Sony DCR-TRV60 / DCR-TRV60E / DCR-TRV70 (serv.man3) Service Manual ▷ View online
37
Recording – Basics
You can use these buttons to check the recorded picture or shoot so that the transition
between the last recorded scene and the next scene you record is smooth.
between the last recorded scene and the next scene you record is smooth.
End search
You can go to the end of the recorded section after you record.
(1) Set the POWER switch to CAMERA.
(2) Press FN to display PAGE1.
(3) Press END SCH.
(2) Press FN to display PAGE1.
(3) Press END SCH.
The last five seconds of the recorded section is played back and your
camcorder returns to standby.
camcorder returns to standby.
To return to FN
Press EXIT.
To cancel end search
Press END SCH again.
End search
When you use a cassette without Cassette Memory, End search does not work once you
eject the cassette after you have recorded on the tape. If you use a cassette with Cassette
Memory, End search works even once you eject the cassette.
When you use a cassette without Cassette Memory, End search does not work once you
eject the cassette after you have recorded on the tape. If you use a cassette with Cassette
Memory, End search works even once you eject the cassette.
If the tape has a blank portion between recorded portions
End search may not work correctly.
End search may not work correctly.
Checking recordings
– End search/Edit search/Rec Review
– End search/Edit search/Rec Review
EDITSEARCH
FN
38
Edit search
You can search for the next recording start point. You cannot monitor the sound.
(1) Set the POWER switch to CAMERA.
(2) Hold down EDITSEARCH. The recorded portion is played back.
(2) Hold down EDITSEARCH. The recorded portion is played back.
Release EDITSEARCH to stop playback. If you press START/STOP, recording
begins from the point you released EDITSEARCH.
7 – :To go backwards
+ :To go forwards
begins from the point you released EDITSEARCH.
7 – :To go backwards
+ :To go forwards
Rec Review
You can check the last recorded section.
(1) Set the POWER switch to CAMERA.
(2) Press the 7 – side of EDITSEARCH momentarily.
(2) Press the 7 – side of EDITSEARCH momentarily.
The section at which you have stopped recording most recently is played back
for a few seconds, and then your camcorder returns to standby.
for a few seconds, and then your camcorder returns to standby.
Checking recordings – End search/Edit search/Rec Review
39
Playback – Basics
You can monitor the recorded tape on the LCD screen. If you close the LCD panel, you
can monitor the playback picture in the viewfinder. You can also control playback using
the Remote Commander supplied with your camcorder.
can monitor the playback picture in the viewfinder. You can also control playback using
the Remote Commander supplied with your camcorder.
(1) Set the POWER switch to VCR while pressing the small green button.
(2) Press OPEN to open the LCD panel.
(3) Press
(2) Press OPEN to open the LCD panel.
(3) Press
to rewind the tape.
(4) Press
to start playback.
(5) Adjust the volume following the steps below.
1
Press FN to display PAGE1.
2
Press VOL. The screen to adjust the volume appears.
3
Press – (to turn down the volume)/+ (to turn up the volume).
4
Press
OK to return to PAGE1.
To return to FN
Press EXIT.
To stop playback
Press
in the stop state.
To rewind the tape
Press
in the stop state.
To fastforward the tape
Press
in the stop state.
To view a still image (playback pause)
Press
during playback. To resume playback, press
again. When playback
pause lasts for about five minutes, your camcorder automatically enters the stop state.
If you leave the power on for a long time
Your camcorder gets warm. This is not a malfunction.
Your camcorder gets warm. This is not a malfunction.
— Playback – Basics —
Playing back a tape
4
3
1
5
2
VOL
–
+
OK
VCR
MEMORY/
NETWORK
CAMERA
OFF(CHG)
POWE
R
The bar indicator
40
To display the screen indicators – Display function
Press DISPLAY/BATT INFO on your camcorder or DISPLAY on the Remote
Commander supplied with your camcorder.
The indicators disappear from the screen.
To make the indicators appear, press DISPLAY/BATT INFO or DISPLAY on the
Remote Commander again.
Commander supplied with your camcorder.
The indicators disappear from the screen.
To make the indicators appear, press DISPLAY/BATT INFO or DISPLAY on the
Remote Commander again.
About date/time and various settings
Your camcorder automatically records not only images on the tape but also the
recording data (date/time or various settings when recorded) (Data code).
Follow the steps below to display the data code using the touch panel or the Remote
Commander.
recording data (date/time or various settings when recorded) (Data code).
Follow the steps below to display the data code using the touch panel or the Remote
Commander.
Using the touch panel
(1) Set the POWER switch to VCR, then play back the tape.
(2) During playback, press FN and select PAGE2.
(3) Press DATA CODE.
(4) Select CAM DATA or DATE DATA, then press
(2) During playback, press FN and select PAGE2.
(3) Press DATA CODE.
(4) Select CAM DATA or DATE DATA, then press
OK.
(5) Press EXIT.
[a] Time code/Tape counter
[b] SteadyShot off
[c] Exposure
[d] White balance
[e] Gain
[f] Shutter speed
[g] Aperture value
[b] SteadyShot off
[c] Exposure
[d] White balance
[e] Gain
[f] Shutter speed
[g] Aperture value
Playing back a tape
Date/time
Various settings
DISPLAY/
BATT INFO
BATT INFO
DATA CODE
DISPLAY
JUL 4 2003
12:05:56 PM
12:05:56 PM
50min
0:00:23:01
AUTO
50min
0:00:23:01
6 0 AWB
F1.8 9 dB
[a]
[b]
[c]
[d]
[e]
[b]
[c]
[d]
[e]
[ f ]
[g]
[g]
Click on the first or last page to see other DCR-TRV60 / DCR-TRV60E / DCR-TRV70 (serv.man3) service manuals if exist.