE] tab.
2
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
3
While setting the order 1, measure with an oscilloscope the output voltage of C5642 and C5643 in
the periphery of IC5601 on the VC-1012 board to check the output voltage varies.
the periphery of IC5601 on the VC-1012 board to check the output voltage varies.
4
If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
When the output voltage varied, proceed to the order 5.
5
Turn the power OFF.
6
While measuring with an oscilloscope the output voltage of R5632 in the periphery of IC5601 on the
VC-1012 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
VC-1012 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
7
If the output voltage rises to 3V, replace the lens block (Note).
If it does not rises to 3V, inspect the camera control circuit IC1301 and IC5601 on the VC-1012
board periphery.
If it does not rises to 3V, inspect the camera control circuit IC1301 and IC5601 on the VC-1012
board periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-6
HDR-CX400E/CX410VE/CX430V/CX430VE/CX510E/PJ420E/PJ420VE/PJ430/PJ430E/PJ430V/PJ430VE/PJ510E_L2
1-5-3.E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Order
AdjustBlock
AdjustCode
Order
1
Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SER-
VICE] tab.
VICE] tab.
2
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
3
While setting the order 1, measure with an oscilloscope the output voltage of C5636 and C5640 in the
periphery of IC5601 on the VC-1012 board to check the output voltage varies.
periphery of IC5601 on the VC-1012 board to check the output voltage varies.
4
If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
When the output voltage varied, proceed to the order 5.
5
Turn the power OFF.
6
While measuring with an oscilloscope the output voltage of R5632 in the periphery
of IC5601 on the VC-1012 board, turn the power ON to check that the output voltage
immediately after the power on change as shown in Fig. 2.
of IC5601 on the VC-1012 board, turn the power ON to check that the output voltage
immediately after the power on change as shown in Fig. 2.
7
If the output voltage rises to 3V, replace the lens block (Note).
If it does not rises to 3V, inspect the camera control circuit IC1301 and IC5601 on the VC-1012 board
periphery.
If it does not rises to 3V, inspect the camera control circuit IC1301 and IC5601 on the VC-1012 board
periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Confirm the connections of flexible flat cables and connectors between the lens block and VC-1012 board.
3
In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of the lens
replacement, replace VC-1012 board with new one.
replacement, replace VC-1012 board with new one.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
– ENGLISH –
1-6. GPS RECEIVING CHECK (CX410VE/CX430V/CX430VE/PJ420VE/PJ430V/PJ430VE)
After a part of the set was replaced or after the set was assembled, check the reception of GPS signal.
How to check the GPS function
Bring your camcorder to an open area, and set the GPS to ON (
appears on the LCD screen). Your camcorder starts trying to triangulate. When
your camcorder triangulates successfully, it will record the location information at the time movies and photos were recorded.
• The indicator changes according to the strength of GPS signal reception.
• It may take a while before the camcorder starts triangulating.
To return the display of the unit to “A message appears asking you to confirm whether you agree with the terms of the license agreement of the map
data,” make settings according to the instructions on the SERVICE tab in the Adjustment Manual.
data,” make settings according to the instructions on the SERVICE tab in the Adjustment Manual.
Use GPS Assist Data
If you import GPS Assist Data from your computer to your camcorder using the supplied software “PlayMemories Home,” the time it takes the cam-
corder to acquire your location information can be shortened.
Connect the camcorder to a computer that is connected to the Internet. The GPS Assist Data will be updated automatically.
corder to acquire your location information can be shortened.
Connect the camcorder to a computer that is connected to the Internet. The GPS Assist Data will be updated automatically.
1-7. PRECAUTION ON REPLACING THE MM-102 BOARD (CX410VE/CX430V/CX430VE/
CX510E/PJ420E/PJ420VE/PJ430/PJ430E/PJ430V/PJ430VE/PJ510E)
Do not factory check MM-102 board (GPS Model) in which Map Data is installed.
The Map data is erased when the factory check is done.
The Map data is erased when the factory check is done.
1-7
HDR-CX400E/CX410VE/CX430V/CX430VE/CX510E/PJ420E/PJ420VE/PJ430/PJ430E/PJ430V/PJ430VE/PJ510E_L2
– ENGLISH –
1-8. DISCHARGE OF LED FLASH/VIDEO LIGHT
This model is provided with a flash unit using LED Flash/Video light.
Therefore, the LED Flash/Video light does not have high voltage part and does not need to be discharged.
Therefore, the LED Flash/Video light does not have high voltage part and does not need to be discharged.
1-9. NOTE ON REPLACING PROJECTOR UNIT
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart.
When a defective part has been clarified, repair the projector according to the check result.
chart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK
OK
NG
NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED.
( 1)
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
1-8
HDR-CX400E/CX410VE/CX430V/CX430VE/CX510E/PJ420E/PJ420VE/PJ430/PJ430E/PJ430V/PJ430VE/PJ510E_L2
– ENGLISH –
1-10. FRONT ORNAMENT REPLACING METHOD
Lens Cap
Note: A protective Lens Cap is attached to each new service
Lens Block.
Carry out replacement work with this Lens Cap attached.
Removal
(1) Disconnect the three connectors and peel off the Adhesive Parts
of the Motor A Flexible Board, Motor B Flexible Board, and the
FP-2126 Flexible Board.
FP-2126 Flexible Board.
TO
P
FR
ONT
Adhesive part
Adhesive part
Adhesive part
Connector
Connectors
FP-2125 Flexible
Board
Board
FP-2126 Flexible
Board
Board
Flexible Board of the Motor B
Flexible Board of
the Motor A
the Motor A
(2) Remove the seven screws and remove the Sheet Metal (C) and
the Edge of Mechanical Rubber while detaching the two bosses,
and then peel off the Adhesive Part of the FP-2125 Flexible
Board.
and then peel off the Adhesive Part of the FP-2125 Flexible
Board.
TO
P
FRONT
Screws
Screws
Mecha Stopper Rubber
Screw
Screw
Screw
Boss
Boss
Adhesive part
FP-2125
Flexible Board
Flexible Board
Sheet Metal (C)
(3) Peel off the Adhesive Part of the FP-2118 Flexible Board.
TOP
FRONT
Adhesive part
FP-2118
Flexible Board
Flexible Board
(4) Remove the five screws and remove the Frame (F-SUB-A),
Frame (F-SUB-B), and Ball Bearing while detaching the four
bosses and the shaft.
bosses and the shaft.
TO
P
FRONT
Screw
Screw
Screws
Boss
Boss
Boss
Bosses
Shaft
FP-2118 Flexible Board
Motor B
Frame (F-Sub-B),
Ball Bearing
Ball Bearing
Frame (F-Sub-A)
(5) Remove the three screws and remove the Motor B.
Screws
Motor B
FR
ONT
TOP
(6) Disconnect the connector and remove the FP-2118 Flexible
Board and the Radiation Sheet while detaching the four bosses.
FR
ONT
TOP
TOP
Bosses
Adhesive
part
part
Adhesive
part
part
Boss
FP-2118
Flexible Board
Flexible Board
FP-2118 Flexible Board
Connector
Connector
CM Radiation Sheet
(7) Remove the six screws and remove the Frame (E-SUB-A), Frame
(E-SUB-B), Ball Bearing while detaching the six bosses and the
shaft.
shaft.
FRONT
TO
P
Screws
Screws
Boss
Boss
Shaft
Hole
Frame (E-Sub-A),
Ball Bearing
Ball Bearing
Frame (E-Sub-B)
(8) Peel off the Adhesive Part of the Motor A Flexible Board while
detaching the two bosses.
Adhesive part
Flexible Board of
the Motor A
the Motor A
Bosses
FRONT
TOP
Click on the first or last page to see other HDR-CX400E / HDR-CX410VE / HDR-CX430V / HDR-CX430VE / HDR-CX510E / HDR-PJ420E / HDR-PJ420VE / HDR-PJ430 / HDR-PJ430E / HDR-PJ430V / HDR-PJ430VE / HDR-PJ510E (serv.man2) service manuals if exist.